Question about 2005 Honda Odyssey

2 Answers

I hit passenger sliding door on garage door while

I hit front edge of the passenger sliding door on garage door frame while the sliding door was open. If I push on the sliding door while it is closing, the door will close and latch. The sliding door does attempt to latch but it does not close by itself and reopens.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 5 Answers

FLICK THE SWITCH ON UR REMOTE. LISTEN TO WHERE TH CLICKING SOUND IS COMMING FROM. I T COULD BE IN THE FRONT OR SLIDING DOOR . USUALLY , WHEN U HEAR A CLICKING SOUND, IT MEANS AN ELECTRICAL SHORT.

Posted on Dec 11, 2014

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

The door is out of adjustment. you could also have something bent. those are very heavy doors and I would recommend to take it to a honda dealer only for repairs. I helped a gentleman in your exact same situation and it took a 20 year tech all day to get it right.

Posted on Feb 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the front driver side power window switch on a 2008 Buick Enclave



Armrest Door Pull

Remove Rubber Cover

Remove 10mm *****
The first step is to pry out the plastic trim plate behind the chrome colored door release handle using a small flathead screwdriver.Then remove the 10mm ***** behind the plate using a ratcheting wrench with an extension bar attached.
Next pry out the rubber cover at the bottom of the door pull located in the center of the arm rest. Use a Torx T-25 (star bit) screwdriver to remove the two screws.
Remove Torx T25 Screws

2 T-25 Torx & 1 10mm *****

Pry Up Arm Rest Panel
Use a flathead screwdriver to pry up the rear of the plastic arm rest panel. There is a plastic hook at the front of the panel, so only pry it up from the rear edge.
Lift Rear End First

Plastic Hook At Front of Panel

Power Window Connector
After you lift out the arm rest panel, you'll need to disconnect the power connector for the window and door lock switches.
Push Connector Release Tab

Power Connector Unplugged

Two More T25 Screws
Push on the release tab with a flathead screwdriver and pull out the power window / door lock connector.Use a Torx T25 screwdriver to remove the two screws located below the arm rest panel.
Remove T25 Torx Screws

Outer Edge of Panel

Push In Center of Fastener
Then move to the outer edge of the door panel and locate the two small round fasteners. Use a small screwdriver to pop in the center pins of the two fasteners.
Pull Out Plastic Rivet

Black Plastic Fastener Removed

Remove Lower Fastener
Pull out the two plastic rivet fasteners and set them aside in a safe place.
Pull Panel Away From Door

White Plastic Pop Rivets

Pull Off Sail Panel
Grab the door pull in the arm rest and tug it towards yourself to disengage the pop rivet friction fasteners that hold the panel to the door frame.Move to the top corner of the door panel and pry off the triangular "sail" panel. On some vehicles, the sail panel contains the tweeter speaker.
Lift Panel Off Door Lock

Pull Out Door Pull Cable
Lift the door panel off the door lock button and tilt the top of it out towards yourself.Use a pair of needle nose pliers to gently lift the metal ball at the end of the door opener cable out of the mechanism.
Disconnect the door cable from the back side of the door panel.
Door Pull Cable Removed

Disconnect Power Mirror
Then disconnect the power connector for the side view mirror by lifting up on the release tab. Slide the power connector off the plastic anchor on the metal door frame.
Slide Connector Off Anchor

Unlock Connector

Connector Detached
Look behind the door panel and locate the large wire connector with the pink lever lock. Swing the lever open to unlock the connector and separate it from the socket.


Door Panel Removed

Power Window Motor

10mm Bolts
Now the door panel can be completely removed by lifting it up and off the door frame.To replace the power window motor, remove the 10mm bolts.
Stock OEM Door Speaker

Remove 7mm *****
The stock "OEM" speaker is held in place by a single 7 mm *****. Remove it with a socket and ratcheting wrench.
Pry Off OEM Speaker

Speaker Removed

Disconnect Power Plug
If the speaker is stuck to the door frame, gently pry it off with a small flathead screwdriver.Disconnect the speaker's power plug by pressing the release tab with the small flathead screwdriver.
Fits 5.25", 6.5", 6.75"

Re-installing Door Panel
According to the Crutchfield website, the 2008 to 2012 Chevrolet Malibu's front door speakers can be replaced withaftermarket speakers in the following sizes: 5 1/4", 6 1/2" or 6 3/4" speakers with the use of a bracket.If you'd like to reduce road noise, make your car quieter and also improve the sound from your speakers, I'd recommend applying some Dynamat Sound Deadener on to the metal door frame.
Re-Attach To Anchor

Plug In Power Side View Mirror

Re-Insert Power Connector
To re-install the door panel, first hold the panel close to the door frame before re-connecting the large wire plug. Swing the pink lever closed to lock it in place.Slide the socket for the power side view mirror back on to its anchor and insert the power plug.
Lock Power Connector

Pink Lever Locked

Re-Insert Door Pull Cable Ball
Insert the metal ball at the end of the door opener cable back in to the door handle mechanism.Slide the black plastic cone part of the cable back into the slot in the door opener assembly.
Door Opener Cable Reinstalled

Hang Door Panel On Frame
Gently lower the door panel down on to the edge of the door frame with the door lock switch through the opening at the top.
Line Up White Plastic Fasteners

Push On Sail Panel

Push Door Panel In Place
Move to the bottom of the door panel and line up the white plastic pop rivet fasteners with the holes in the metal door frame.Push all around the door panel to re-insert the pop rivet fasteners.
Re-attach the sail panel at the top corner of the door frame.
Push Panel Flush Against Frame

Insert Side Edge Fasteners

Insert Larger Piece First
Next move to the side edge of the door panel and first re-insert the larger piece of the two fasteners. Then insert the smaller "pin" piece of the fastener into the middle of the larger piece.
Insert Small "Pin" Piece

Install Lower Edge Fastener

Tighten 2 T25 Torx Screws

Re-Attach Power Connector

Insert Front Hook First
Insert and tighten the two Torx T-25 screws located under the arm rest.Re-attach the power connector to the plastic arm rest panel.
First insert the hook at the front of the arm rest panel and then snap the rear end in place.
Pop Arm Rest Panel In Place

Tighten 2 T25 Screws

Replace Rubber Cover
Insert and tighten the two T25 Torx screws into the door pull cup. Then replace the rubber cover over the two screws.
Tighten 10mm Door Handle *****

Replace Door Handle Trim Plate

Malibu Door Panel Replaced
Replace the 10mm ***** that goes above and behind the door opener handle and tighten it. Pop in the plastic trim plate behind the door handle.

Apr 10, 2016 | Buick Cars & Trucks

2 Answers

My honda odyssey ex 2008 the doors do not move on


Do a reset on the door system, by pulling the door fuse. I don't have location, possibly drivers side fuse box.

Sep 15, 2014 | 2008 Honda Odyssey

1 Answer

Doorhandle


for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Mar 24, 2014 | 2003 Toyota Avalon

1 Answer

1990 celica passenger side door lock wont open manually or electronicly, cant take the panel off because of the three screws two in back one in front of the door frame any suggestions


A body repair shop or your local police dept.should have a ''SLIM JIM'',a tool that slides between window & weatherstripping of door to move lock rod inside.

Jan 24, 2013 | 1990 Toyota Celica

1 Answer

My rear passenger door will not open from the inside of the car. When the handle is pulled the door will not open. It will open from the outside.


It has kid locks on edge of door. Open door and look along edge of door for a small sliding lever. Good luck.

Nov 29, 2012 | 2002 Toyota RAV4

1 Answer

My Toyota Avalon passenger door makes a clicking noise when opening or closing. What could cause this?


if the click happens when the door is almost completely open then there is an over center cam that latches the door open so it doesnt just swing back at you .. the cam is visible near or on the door hinges ... if there is any loosness in the pivot pin then it will snap each time you go over the latch point .. heavy greese on its pivot pin might quiet it down .. if the click happens just as the door is opened then make sure the door front edge is not hitting the fender edge. of course lube the hinges and make sure they are not loose ...

Jul 04, 2010 | 2005 Toyota Avalon

1 Answer

The Front Passenger Door won't open from the inside only at the o


You might find a plastic toggle lever in the edge of the door. Your car may have a childproof lock for the front passenger door like the rear doors do. If so, it is a simple matter of moving the toggle.

Jun 30, 2009 | 1998 Volvo V70

2 Answers

TROUBLESHOOTING PASSENGER SLINDING DOOR


what is the problem with door?. if it will not operate from electrical control,try removing and reinstalling fuses #11 tru #15.

Jun 10, 2009 | 2000 Honda Odyssey

1 Answer

1997 honda civic back doors wont open, hit frame lock in frame


Please Please - I am in the same boat. Does anyone know what to do?

May 25, 2009 | 1997 Honda Civic

2 Answers

Honda Odyssey doors


I read about this issue while I was looking for a fix to mine. Try the following:

Remove fuse #13 for 30 seconds or more from the passenger side fusebox. This will reset the door and the clock.

OR

1.) Disable the power door switch on the left dashboard.
2.) Remove the power door fuses located under the front passenger leg area.
3.) Manually open and close both sliding doors.
4.) Restore the power door fuses located under the front passenger leg area.
5.) Enable the power door switch on the left dashboard.
6.) Try opening the sliding doors.


http://www.topix.com/forum/autos/honda-odyssey/TD1QRDMAQ28J8EDA0

Sep 03, 2008 | 2002 Honda Odyssey

Not finding what you are looking for?
2005 Honda Odyssey Logo

389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...