Question about 2000 Audi A4

Open Question

How do I remove the glove box lid

Hinge is broken

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix the broken glove box on my 2006 Buick rendezvous


Thread Rendezvous Glove Box Door Hinge

Check this thread ... I might help ... I dont know the design of the glove box of your car, so cant provide a detail answer myself.

Sep 06, 2015 | Buick Cars & Trucks

1 Answer

How to open a glove box door when the latch is broken on


check under the glove box door to see if you can see the hinges. Sometimes you can unscrew the hinges from the bottom. Else you have to knock out the hinge pin on both hinges, open the door from the bottom and see if you can swing the door up to undo the latch.
If this does not work, cut a hole in the bottom ot the glove box, it is usually made of plastic or papier mache, release the latch from inside, then you can remove the plastic box once it is open and replace it with a new one. It will cost you, but it will be less expensive that breaking down the metal door!

Feb 21, 2015 | 1999 GMC Sierra

1 Answer

GMC Sierra 1500 Glove box latch is broken and will not open


Unfortunately, you cannot just by the latch assy from the dealer. They only carry the complete glove box assy. (cost $285). The best fix if you are near a truck salvage yard is to get one from a wrecked vehicle. I just fixed mine for $32.00 including tax. To remove the glove box, you will need to remove 3ea 7mm screws that hold the hinge to the dash. And there are 2ea alum pop rivets that you will need to drill out (I used a 3/8 drill bit). Then slide the assy to the left to free the tab on the right side. Reverse procedure to install.

Nov 14, 2012 | GMC Cars & Trucks

1 Answer

The catch on the glove box lid on a vw golf 2001 is broken how do i fix it?


You need to replace the whole glove box door. Pry the panel on the right side of the dash off, remove the t25 screw, remove the 3 t20 screws along the bottom of the glove box, and the t20 screws that you can see inside the glove box. This will loosen it enough to pull the whole glove box loose. Then you need to remove the damper by prying the little plastic pin out. Then remove the bracket it secures to that has a t20 screw in it. There are 2 plastic pins in the hinges that need to be popped out, once this is done, the door will come off. Reassembly is the reverse.
If the pins are difficult to reinstall, file the new glove box door hinge holes with a round file. I usually shoot a little oil into the damper too, just to make operation easier.

Feb 04, 2011 | 2001 Volkswagen Golf

1 Answer

Fuse box locations on a 2006 jeep wrangler 4.0 6speed manual


To access the fuse panel the glove box must be removed. It is removed by slipping the glove box strap off the hook and letting the door roll down off its hinges. To reinstall, position the glove box door at an 8 o’clock orientation, engage the hinge hook formations on the lower edge of the glove box door with the hinge pins on the lower edge of the instrument panel. Tilt the upper edge of the glove box door upward toward the instrument panel enough to reattach the glove box strap to the door. Rotate glove box door to closed position. Open and close to insure proper installation.

ed6951f.jpg

Also can download the 2006 TJ Wrangler - Owners Manual

Hope helps (remember rated this). Good luck.

Jul 16, 2010 | 2006 Jeep Wrangler

1 Answer

How do i remove the glove box on my dodge caravan 2001


open the glove box door, remove everything from inside the glove box. remove the clip retaining the door-stop strap. pivot the glove box downward,unsnap the hinges from the instrument panel and remove the glove box. install in the reverse manner.

Apr 11, 2010 | 2001 Dodge Grand Caravan

1 Answer

How do I change the cabin filter on my 2002 Honda Accord SE?


There are two filters.
You have the remove the glove box. Three screws on the bottom edge. Remove them, then open the glove box door. Three plastic covers along the top edge, remove with something that won't cut them up. Remove screws under them (two screws under the center one). Then, push the glove box hinges toward each other to disengage the clips in the dashboard. Then pull the glove box assembly down and out (when the box is part way out, disconnect the glove box light connector before you take it the rest of the way).
Once the glove box is out, remove the three screws (two on the right, one on the left) of the glove box reinforcement panel, then remove the panel (the bar looking thing next down from where you took the three screws out of the bottom of the glove box).
Release the snap at the bottom and remove the air conditioning filter lid.
Slide the upper and lower filter assemblies out of the evaporator housing.
Remove the old filters from the filter carriers, clean the carriers and inset the new filters.
Reverse procedure to install.
I know that this sound involved, but just take your time, and you can do it.
Hope this helps you.

Nov 08, 2009 | 2002 Honda Accord

2 Answers

How does glove box come off to replace air cabin filter ?


First, take a good look at what you’re doing.
Look on the right side of open glove box and locate a plastic lever. You will see grooves on the end connected to the glove box. The grooved area is the spot to place the thumb in order to press this lever off the glove box when it comes time to do that.
Look up under the glove box. You will see two brass colored screws one on each side of the bottom of the glove box. These screws go up through two square plastic hinges that are attached to the glove box and into the the dash frame.
Okay, with the glove box closed remove the two brass colored screws, and put them aside so you won’t lose them..
Open the glove box and hold the glove box with your left hand and press on the plastic lever (grooved area) located on the right side of the glove box. This lever (the lever already mentioned above) is slotted and will pop off the glove box.
Put the glove box carefully aside.
Look straight in behind the glove box. You will see a rectangular black plastic cover approximately 1.5 inches wide by 8 inches long. On the right and left side are arrows pointing in. Press the arrows and pull out on the cover. This will slide out the tray that holds the filter. Remove old filter and insert the new one, flow arrows pointing down.
Retrieve glove box, hold in place, and attach plastic plastic lever to the right side of the glove box. The reverse of removal.
Next, the two plastic hinges located on the bottom of the glove box fit underneath the dash frame.
While holding the glove box in place (the glove box latch may hold glove box in place while installing screws) re-install the two screws through the plastic hinges into the frame and tighten.
Hope this helps you.

Oct 30, 2009 | 2004 Honda Accord

3 Answers

How to replace the cabin air filter in a 2000 toyota avalon xls


lower the glove box and its forward of that, should be a plastic panel to remove.

Sep 23, 2009 | 2004 Toyota Avalon

1 Answer

Cabin filter element location


Filter is located behind the glove box. All you need is a screwdriver to replace.

1. Open the glove box and empty to take the weight off the box.

2. On the right side there is a plastic hinge like device held on by one Phillips head screw. If you have trouble removing with a Phillips screwdriver you can remove with a narrow flat head screwdriver. Remove the screw and slide hinge off the mount.

3. To drop the glove box press the sides slightly inwards while 'forcing' it open beyond it's normal stopping point. Careful as when it releases it will fall wide open and may even fall from its hinged area. Set it aside.

4. Behind the glove box there is probably some fiberous material inserted to prevent noise like squeaking when it rubs. It is sticky on one side to hold it in place. Just remove and place out of the way.

5. Behind the fiberous material there'll be a cover which kinda looks like a grille. Mine was white and it is in the center of the opening. Remove it by releasing the clips at the left or right. It comes right out.

6. When the cover comes off slide the filter out and replace it. The filter lays flat and just slides in and out easily. However, if it has been some time since you replaced be prepared for a lot of debris on top of the filter such as leaves, grass or other general type of debris that has been sucked into the filter. It also may be the source of any bad odors that you smell through the air conditioning system.

7. Reverse the process. Replace the cover and push the glove box lid back into place. When you replace the glove box be careful to make sure the hinge you initiallly removed the screw from is not left behind the glove box or you will have to remove again to get it out. Replace the screw and do not over tighten as it screws into plastic and then your done.

Apr 16, 2009 | 2006 Suzuki Grand Vitara

Not finding what you are looking for?
2000 Audi A4 Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...