Question about 2004 Saturn ION

Open Question

Remove and replace broken antenna on a 2004 saturn ion must replace the base as well

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrScary66613
  • 1990 Answers

SOURCE: broken antenna

It is not Very Easy to get to But, You can access this through the Fender Holes under the Hood. Please Rate My Response! Thanks!

Posted on Feb 05, 2009

  • 1 Answer

SOURCE: Tacoma radio antenna

Use an antenna wrench to remove the chrome nut (I found a wrench on JC Whitney's website). Once the nut's removed, do the following (copied from the factory service manual):

REMOVE ANTENNA ROD

(a) Turn the ignition switch to ”LOCK” position.
(b) Press the ”AM, FM” buttons on the radio receiver, and simultaneously
turn the ignition switch to ”ACC” position.
HINT:
�� The rod will extend fully and be released form the motor
antenna.
�� After removing the antenna rod, leave the ignition switch
on ”ACC” position.
NOTICE:
To prevent body damage when the antenna rod is released,
hold the rod while it comes out.
2. Auto Antenna Models:
INSTALL ANTENNA ROD
(a) Insert the cable of the rod until it reaches the bottom.
HINT:
�� When inserting the cable, the teeth on the cable must face
toward the rear of the vehicle.
�� Insert the antenna approx. 300 mm (11.8 in.).
(b) Wind the cable to retract the rod by turning the ignition
switch to ”LOCK” position.
HINT:
�� If the ignition switch is already in ”LOCK” position, do step
1 (c) first, then turn the ignition switch to ”ACC” position.
�� In case the cable is not wound, twist it, as shown in the
illustration.
�� Even if the rod has not retracted fully, install the antenna
nut and inspect the antenna rod operation. It will finally retract
fully.
(c) Inspect the antenna rod operation by pressing the radio
wave band select buttons.

You can buy a new power mast online (ex. Discount Toyota Parts) for about $30.

Posted on Apr 04, 2009

  • 25 Answers

SOURCE: 2004 Saturn Ion transmission

It should be on the drivers side and it looks like the oil dipstick. Usually the top of the handle is shaped like a " T ". Most of the time it will be yellow and say trans on it. It may be lower than the oil dipstick. Good luck.

Posted on May 10, 2009

  • 1986 Answers

SOURCE: How do you get to the front turnsignal bulb to

Open the hood and look behind the headlamp assembly and you should see some clips / pins. Pull up on the retaining pins and the headlamp should slide forward and out of the way. You will then see the electrical connector, disconnect it. Look at where the signal assembly is and you should see the socket for the bulb, just twist counter clockwise and it will pop out for you to change

Posted on Sep 16, 2009

  • 1 Answer

SOURCE: replacing struts on a 2004 Saturn Ion

i just got a quote from meinke for front struts replaced for just over 500.00

Posted on Oct 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does a Saturn ion gasoline look like


It's leaking gas, you have a leaky fuel tank or broken seal or fuel line.

Jul 23, 2017 | Saturn Cars & Trucks

1 Answer

My key will not open the drivers side door on my 2004 Saturn Ion


Disconnected from inside door.....remove door card and inspect, could just have come off or broken!

Oct 25, 2014 | 2004 Saturn ION

1 Answer

Where would the fuse or relay for fuel pump be located in my 2003 ion


Look in the interior fuse block. It is located on the drivers side of the center counsel, just to the right or where our right leg would be. You will need to remove the trim panel. The fuses will be labeled on the inside of the panel. Page 5-96 http://www.saturn.com/content/dam/saturn/northamerica/usa/nscwebsite/en/Home/Owners/Owner_Resources/Manuals/en/us/2004/ion/2004-saturn-ion-owners-manual.pdf#page325

Apr 06, 2013 | 2003 Saturn ION

1 Answer

Where is the remote wire for a 2004 saturn ion on a stock radio


they don't have a remote wire unfortunately, you will have to wire your amp on, or remote signal to key on power supplied to the radio, and your amp will come on when you start the car as your radio does.. the only other option is if you have power antennae you can tap into that power source as it turns on when you turn the radio on..

Nov 05, 2010 | 2004 Saturn ION

1 Answer

The ignition key broke off in the cylinder of my 2004 Saturn Ion. How do I remove the cylinder if the switch is in the off position with the broken key still in it?


If the key is all the way in, it should turn the lock, with a screwdriver. It might not start without a chip if it has one, but if you hold the chip close by it should start, then I would get a pick, a dental tool, something real sharp, fine, hard, and pull the key out. Get a new one made, Hope this helps.

Aug 13, 2010 | 2004 Saturn ION

1 Answer

I need to know how to replace the side mirror on 2007 Saturn Ion


You may be lucky and just have to remove the top section just behind the mirror. Usually you have to remove the door panel to access the bolts.

Apr 28, 2010 | 2007 Saturn ION-2 Quad Coupe

2 Answers

The hood latch cable broke under the hood how can i open it


Saturn Vue hood release can be opened (if the cable is not broken) by disconnecting the cable from the back of the release lever, grabbing the ball on the end of the cable with some large pliers ("channel locks") and pulling hard. A metal "wire keeper" bracket clamped to the cable end under the hood to serve as a spacer and the release lever works.
The purpose of this bulletin is to provide a procedure for opening the hood on the Saturn VUE and ION vehicles should the hood latch release cable mechanism become inoperative.

VUE Hood Opening Procedure Modify the Saturn radio antenna by bending the antenna mast 1 in. (2.54 cm) above the antenna base to a 25 degree angle

Open hood of similar vehicle to locate hood latch release cable to hood latch attachment point.

Using modified antenna, note approximate location that antenna will have to enter in between fascia and hood to access the hood latch cable attachment point. This should be toward the left edge of the Saturn emblem. Also note position of the modified antenna base. It should be angled downward.

Note: Use protective tape on the hood and fascia where the antenna will be inserted to protect the surfaces from scratches
On vehicle with inoperative latch, insert antenna between hood and fascia and depress the hood latch cable until the hood is opened.

Good luck and thank you for using fixya

Mar 15, 2010 | 2003 Saturn VUE

2 Answers

Replacing struts on a 2004 Saturn Ion


Firs thing is you need to get a spring compressor and working with one of these tools is dangerous. If it is not secured right the spring can expand and fly right through the car or you. after you have installed the spring compresser and locked it down. you can remove all the attaching parts to remove the strut. If you have any doubts you may be better off taking it to a tech so that the job is warranteed.

Dec 03, 2008 | 2004 Saturn ION

Not finding what you are looking for?
2004 Saturn ION Logo

Related Topics:

774 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...