Question about 2001 Pontiac Montana

Open Question

I need to know the engine torque specs for a 2001 pontiac montana 3.4

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 393 Answers

SOURCE: Head bolt torque specs for 1992 Pontiac 3.1 ltr

the last time i did the same job the gasket kit had the specs inside the box. the parts store should have a book/reference manual

Posted on Dec 09, 2008

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

SOURCE: need torque specs for a 85 s10 chevy with a 2.5 engine?

here you go!

1dd4f4a.gif93a64e1.gif

Posted on Jun 21, 2009

  • 75 Answers

SOURCE: TORQUE SPECS /HEAD GASKET/2001 CAVALIER...

for the 2.2L OHV:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

for the 2.4l dohc are as follows:
(pully 9 3 1 5 7
side) 10 6 2 4 8
bolts 1-8 torqued to 65Nm (40ft/lb)
bolts 9-10 torqued to 40Nm (30ft/lb)

then (either engine) give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

Posted on May 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust valve lash on a 2001 pontiac montana 3400 enging


The lifters are hydraulic, so adjusting them is not possible. The lifters can take up very little play, so valve ticking when cold is normal. I have had two of these engines. Be sure to have the heads torqued properly, to keep play at a minimum.

Aug 31, 2014 | 2001 Pontiac Montana

1 Answer

I need to know torque specs and torque pattern for a 2001 head gasket on my 2001 sunfire


HINT: The "torque pattern" on ALL cylinder heads is start in the center and work your way toward the ends. The specifications below are "torque-to yield" or "torque angle" specs. When in doubt, about 65 Ft. Lbs. will work on pretty much ANY aluminum head. The main point is to get them EVEN to prevent warpage.


11_20_2011_2_46_10_pm.gif

Nov 20, 2011 | 2001 Pontiac Sunfire

1 Answer

How to change head gaskets 2000 montana


I can tell you step by step, but the best way is for you just to buy the repair manual from the auto supply store where you are going to get the parts for the repair. It will have torque specs that you need and other information that will be useful.

Mar 05, 2011 | 2000 Pontiac Montana

1 Answer

Hello I looking for intake manofold torque for my pontiac montana 2000


remember new head bolts also, torque to yeild bolts. i would recommend to get a service manual for torque specs and procidures for removal of heads. also head gaskets are leaking for a reason have heads checked for straightness and for cracks at local machine shop, keep all pushrods and rockers numbered for reassembly, pushpods are different and will cause major engine damage if mixed up.

Dec 14, 2010 | 2000 Pontiac Montana

1 Answer

I need to veiw the firing order for my 2001 montana with the 3.4 engine is 135 in the rear or in the front


1-2-3-4-5-6


1-3-5 Rear of engine

2-4-6 Front of engine

Vote for me if this helps, thanks.

Jun 24, 2010 | 2001 Pontiac Montana

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

1 Answer

Change an oil pan gasket on a montana


Go down to your parts dealer (hopefully Auto Zone :)) and get the gasket as well as oil and oil filter (unless you are going to use the old oil and have something to catch it in). Drain the oil. Remove the bolts on the oil pan. Remove it and the old gasket. Check to see that ALL of the old gasket has been removed. Clean the mating surfaces. Put new gasket in place on the pan and place to the block. Install bolts and tighten to specs. You can get the bolt torque specs from AZ as well. Add oil before starting engine

Mar 15, 2010 | 2002 Pontiac Montana

Not finding what you are looking for?
2001 Pontiac Montana Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...