Question about 2005 Hyundai Elantra

1 Answer

I need to replace my clutch in my 2005 Hyundai Elantra 5speed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,230 Answers

Hi there,

Well the manual transmission in your Hyundai Elantra uses a clutch to engage and disengage the power from the engine to the transmission. The clutch disc is sandwiched between the engine flywheel and the transmission pressure plate. When you switch gears and let off the clutch pedal, there is a short period during which the clutch is slipping to transmit the power in a controlled way. This causes wear on the clutch...... over time it will require replacement. You can please follow the below steps -
1. Jack up the Hyundai Elantra and place on jack stands.
2. Drain the transmission gear oil into a catch pan. To drain the gear oil, loosen the drain bolt with a ratchet. Before the drain bolt unscrews completely, use your hand to unscrew it so that it doesn't fall into the drain pan.
3. Disconnect both drive axles (half shafts) from the transmission. Use a ratchet to remove the two bolts that hold the steering knuckle to the strut. Once those are out, you can easily pull the axles out of the transmission. The steering knuckle is the component that the wheel and strut attach to. You can locate the two bolts to remove by following the strut down from where it's bolted into the engine bay. Removing these two bolts allows you to pull the steering knuckle outward so you can pull the drive axle out of the transmission.
4. Remove the exhaust downpipe from the rest of the exhaust. It will be held on with two bolts at both ends and can be removed with a ratchet. Removing this piece is necessary to gain access to the transmission.
5. Disconnect any wiring connected to the transmission and remember where all the wires go.
6. Disconnect the shifter cables connected to the transmission. Use a ratchet to remove each shifter cable and its housing.
7. Remove the bolts holding the transmission to the engine block (there will be about seven or eight bolts). Place a transmission lift underneath the transmission to hold it and lower it down. If you don't have a transmission lift, you can use a transmission attachment for your jack.
8. Shift the transmission back and forth until it drops onto the jack. Pull the transmission straight back, ensuring that no pressure is put on the input shaft, then lower the transmission to the ground.
9. Remove the pressure plate and clutch disc from the flywheel with a ratchet tool. Then remove the flywheel with a ratchet tool and replace it with a new flywheel. Alternatively, have your flywheel professionally machined at a machine shop then replace it in your car. Torque the flywheel down to the manufacturer's specifications.
10. Place the clutch disc on the clutch disc alignment tool and insert the tool into the flywheel input shaft hole. Connect the new pressure plate to the flywheel and torque the bolts. Once the pressure plate is torqued down, remove the clutch alignment tool.
11. Grease the new throw-out bearing and place it on the input shaft of the transmission. Once the transmission is installed, it will push against the pressure plate.
12. Jack the transmission back into place, push the input shaft straight into the flywheel hole, push the transmission into place then bolt it down to manufacturer's specifications.
13. Reinstall the drive axles by pushing them into the transmission, then reconnect the steering knuckle to the strut, tightening the two bolts that were removed previously.
14. Reconnect the shifter cables to the transmission with a ratchet.
15. Reconnect the exhaust downpipe and wiring.
16. Add transmission gear oil to the transmission through the transmission fill plug until the fill plug begins to drip. Wait until the oil stops leaking out then tighten the plug.
17. Lower the Hyundai Elantra to the ground.

Good Luck!!

Thanks

Posted on Feb 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced transmission, and clutch. Vehicle will not start.


Check the crank sensor maybe it was damaged or fogot to connect it

Mar 10, 2015 | Hyundai Cars & Trucks

1 Answer

How do I fix 2005 hyudai elantra gt 5 speed.


they have to be in nneutral or the clutch has to be pushed in to keep you from running into or over people

Mar 09, 2015 | 2005 Hyundai Elantra GT

1 Answer

2005 hyundai elantra clutch pedal stuck up


Could be a lot things, but throw out bearing would be my first guess, or the slave or master cylinder. Other issue would be a broken clutch fork

May 19, 2014 | 2001 Hyundai Elantra

1 Answer

Hi reving when idling


Sounds like you have a vacuum leak or a bad IAC motor.

Apr 10, 2010 | 2001 Hyundai Elantra

1 Answer

I have a lose clutch on a 2003 hyundai elantra would could this be. do i need to replace my whole clutch


no you don't need to replace hole clutch , there is oil leakage form any cylinder, arrest leakage or replace that it will solve your problem.thanks

Feb 25, 2010 | 2004 Hyundai Elantra

1 Answer

Having release prblems with clutch on 2005 Elantra. new oe clutch, cut the flywheel and changed the slave cylinder. The pedal is too high not enough throw


Hello; The clutch is activated by a cable leading from the clutch pedle to the clutch housing between the engine and the trany. It is that cable that needs adjusting. If the pedle is too high to activate the clutch the cable needs to be adjusted to be shorter. That adjustment is at the clutch housing end not inside the car.

Hope that helps.

Jan 15, 2010 | 2005 Hyundai Elantra

1 Answer

Problems rplacing car stero


Check all your fuse in dash & under hood for a blown one.

Mar 22, 2009 | 2005 Hyundai Elantra

Not finding what you are looking for?
2005 Hyundai Elantra Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...