Question about 1997 Volkswagen Golf

1 Answer

Dont know where wires go on ignition barrl - 1997 Volkswagen Golf

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Volkswagen Master
  • 19,396 Answers
  • Ginko
    Ginko Feb 05, 2010


    I am sorry seeing that you left negative feedback. I thought I posted the ignition wiring diagrams as asked. I have had no further replay from you.

    Your solution had already been refunded and the rating given to the expert is only bad for the person supporting you.

    I will be grateful if you can change the negative rating given. This wont affect your right to refund.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I wire a two wire plug that plugs into an ignition control modular

You really should get an electrician if you dont know this stuff.. There is too much confusion and danger. I know the answer - but I wont tell you .. sorry

Aug 13, 2014 | Cars & Trucks

1 Answer

Installing Spark plug wires

Unless the wires were removed the firing order cannot change as also the length of the wires do not permit that the wires switch over.
All what is needed is to check the spark at each plug , if of low internsity check the ignition system including the HT coil. Also the fuel filter and the fuel pump for the right pressure.

Nov 22, 2011 | 1996 Honda Accord

1 Answer

Having problems with 99 regal passkey lock. its getting worse fast. it had a new ignition key tumbler 2 years ago but i dont know if they changed the passkey wire can i bypass it?

yes you can,fist locate the wire that goes to the key resistance,you are going to bypass it whit the resistence of a ignition wire,cut the wire in difrent lengts less than a foot,this makes difrent resistence values,put them to the wire on the car to find the one that will ignite the car.

Oct 20, 2010 | 1999 Buick Regal

1 Answer

Have power to starter continously, have replaced starter, and ignition

sounds like ur ignition barrell wiring switch (inside the car where u put the key in, theres a wiring block on the other side behind the cowelling). dont know much about mustangs to be fair, if theres a relay relating to the starter/ignition it may be worth checking out. hope this helps

Jul 13, 2010 | 2001 Ford Mustang

2 Answers

Starter wont crank on a 2000 oldsmobile intrigue

Check your manual if you have it. I believe you need to have the key in the ignition in the ON position for about 10 minutes to reset the security system.

Jul 08, 2010 | 2000 Oldsmobile Intrigue

1 Answer

I dont know where to plug in the wires from the

Get a HAYNES MANUAL for your car /auto zone ,napa

May 02, 2010 | 1994 Acura Integra

1 Answer

Wiring ca18det to ignition

im a little confused u took a ca18det out of a 240sx and put it in a old skyline??? try going on nico forum for more info

Sep 07, 2009 | 1990 Nissan 240SX

1 Answer

Bypasing ignition

Hotwiring is used inilligal activities but in your case i dont have a problem in showing you how its done.

1.) Remove the part of the dash covering your ignition key assembly
2.) There should be 5 to 8 wires there
3.) Locate 2 wires of similar color
4.) strip these wires and tie then together this will turn on the ignition
5.) find the starter wire usually blue and touch it to these wires, Imidately remove it when the car has started.
6.) tape them up

If your wireing is a bit different or you dont have similar color wires then
use steps 1 and 2 from above
3.) locate the the on positive wire
4.) run a wire grom the negative battery pole to the on positive wire. (U can strip each wire there and ground it to the wire from the battery pole , the correct one will turn the ignition on.
5.) once located tie it to the ground.
6.) touch each one of the expose wires one by one until the car tumbles and starts.

If you are still having trouble use this link

Jul 17, 2008 | 1987 Chevrolet G10

Not finding what you are looking for?
1997 Volkswagen Golf Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

75817 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides