Question about 1994 Ford Thunderbird

1 Answer

Freeing power steering pump pulley bolt

I'm trying to replace the water pump in my 1994 thurnderbird 3.8L. The manual says to remove the power steering pump pulley. There is a 3/8" allen socket in the center of the pulley. Even though I'm using a breaker bar even with a pipe over it, I can't get that bolt loose. Any ideas?
Thanks,
Ed

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

You need a belt rope wrench to hod the pulley, however you can remove it without taking the pulley off and put it in a vice to get it off. you will need a 3/8 ths drive ratchet to get it out with and tap it with a hammer also use a torch to heat up the outer edge to get the lock tight break loose.

Posted on Feb 05, 2010

Testimonial: "Very Helpful - thank you"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the power steering pump?


Hi Brian:
Check this REMOVAL and INSTALLATION procedure... (see Figures 2, 3 and 4)
  1. Position a fluid catch pan under the power steering pump.
  2. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan.
On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
  1. Remove the drive belt from the pulley.
  2. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.
When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
2_8_2012_3_52_57_pm.gif

Fig. 2: Installing the pilot bolt

2_8_2012_3_53_39_pm.gif

Fig. 3: Removing the power steering pump pulley



2_8_2012_3_54_28_pm.gif

Fig. 4: Installing the power steering pump pulley

  1. On most models, it may be necessary to unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  2. If equipped, unfasten the power steering filler tube bolt and remove the filler tube.
  3. Remove the rear brace retainers and the brace.
  4. Remove the power steering pump-to-bracket bolts and then remove the pump from the vehicle.
To install:
  1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm) 2.2L engines. (50 Nm). On 4.3L engines tighten the bolts to 37 ft. lbs. (50 Nm).
  2. If equipped, install the rear brace and tighten the retainers to 22 ft. lbs. (30 Nm) on 1994-98 2.2L engines. On 1999 2.2L engines, tighten the brace retainers to 37 ft. lbs. On 1994 4.3L models tighten the retainers to 24 ft. lbs. (33 Nm). On 1995-99 4.3L models, tighten the retainers to 31 ft. lbs. (41 Nm).
  3. If removed, install the A/C compressor.
  4. If removed, install the filler tube and its retainer. Tighten the retainer to 15 ft. lbs. (20 Nm).
  5. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end.
When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  1. Properly install the drive belt and, if applicable, adjust the tension.
Be sure to secure any hoses which may get in the way or rub other components.
  1. Remove the caps, then connect the feed and return hoses to the pump.
  2. Properly refill and bleed the power steering system.
  3. Test drive the vehicle.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 08, 2012 | 1996 Chevrolet Blazer

2 Answers

I almost have the water pump off but there is one bolt that is behind the power steerng pulley that I can not remove. I was wondering how to remove the power steering pulley?


To remove the pulley wheel from the power steering pump you typically have to remove 3 bolts but to get to those 3 bolts you have to use a socket and go through the holes on the pulley itself.

Apr 30, 2011 | 1995 Buick Park Avenue

1 Answer

Repair power steering for 1994 Chevy S10 Blazer V-6, pump and houses.


Power Steering Pump Removal & Installation 2.2L Engine To Remove:
  1. Remove the upper cooling fan shroud.
  2. Position a fluid catch pan under the power steering pump.
  3. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan. NOTE: On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
  4. Remove the drive belt from the pulley.
  5. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump. NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
    Installing the pilot bolt 85388111.gif

    Removing the power steering pump pulley 85388113.gif

    Installing the power steering pump pulley 85388114.gif

  6. Unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  7. Remove the front mounting bolts and the rear bracket nuts from the studs on the engine.
  8. Remove the rear brace mounting bolt.
  9. Remove the power steering pump from the vehicle.
To Install:
  1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm).
  2. Install the rear bracket bolt and nuts. Tighten the retainers to 22 ft. lbs. (30 Nm) on 1994 - 97 models and 37 ft. lbs. (50 Nm) on 1998 and later models.
  3. Install the A/C compressor.
  4. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  5. Properly install the drive belt.
  6. Remove the caps, then connect the feed and return hoses to the pump.
  7. Properly refill and bleed the power steering system.
  8. Test drive the vehicle.
4.3L Engine To Remove:
  1. Remove the upper cooling fan shroud.
  2. Remove the drive belt.
  3. Remove the fan and clutch from the water pump.
  4. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.
  5. Safely raise and support the vehicle.
  6. Remove the shield from the steering linkage.
  7. Position a fluid catch pan under the power steering pump.
  8. Disconnect the return hose from the power steering pump, then drain the excess fluid into the catch pan.
  9. Safely lower the vehicle.
  10. Disconnect the pressure hose from the pump and cap the open line.
  11. Remove the filler neck tube.
  12. Remove the power steering pump mounting nuts and bolts.
  13. Remove the power steering pump from the vehicle.
NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
Installing the pilot bolt 85388111.gif

Removing the power steering pump pulley 85388113.gif

Installing the power steering pump pulley 85388114.gif

To Install:
  1. Position the pump to the vehicle.
    • Tighten the front retaining bolts to 37 ft. lbs. (50 Nm) and the nuts to 31 ft. lbs. (41 Nm).
  2. Install the filler neck tube.
    • Tighten the bolt to 15 ft. lbs. (20 Nm).
  3. Connect the pressure hose to the pump.
  4. Safely raise and support the vehicle.
  5. Connect the return hose to the vehicle.
  6. Install the shield on the steering linkage and lower the vehicle.
  7. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  8. Install the fan and clutch on the water pump.
  9. Properly install the drive belt. NOTE: Be sure to secure any hoses which may get in the way or rub other components.
  10. Install the upper fan shroud.
  11. Properly refill and bleed the power steering system.
  12. Test drive the vehicle.
prev.gif next.gif

Nov 05, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

What do i do to get new belt on


FOR THE 3.0L ENGINE IF YOU REPLACE AC BELT LOOSEN TOP IDLER PULLEY CENTER BOLT. IF YOU REPLACING ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTMENT BOLT AND PIVOT BOLT.IF REPLACING POWER STEERING PUMP BELT LOOSEN POWER STEERING PUMP ADJUSTMENT BOLT AND MOUNTING BOLTS.****** FOR THE 2.4L ENGINE TO REMOVE POWER STEERING BELT LOOSEN TOP IDLER PULLEY.FOR ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTER BOLT, PIVOT AND MOUNTING BOLTS.FOR AC COMPRESSOR LOOSEN LOWER IDLER PULLEY.

Oct 07, 2010 | 1996 Nissan Pickup

1 Answer

Removing power steering pump from v8 windsor


Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
  1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
  1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.





    Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).





    Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner
  1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .

    Remove the drive belt from the power steering pump pulley.
  1. Remove the oil dipstick tube.
  1. Remove the power steering pump support (3C511).
  1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
  1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).

    While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
  1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
Installation
  1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
  1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
  1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).

    Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
  1. Install the drive belt on the power steering pump pulley.
  1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
    On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
  1. Install the power steering pump support, if removed.
  1. Install the oil dipstick tube.
  1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
  1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
  1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
  1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .


    Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only





    Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
    (32-38 Lb-Ft)

    Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar





    Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8

Jun 09, 2010 | 1996 Ford Explorer

2 Answers

How do i replace the water pump in a 1994 buick lesabre?


Hi

Thanks for using FixYa. You’ll need to remove the power steering pump and pulley. Use a 13 mm socket and remove the two bolts that hold on the pump assembly. They are normal bolts that turn counter clockwise to remove. You don’t need to remove the pulley from the pump. Place your 13mm socket thru the holes in the pump to remove the two bolts.

When you remove the two bolts that hold the pump on, this will allow you just simply move the pump out of the way to remove water pump bolts


Please do rate the solution and revert for further assistance.


Thanks

Rylee

Oct 04, 2009 | 1994 Buick LeSabre

1 Answer

Now toremove power streeing pump



REMOVAL & INSTALLATION

See Figures 2, 3 and 4
  1. Position a fluid catch pan under the power steering pump.
  2. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan.

On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
  1. Remove the drive belt from the pulley.
  2. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.

When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.


0900c15280250684.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Installing the pilot bolt


0900c15280250685.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Removing the power steering pump pulley


0900c15280250686.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Installing the power steering pump pulley
  1. On most models, it may be necessary to unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  2. If equipped, unfasten the power steering filler tube bolt and remove the filler tube.
  3. Remove the rear brace retainers and the brace.
  4. Remove the power steering pump-to-bracket bolts and then remove the pump from the vehicle.

To install:
  1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm) 2.2L engines. (50 Nm). On 4.3L engines tighten the bolts to 37 ft. lbs. (50 Nm).
  2. If equipped, install the rear brace and tighten the retainers to 22 ft. lbs. (30 Nm) on 1994-98 2.2L engines. On 1999 2.2L engines, tighten the brace retainers to 37 ft. lbs. On 1994 4.3L models tighten the retainers to 24 ft. lbs. (33 Nm). On 1995-99 4.3L models, tighten the retainers to 31 ft. lbs. (41 Nm).
  3. If removed, install the A/C compressor.
  4. If removed, install the filler tube and its retainer. Tighten the retainer to 15 ft. lbs. (20 Nm).
  5. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end.

Jul 05, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

2000 monte carlo how to replace water pump.last bolt


there should be holes in power steering pump pulley that when positioned correctly the bole should go through one of those holes, if not then you have to remove the pump

Apr 29, 2009 | 2004 Chevrolet Monte Carlo

2 Answers

The power steering pump bolts all seem to have vibrated out, the unit came free and i can just move it around, the pulley moves freely, everything else seems to work ok


I don't have chrysler producs. I'll post 3.8L V6 Ford Windstar for reference. You'll get some idea.



Removal
ssw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP.
  1. Using a 15mm socket or wrench on bolt attaching drive belt tensioner pulley. Rotate drive belt tensioner (6B209) clockwise to remove drive belt from pulleys.

    3.8L Engine

    e973ba6.gif
Item Part Number Description 1 10300 Generator 2 3A674 Power Steering Pump 3 19703 A/C Compressor 4 6B217 Drive Belt Tensioner Pulley 5 6312 Crankshaft Pulley 6 8501 Water Pump 7 6B209 Drive Belt Tensioner 8 8620 Drive Belt
Installation
  1. Install drive belt over all pulleys (except drive belt tensioner ).
  1. Rotate drive belt tensioner as described under Removal and install drive belt over drive belt tensioner pulley. Ensure that all V-grooves make proper contact with pulleys
---------------------------------------------------------------
Another example
Pulley, Power Steering Pump CII
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Drain as much fluid as possible from the power steering pump (3A674) through the power steering oil reservoir (3A697) neck.
  1. Install Steering Pump Pulley Remover T69L-10300-B on the power steering pump pulley (3A733) , and place the tool and power steering pump in a vise by gripping the small hex-head of the tool.
  1. Hold the power steering pump , and rotate the tool nut counterclockwise to remove the power steering pump pulley . Do not apply in and out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.

Installation
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal thrust areas.
  1. Place the power steering pump pulley on the power steering pump shaft, and install Steering Pump Pulley Replacer T65P-3A733-C. The small diameter threads on the tool should be fully engaged in the power steering pump shaft.
  1. Hold the power steering pump , and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. The power steering pump pulley face must be flush within 0.25mm (0.010 inch) of the end of the power steering pump shaft.
  1. Remove the tool.
  1. Fill the power steering oil reservoir to the COLD FILL line.
------------------------------------------------------------------------------------------
Steering Pump, Power Removal
  1. Disconnect battery ground cable (14301) .
  1. Remove accessory drive belt (8620) .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove right front wheel (1007) and tire assembly.
  1. Remove power steering pump pulley (3A733) .
  1. Position drain pan. Remove power steering pressure hose (3A719) and power steering return hose (3A713) from power steering pump (3A674) .
  1. Remove four power steering pump retaining bolts (three in front, one in rear) and remove power steering pump .
Installation
  1. Position power steering pump and install retaining bolts. Tighten retaining bolts to 41-54 Nm (30-40 lb-ft).
  1. Install power steering pressure hose and power steering return hose to power steering pump . Remove drain pan.
  1. Press on power steering pump pulley as outlined in this section.
  1. Install right front wheel and tire assembly. Tighten lug nuts (1012) to 115-142 Nm (85-105 lb-ft).
  1. Lower vehicle.
  1. Install drive belt to power steering pump pulley .
  1. Connect battery ground cable .
  1. Fill power steering oil reservoir (3A697) to proper level. Refer to Section 11-00 .

    Power Steering Pump and Bracket, 3.8L

    17c7689.gif
Item Part Number Description 1 N607528-S2 Screw, M6-1 x 16 2 8509 Water Pump Pulley 3 W804804-S2 Screw, M8-1.25 x 35 4 N806214-S2 Bolt, M12 5 W606691-S36B Screw, M8-1.25 x 35 6 10B315 Generator Brace 7 N621939-S36B Nut, M8-1.0 8 10300 Generator 9 6B212 Accessory Drive Belt Tensioner Bracket 10 6049 Cylinder Head 11 19D624 Air Conditioning Compressor Bracket 12 W606563-S2 Bolt, M10-1.5 x 55 13 19703 A/C Compressor 14 N807273-S100 Bolt, M8-1.25 x 121.5 15 3C510 Power Steering Hose Bracket 16 3A674 Power Steering Pump 17 3C511 Power Steering Pump Support 18 W807239-S8 Bolt, M10-1.5 x 36.5 19 2888 A/C Compressor Brace 20 W806342-S2 Bolt, M8-1.25 x 23 21 W606571-S411 Bolt, M10-1.5 x 113.5 22 6C348 Idler Assembly 23 3A733 Power Steering Pump Pulley 24 N805137-S56 Bolt, M10-1.5 x 157 25 N621939-S2 Nut, M8-10 26 N807241-S36B Bolt, M10-1.5 x 132 27 6B209 Drive Belt Tensioner A — Tighten to 8-11 Nm (71-101 Lb-In) B — Tighten to 20-25 Nm (15-18 Lb-Ft) C — Tighten to 70-95 Nm (52-70 Lb-Ft) D — Tighten to 40-55 Nm (30-40 Lb-Ft) E — Press Flush with End of Power Steering Pump Shaft

Mar 03, 2009 | 1994 Plymouth Voyager

1 Answer

Water pump replace


Water Pump Replacement (3.8L)

Removal Procedure
  1. Drain the cooling system.
  2. Loosen the water pump pulley bolts.
  3. Remove the drive belt.
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    3. Remove the power steering pump and reposition.
    4. Remove the water pump bolts.
      1. Remove the water pump.
      2. Remove the water pump gasket.
      3. Clean and inspect the water pump mating surfaces.
      Installation Procedure
      1. Install the water pump gasket.
      2. Install the water pump.
        1. Notice: Refer to Fastener Notice in Service Precautions. Install the water pump bolts.
          • Tighten the long water pump bolts to 34 Nm (25 ft. lbs.) .
          • Tighten the short water pump bolts to 22 Nm (16 ft. lbs.) .
            1. Install the water pump pulley.
            2. Install the water pump pulley bolts.
              • Tighten the bolts to 13 Nm (115 inch lbs.) .
            1. Install the power steering pump.
            2. Install the drive belt.
            3. Fill the cooling system.
    5. The Whole Thing I Know You Didnt Want to hear that about The P/S Pump Thats why I Did More Reserch you seemed to Know what You are Doin They get the Best of us though Hope this Helps & RATE ME PLEASE

Feb 03, 2009 | 2005 Chevrolet Impala

Not finding what you are looking for?
1994 Ford Thunderbird Logo

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...