Question about 1997 Chrysler Cirrus

1 Answer

1997 chrysler cirrus alarm was set off. reset alarm with key and keyless entry but still no responce. the starter doesn't even click. checked all fuses, all good. toggled the valet system too, and no responce as well. Dealer told me to put key in ignition in the on position for an hour to an hour and a half so the computor would recognise that it is ok and that didn't help either. asked ther dealer if they had to plug into the vehicle ecm to reset it but they didn't say that they would have to do that.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 306 Answers

Sounds like an aftermarket alarm. if it is the try to remove the fuses from the unit. they will be located under the dash. if its a chrysler factory alarm try disconnecting the battery and let it sit for 5 minutes or so. that should reset everything

Posted on Feb 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset keyless door entry that is in lock out mode


Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/
Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics
20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

Jan 08, 2016 | Cars & Trucks

3 Answers

I lost the keys how do i open the trunk of my 2000 chrysler cirrus lxi


and chrysler dealer can make you new keys just take title and vin number in to them .

Aug 29, 2015 | Chrysler Cars & Trucks

1 Answer

2004 Hyundai Elantra won't start, emergency flashers keep blinking, can't shut off, lights dim, can't jump start, clicking from under dash from relays. What could it be?


The 'Keyless Entry & Burglar Alarm System" is activated. You must 'Disarm' the system using the Keyless Entry Remove (Key Fob) to "Reset" the system. The reason the engine won't start is due to the burglar alarm - it has a "Starter Kill" circuit which is activated when the alarm is activated. The alarm must be DEactivated to DEactivate the 'Starter Kill' circuit.
Another way to start the engine is to get in the car, put the key in the ignition and turn it to 'ON" and wait 3 to 5 minutes until the emergency flashers stop/turn off. Afterward, you should be able to start the engine. NOTE: This does NOT reset the burglar alarm. It will go off again when you enter the vehicle without using the remote/key fob.

Sep 06, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

Just replaced the crank sensor on my chrysler cirrus 1996. the factory alarm reset itself. i had previously turned it off. cut the volume wire so lights just blink and makes clinking noise. i can start the...


Thats not a factory alarm that aftermarket. go under the steering column and remove the whole alarm set up. or better yet find a relay that is attach to the starter signal (match the color) and restore how it used to be then you should be able to crank the car , if you sucessfull have bypass the alarm then go ahead and look for its ground and just cut it. The aftermarket cuts into the ignition switch starter signal so that is where you locate the starter relay alarm.

May 22, 2011 | 1996 Chrysler Cirrus

1 Answer

My mom lost her keyless entry remote. bought another online. i looked in the manuel and was unsuccessful in programming the new one. what steps must i take.


  1. 1 Press the lock button on your Chrysler remote five consecutive times at brief two second intervals.
  2. 2 Place your key in the car's ignition and turn it to the right two clicks to the "Run" position on all Chrysler cars.
  3. 3 Hold the unlock button. Then press and hold the panic button simultaneously. Release both buttons at the same time and you will hear a small beep to indicate that the programming is in effect.
  4. 4 Press and release both the lock and unlock buttons at the same time.
  5. 5 Turn the key to the off position and remove it from the ignition. Test your remote to see if the programming was successful.

Read more: How to Program a Chrysler Keyless Entry Remote ' eHow.com http://www.ehow.com/how_5014707_program-chrysler-keyless-entry-remote.html#ixzz1ANbOsavi

Jan 07, 2011 | 1998 Chrysler Cirrus

1 Answer

Looking to see whats wrong with my 1996 chrysler syruss need hel resetting the car alarm system.-AL


If you do not have the keyless entry key fob, you can use the key. Insert the key in the door, turn to unlock and hold. If this does not work try turning to the unlock position 2x with in 5 second (the same as unlocking all the doors from the driver's side).

Dec 23, 2010 | 1996 Chrysler Cirrus

2 Answers

My 2004 v6 ford explorer won't start new batery and new starter no luck wont even click ?


Did you check the start relay for voltage? Ohms reading?

If I remember correctly the circuit goes like this:
Key turns ignition switch which puts voltage to the start relay which engages the solenoid.
So if it isn't even clicking and your headlights seem to be working fine then it is either the ignition switch or the start solenoid coil.
On older Fords the start solenoid used to be remote mounted on a fender. I heard newer Ford vehicles had it integrated with the starter like GM does.
A quick visual inspection will tell you which and where you need to look.
You might check if there is a fuse for that as well.

Apr 01, 2010 | 2004 Ford Explorer

2 Answers

Lost keyless entry remote


The fuse for the alarm is under the hood. Give a good look and you should find it. Once you have pulled it it will deactivate the alarm I am not sure if this is exactly your problem since you said that the car wont start.... but it is worth a try.

Aug 23, 2008 | 1997 Chrysler LHS

Not finding what you are looking for?
1997 Chrysler Cirrus Logo

585 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...