Question about 2000 Chevrolet Blazer

1 Answer


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 580 Answers

It sounds like the bendix drive on your starter is sticking or your starter ring gear is striped. Remove the starter & check action of the bendix drive & check the ring gear for excessive wear, Good hunting!

Posted on Feb 06, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How can I test starter put in junk starter changed cables and body ground and the starter was smoking no spin

Remove the spark plugs if petrol or glow plugs if diesel, then try to spin motor.

Mar 24, 2015 | Cars & Trucks

2 Answers

Starter clicks but will not turn engine over on 2004 Dodge Durango. New starter and battery.

Hi Mark
Sounds like you are doing all the right things.
We used to Load Test a Starter Motor by putting it in a Large Vice and connecting a known good battery with solid fat jumper leads.
When the solenoid throws the cog forward to engage we would use a 2 by 4 block of wood levered against the cog to try and stop the starter from spinning. The wood burns up under load but it quickly proves the Starter is functioning under load. Without using the engine.
Also you could try removing the spark plugs on the engine to allow the compression to escape. Make sure NO sparks around to ignite any fuel vapor.
The engine should spin over easily like this and you can hear & see if anything is binding up.
Hope this Helps!
Good luck!

Mar 03, 2015 | 2004 Dodge Durango

1 Answer

Wont start when hot

The starter is effected by heat. Does the motor spin just as fast when trying to start it when the motor is hot? If it cranks real slow it is the starter. If it cranks over at the same speed it is not the starter.

Get an account on a mini cooper forum and post the question there. you could also try a small spray of starting fluid into the air cleaner. If it starts and stalls then it is a fuel delivery issue. If it does not start then remove a spark plug and verify that there is a spark as the motor cranks over. Check for any blown fuses.

Dec 13, 2013 | Mini Cars & Trucks

2 Answers

How do i get my 1996 chevy tahoe distributer back in time

Remove #1 spark plug ( front left ) stuff shop rage in spark plug whole. use screw driver to helt stop up hole just bump starter a few times till you hear a POP that will be top dead center #1 check timing pointer and marks front pully adjust top cemter place dist. in appropriate pos with roter in corect position

Mar 22, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

Replaced starter car still won't start

if the engine does not run, 90 percent of the time it is starved for fuel, or has no spark. the only time the starter is suspect is if the engine's crankshaft does not spin when the starter is engaged. so you replaced the starter, but the problem most likely lies in the fuel supply or spark.

Nov 22, 2010 | 1996 Isuzu Rodeo

1 Answer

Got spark will not run

Spray starter fluid in the intake. If the engine starts on the fluid (it'll die once it burns off the fluid) then you likely have a bad fuel pump. You'll want to check the fuse for the pump and the relay (the relay should click when you first turn the key on, it helps to have someone do this while you listen to the relay) before you replace the pump. If you have a volt/ohm meter, check for voltage at the fuel pump as well. If you have voltage there and the pump doesn't run, replace the pump.

Nov 13, 2010 | 1993 Mazda 626

1 Answer

96 chevy cheyenne V6 4.3 liter how do i put back the distributor back in

remove the number one spark plug, get some one to hold there finger over plug hole till it blows your finger off the plug hole, bumping the starter slowly till it blows off, stop there to see if number one piston is all the way up top dead center, drop in distrubutor with rotor pointing at number one on the cap , after its in ,seated, look to insure the rotor is pinting to number one on distributor cap, that should crank there till you can get a timing lihgght on it, hope this helps you ,thanks robert b.

Jun 07, 2009 | 1989 Chevrolet C1500

3 Answers

95 Buick Skylark Stops Running

the fuel pump is slowly going out

Dec 01, 2008 | 1995 Buick Skylark

1 Answer

Car won't start

If by "trying to start" you mean that the engine is turning then it isn't the starter that's bad as a couple have said. The starter's sole purpose is to spin the engine so it can start if, gas, spark, compression and timing are correct. If any one of those four are not available the starter can spin the engine until the battery dies and it won't start. If you don't know how to check for proper delivery of fuel, spark, timing and compression then I'd suggest taking it to a reliable mechanic.

Jun 11, 2008 | 2003 Renault 181

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides