Question about 1999 Plymouth Grand Voyager

Open Question

How to replace a blower motor in a 1999 plymouth voyager

Posted by on

  • tim mcgrath May 11, 2010

    which motor have also need 8th digit of vin

×

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wracefans24
  • 1985 Answers

SOURCE: replace blower motor 1998 plymouth voyager

it is located behind and below the glove box,you might want to remove the glove box assembly to see it easier,
there are four screws holding a blower motor cover you to take off first,now remove the screws holding the blower motor up,disconnect the motor wires.
if your changing this because you think its bad,you should test the blower motor wires with a test light with the key on and blower switch turned on.if you have power in the wires,then it is bad.
but if you have no power in wires it could be blower motor resister,or switch.

Posted on Dec 06, 2009

  • 67 Answers

SOURCE: 1999 plymouth voyager blower motor

you have to replace it its located on the passenger side under the dash

Posted on Feb 04, 2010

motor1258
  • 6674 Answers

SOURCE: how do you remove and replace a blower motor on a

Caution : BEFORE STARTING, DISCONNECT BATTERY ( - ) NEGATIVE CABLE FROM BATTERY TO AVOID POSSIBLE AIR BAG DEPLOYING, AND WAIT 3 or 4 minutes before beginning to be sure.. Removing glove box will make it easier. In behind there, you'll see a cover over motor, remove it, then you'll see motor and fan wheel. Remove wiring connector and push it back through into housing . Remove 3 screws holding motor/fan assembly and lower it down and out of housing. Reverse procedure for install, and don't forget wiring back through housing and grommet on wiring. Re-connect battery clamp after all installed and test it. Good Luck.

Posted on Nov 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove and replace a blower motor on a 1999 Plymouth Grand Voyager?


Caution : BEFORE STARTING, DISCONNECT BATTERY ( - ) NEGATIVE CABLE FROM BATTERY TO AVOID POSSIBLE AIR BAG DEPLOYING, AND WAIT 3 or 4 minutes before beginning to be sure.. Removing glove box will make it easier. In behind there, you'll see a cover over motor, remove it, then you'll see motor and fan wheel. Remove wiring connector and push it back through into housing . Remove 3 screws holding motor/fan assembly and lower it down and out of housing. Reverse procedure for install, and don't forget wiring back through housing and grommet on wiring. Re-connect battery clamp after all installed and test it. Good Luck.

Nov 09, 2010 | 1999 Plymouth Grand Voyager

1 Answer

My 2001 Voyager blower fan only runs on high.


This is 100% the Blower (Fan) Motor Resistor located near the Blower Motor.
This is a very common problem with Chyrsler, Dodge, Plymouth. The key symptom is the Fan only working on High.
This is very easy to access and replace.

Let me know if this helped....

May 11, 2010 | 1999 Chrysler Sebring

1 Answer

1999 plymouth voyager blower motor


you have to replace it its located on the passenger side under the dash

Feb 04, 2010 | 1999 Plymouth Voyager

1 Answer

Replace blower motor 1998 plymouth voyager


it is located behind and below the glove box,you might want to remove the glove box assembly to see it easier,
there are four screws holding a blower motor cover you to take off first,now remove the screws holding the blower motor up,disconnect the motor wires.
if your changing this because you think its bad,you should test the blower motor wires with a test light with the key on and blower switch turned on.if you have power in the wires,then it is bad.
but if you have no power in wires it could be blower motor resister,or switch.

Nov 28, 2009 | 1998 Plymouth Voyager

2 Answers

1996 plymouth voyager van blower --high only


YOUR BLOWER MOTOR RESISTOR IS BAD OR THE BLOWER MOTOR CONTROL SWITCH COULD BE FAULTY.

Sep 13, 2009 | 1996 Plymouth Voyager

1 Answer

Replacing Blower fan info


Should be only 3 screws holding it in Unplug, remove the screws and remove the blower motor.

May 29, 2009 | 1999 Plymouth Grand Voyager

1 Answer

I have a 1999 Plymouth Voyager, the Blower Motor is out, I just got a new one to replace it, but I want to make sure the correct positioning of where the blower motor is placed at?


It should have 3 screws. If it has a hose, line it up with the case outlet spout to put the hose on. If no hose, just put it where the wire connection is close to where the wiring is hanging.

Mar 30, 2009 | 1999 Plymouth Voyager

1 Answer

Blower motor


It's in behind glove box, you will probably have to remove glove box, but a good look up from under will tell you. You did check fuses & resistor right? Did it run for a while on high only?

Jan 08, 2009 | 1999 Plymouth Grand Voyager

Not finding what you are looking for?
1999 Plymouth Grand Voyager Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...