Question about 2006 Mitsubishi Outlander

1 Answer

The front accessory socket on my 2003 mitsubishi outlander needs to be replaced. can i do it myself or do i have to take it to a shop?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 645 Answers

The what

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Show or explain how to replace cam sensor in 2003 mitsubishi outlander please?


How do you know the sensor needs replacing?

Was it looked at with a scan tool & component tested
& found to be bad?

Codes have nothing to do with replacing parts
They are used to diagnose the reason they are set

The internet has pictures of parts locations

That is a job for the the best of shops, to diagnose,
& actually find a problem

Jul 02, 2014 | 2003 Mitsubishi Outlander

1 Answer

How do I replace the headlight assembly MN133516


The 2003 Outlander utilizes replaceable (9007) headlight bulbs. If you're looking to replace the bulb(s);
1. Raise the hood.
2. Remove the plastic cover at the rear of the headlamp assembly by rotating it counterclockwise, and pulling it off. This will allow access to the headlight bulb.
3. Twist the bulb socket counterclockwise in order to remove it from the headlamp assembly. Pull the old bulb out of the socket, and use a clean cloth to install the replacement bulb. Do not touch the glass of the new bulb.
4. Place the socket back into the assembly, and twist it clockwise. Reattach the plastic cover, and close the hood.
Are you needing DIY instructions for replacing the entire headlamp assembly? Left (driver) or Right (passenger)?

Jan 18, 2013 | 2003 Mitsubishi Outlander

1 Answer

The outlander has no fuel filter and its a part of the fuel pump. When do I need to replace the fuel pump on my 2003 Mitsubishi Outlander?


Fuel pumps are not a regular maintenance item that needs to be changed at a certain time. Replace it only when it fails. The designers built that fuel filter into the tank with the reasoning that it will last as long as the fuel pump itself.

Jul 05, 2011 | 2003 Mitsubishi Outlander

1 Answer

2003 Mitsubishi Outlander power window repair. I


just repair the broken wire with heatshrink[after youve respliced it] and check operation of motor.if it works,make sure wiring is securely cabletied out of the way,when reassembled

Sep 12, 2010 | 2003 Mitsubishi Outlander

1 Answer

Replace front axle what tools are needed on a 2003 mitsubishi outlander i have a lot of noise from left ft i've had wheel bearing replaced and it's still has a lot of noise at speed when the wheels are...


wrenches. tire tool. hammer , pliers , a jackstand or blocks to support the vehicle. a jack to manipulate the lower control arm . air compressor and air impact wrench and a socket ( metric and usually a special size ) available at Auto zone for rent
which is refundable when you take it back ( so its free )
the sad part is that the driveshaft just pulls out of the transmission, and slips back in with a little effort. all held in place with 1 special nut. the bad part is that this PROCEDURE IS DANGEROUS because removing the lower balljoint lets the TENSION from the strut assembly FREE and can hurt you or even kill you. Please exercise caution. this task can be accomplished with minimal effort and a few tools.

Jul 31, 2010 | 2003 Mitsubishi Outlander

1 Answer

My accessory sockets (cigarette lighter) are not working on my 03 mitsubishi outlander, I checked the fuse box and they are all okay. Any suggestions?


It's fuse # 25 a 15 amp. There is a relay in this circuit and the ignition switch must be on or accessory. By the way, sometimes what you are trying to plug in just doesn't make good contact.

Dec 19, 2009 | 2003 Mitsubishi Outlander

1 Answer

My outlander 2003 mitsubishi accessory socket is not working what can i do


check the fuses, also check fuses in engine compartment, 99% of the time its just a fuse, good luck.

Dec 19, 2009 | 2003 Mitsubishi Outlander

2 Answers

Sholud I purchase a mitsubishi outlander 2003 with 103,291 miles on it for $8495


I have 150,000 miles, no problems. I think a front CV or bearing in in need of replacement. I have replaced the front brakes and rotors. Great on the highway.. 20MPG on the freeway..

Apr 27, 2009 | 2004 Mitsubishi Outlander

1 Answer

How do you alighn headlamp assyon a 03 mitsubishi


It takes special equipment that is expensive. Take it to the the dealer or a body shop.

Feb 20, 2009 | 2003 Mitsubishi Outlander

Not finding what you are looking for?
2006 Mitsubishi Outlander Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...