Question about 2002 Audi A4

Open Question

Instructions for removing boot lock on audi a4 convertible

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Removing rear bumper on Audi A4 1997 to fit tow bar

Did you get the solution to this, I have the same problem

Posted on Jul 14, 2008

Ad
TLRogue
  • 99 Answers

SOURCE: Audi A4 (A3) Boot won't open

if unable to turn key in boot then you will have to drop the seats down inside and climb in. remove the rear door panel and move the release mechanism manually. Make sure the vac pipes are connected and the mechanism isnt siezed.

TL

Posted on Jan 21, 2009

chain saw
  • 94 Answers

SOURCE: electrical fault Audi A4 2002

PRISE OUT THE TRIM PANEL AT THE BASE OF THE ARMREST WITH A FLAT-BLADED TOOL UNDO 2 SCREWS(DRIVERS DOOR) SINGLE SCREW ACCESSIBLE THOUGH THE ARMREST ON PASSENGER SIDE ,NOW GO TO THE BASE OF THE DOOR TRIM UNDO THE SCREW IN THE CENTRE,ONTO THE TOP TRIM NOW ABOVE THE RELEASE HANDLE,STARTING AT THE FRONT EDGE(DOOR HINGE SIDE) CAREFULLY PULL THE TRIM PANEL AWAY FROM THE DOOR TO RELEASE THE CLIPS,THEN SLIDE IT TO THE FRONT TO UNHOOK THE REAR EDGE OF THE TRIM PANEL,UNDO THE 4 SCREWS YOU CAN SEE,UNHOOK CABLE FROM REAR OF INTERIOR DOOR HANDLE,DISCONNECT WIRING PLUGS SPEAKER ,WINDOW MOTOR CONTROL UNIT AND THERE YOU HAVE IT ..EASY... IF YOU START NOW YOU WILL HAVE IT FINISHED IN 2 DAYS...ONLY JOKING....SHOULD TAKE 1 HOUR..HOPE THIS WILL BE OF SOME HELP TO YOU...LET ME KNOW HOW YOU GOT ON

Posted on Feb 10, 2009

  • 21 Answers

SOURCE: Audi A4

Not sure if they've changed it but this is what i do for my 99 a4

First remove the screw in the handle pull, it should be next to where your fingers go.
Pull down on the black piece of plastic and remove the screw form the door
Then remove the screws on either end of the door, one near the door jam on top and one near the other side, same place.
Finally pull up then out and the door panel should come out

Hope that helps

Posted on Jun 17, 2009

  • 47 Answers

SOURCE: audi a4 2.8 1995 model

  1. Remove the hubcap or center cap.
  2. Loosen but do not remove the hex collar bolt.
  3. Loosen but do not remove the wheel lug bolts.
  4. Raise and safely support the vehicle.
  5. Loosen all, and remove all but one of the CV joint to stub axle bolts retaining the halfshaft to the transaxle flange. If necessary have an assistant hold the tire, or remove the tire, install two of the lug bolts and have an assistant hold a suitable and sturdy 3 foot (1 meter) prytool between the lug bolts to prevent the axle from spinning.
  6. If not previously removed, remove the front wheels.
  7. Remove the remaining CV joint to stub axle bolt and remove the halfshaft from the transaxle drive flange and support it out of the way. Do NOT let it hang unsupported.
  8. Remove the outer axle hex collar bolt and press the halfshaft out of the hub. A suitable press tool may be necessary, otherwise drive the axle out using a suitable drift.
  9. Remove the ABS wheel speed sensor cable from the brake caliper bracket.
  10. Slide the ABS speed sensor partly out of its mount.
  11. Remove upper control arm pinch bolt and nut, then remove both arms up and out of the steering knuckle.


WARNING The slots in the steering knuckle must not be widened. Do NOT loosen any other steering knuckle fasteners, otherwise the axle geometry must be checked.
  1. Tilt the steering knuckle out and to the rear of the vehicle, then remove the halfshaft. If necessary, use a press tool to remove the axle from the hub.



0900c152800c2fa3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. A threaded plastic guide dowel is included in the vehicle's tool kit. Thread it into place to guide the wheel on the ground
Fig. Apply a light coating of an anti-seizing compound to the lug bolts


Fig. The screwdriver handle supplied in the vehicle's tool kit is used to start the lug bolts
Fig. Always loosen or tighten the axle nut or bolt with the vehicle on the ground
  1. Install the halfshaft into the wheel hub.
  2. Install the upper control arms into the steering knuckle and tighten to:
  3. Upper steering knuckle pinch bolt: 30 ft. lbs. (40 Nm).
  4. Install the wheel and hold it to keep the axle from turning. If necessary have an assistant hold the tire, or with the wheel removed, install two of the lug bolts and have an assistant hold a suitable and sturdy 3 foot (1 meter) prytool between the lug bolts to prevent the axle from spinning.
  5. Attach the inner halfshaft-to-transaxle flange and tighten to:

Inner CV joint-to-transaxle flange:


M8 fasteners: 30 ft. lbs. (40 Nm) M10 fasteners: 59 ft. lbs. (80 Nm)
  1. install the ABS wheel speed sensor, and the sensor cable into the caliper bracket.
  2. If not previously installed, install the wheel without the wheel trim and do not fully tighten the lug bolts.
  3. With the wheels installed and the vehicle on the ground, tighten the lug bolts in a crisscross pattern and then the axle bolt as follows:
  4. Wheel lug bolts: 89 ft. lbs. (120 Nm)

Posted on Jul 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't open boot on 96 Audi A4


if unable to turn key in boot then you will have to drop the seats down inside and climb in. remove the rear door panel and move the release mechanism manually. Make sure the vac pipes are connected and the mechanism isnt siezed.

Jul 31, 2012 | 1996 Audi A4

1 Answer

My car is a 1997 audi a4 and doesnt have remote locking but does have central locking. used to work fine but now the key only unlocks the drivers door. the other doors will not unlock. however if i unlock...


I would start with driver door lock , not the lock cyllinder , but lock assembly which is inside the door and have switches build in to it.

Jun 22, 2010 | 1997 Audi A4

1 Answer

Convertible top has to be put down/up manually.


Just took my 2004 A4 convertible (25,000 miles) to the dealer...needed new module...cost $375 for part and $300 for labor. Maybe this should be a recall item.

Apr 05, 2010 | 2007 Audi A4 Convertible

1 Answer

1999 Audi A4 A4 audi central locking not working how can i open the boot with out it the key i have doesnt unlock the boot


Open the drivers door with the key. Look on the door for the unlock button and press it. This will unlock all doors and the boot. Use the handle on the boot to open it.

Jan 23, 2010 | 1996 Audi A4

1 Answer

I need to get to the trunk lock mechanism but can't seem to figure out how to remove the lining from the trunk lid. Audi A4. I have the convertable top down and the service light says close the trunk. I...


The liner is held on by little plastic studs. It can be gently pried off Then you will have access to the lock. The lock should have a nut on it that holds it to the trunk. Turn nut counter-clockwise to remove.

Nov 15, 2009 | 2004 Audi A4

1 Answer

2006 Audi A4 keyless entry programing instructions


This happened to me, all you have to do is open the drivers door, insert the key into the ignition, turn the ignition on, off, on, off, on, off, now remove the key and press the lock button on the remote and the car should lock. Be sure to check the other remote, it may have been knock off. If so repeat the steps above for each remote.

I hope this helps.

Sep 03, 2009 | 2006 Audi A4

1 Answer

Audi A4 02 door wont lock.


CHECK UNDER THE RUBBER BOOT,WERE THE DOOR HINGES ARE, AND CHECK FOR BROKEN OR CUT WIRING. IT IS A PROBLEM WITH THE AUDI A4

Apr 09, 2009 | 2002 Audi A4

1 Answer

Audi A4 (A3) Boot won't open


if unable to turn key in boot then you will have to drop the seats down inside and climb in. remove the rear door panel and move the release mechanism manually. Make sure the vac pipes are connected and the mechanism isnt siezed.

TL

Jan 12, 2009 | 1998 Audi A4

3 Answers

A4 cabriolet boot will not close?


have you tried disconnecting the wires this will tell you if its the motor or the lock itself. joe

Dec 04, 2008 | 2007 Audi A4 Convertible

1 Answer

Boot opening


It shouldnt be a problem.but since most cars are equiped with remote keys, the manual keys are rarely used on the boot. and it tends to dry and get stuck, try spraying wd40 or lock oil in it and try after a while, goodluck.

Aug 02, 2008 | 2001 Audi A4

Not finding what you are looking for?
2002 Audi A4 Logo

Related Topics:

724 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...