Question about 2004 Lexus LS 430

Open Question

How do you remove the popout cup holder in center console 2004 ls430

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

I AM TRYING TO TAKEOUT A CENTER CONSOLE OUT OF A 2000 CHRYSLER INTREPID


Hi Ken, I'm glad to help! Ken I have removed so many of the center consoles on Intrepids, heck I can do it in my sleep. I'm not sure how far you have gotten removing it. But there are some hidden screws under the rear cup holder. Pull the rear seat cup holder out and there is one in the very front and 2 down inside the slot. Those are the only ones you need to remove the other screws simply hold the cup holder in. The rest of the removal is very easy. Hope this helps and have an awesome day Ken!

Apr 18, 2014 | 2000 Chrysler Concorde

1 Answer

Replacing cup holder


I assume you mean the one that flips up in the center console?

If so, there are three likely issues.

1) did you slide out the retainer from the upper screw? the top screw had a cover that had to be pried off. you then took the screw out. Lastly you have to slide out the plastic retainer that the screw went into. It slides out towards the opening.

2) you have to have the cup holder partially open to remove it. the hinged part that folds up is stored in the cavity under the console when closed. you have to open the cup holder and keep pushing until the front of the cup holder lip comes up. Work the cup holder up and down until it comes out.

3) the cup holder is stuck in place due to years of spilled liquid. If you've done the above, then you can either spray soapy water on the creases around the opening and let it set, or you can apply strategic brute force.
Be aware through. if this is the center console cup holder just behind the gear shifter. There are two screws and nothing else to hold it in. Just be carefull....

Mar 17, 2014 | Volvo S80 Cars & Trucks

1 Answer

I'm an idiot and put my engagement ring in my change holder in my 2006 Chrysler Pacifica. When I went to put it back on, it was no where to be found. I believe it slipped behind the small crack


Print I hope this helps you,good luck.Randy


Removal & Installation

Instrument Panel

  1. Disconnect and isolate the battery negative cable.
  2. Remove the center console closeout panel by removing the left and right attaching screws, then the left and right panels.
  3. Remove or disconnect the following:

    Remove the shift bezel. Remove the transmission range indicator surround bezel. Remove the two screws attaching the front floor console to the lower instrument panel. Open the cup holder and remove the two attaching screws on the bottom of the cup holder. Open the bin and remove the two attaching screws on the bottom of the bin. Remove the front floor console sidewall attaching screws, three per side. Raise the front floor console and disconnect the wiring harness. Remove the front floor console from the vehicle.

    0996b43f807cb4f3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console and shift bezel


    0996b43f807cb4f4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console, showing attaching screws

  4. Remove the floor console base assembly by removing the two screws attaching the L-brackets to the instrument panel.
  5. Remove the nuts attaching the floor braces to the instrument panel.

    0996b43f807cb4f5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of floor brace, attaching nuts, center brace, and floor bracket

May 02, 2012 | 2006 Chrysler Pacifica

1 Answer

How do I remove the center front console, where coffee cup holder hood is?


Loosen the hex head set screw from the front of the Shifter knob. Pull it off, then remove the screws on the lower sides, as well as the ones hiding under the rubber cup holder. The entire assemble will now lift off.

Oct 29, 2010 | 2004 Chrysler Pacifica

1 Answer

How to replace bulb in the shifter console . Need to know how to remove cover at the base of the shifter so I can get to bulb


Bulb is located under the P/R/N/D/2/R indicator. Normally you just need to remove the black plastic that surrounds sifter and indicator and has the cup holders.But the plastic may be brittle, so remove the center console. See photos.
527cdec.jpg

53d2055.jpg

Feb 19, 2010 | 2004 Nissan Sentra

1 Answer

I need to get under the cup holder section of the console


Hello,
I hate to be the berrer of bad news but unless you can sneek a grab at it from the side you will need to remove the whole console. I would try some of those 4 jaw flexible pincher grabbers most parts stores would cary them.

Roy

Nov 16, 2009 | 2004 GMC Sierra Denali

1 Answer

Buick Regal cup holder problem


Yes absolutely you can my friend. and you are correct this will fit 1997 to 2004 actually!

Jul 10, 2009 | 1996 Buick Regal Olympic Gold

Not finding what you are looking for?
2004 Lexus LS 430 Logo

Related Topics:

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

905 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...