Question about 1995 Mazda Millenia

1 Answer

Have a 95 mellinia s and it doesnt start.it tries and started for an instant but died.was told it might be cam or crankshaft sensors but dont know where their located.i messed up the starter trying to start it and it spins but doesnt turn engine.i bench test it and it turns and kicks out so is it the solenoid?

Posted by on

  • jbas1 Feb 05, 2010

    it doesnt kick out when its installed on the car only when i bench test it

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 306 Answers

If the starter kicks out and spins then it sounds like you have done damage to the flywheel

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 Pontiac Grand Am GT V6 just died wont start? starter is good, dont know if alternator or what?


If the engine will not crank, and the battery is fully charged, the only thing in play is the starter circuit. The ignition and alternator do not get involved until after the engine is started.
If the engine died and will not crank, you would need to check for voltage at the starter with the key switch in the start position.
You may need a manual with wiring diagrams to trace the circuits.

Jan 28, 2013 | Cars & Trucks

1 Answer

Our 2000 xterra stalled out while driving and wont stay started now. anyone know whats wrong?


either crankshaft postion sensor camshaft postion sensor sometimes tho cars just have a crank sensor and it does the cam sensor job to

Jan 14, 2013 | 2000 Nissan Xterra

2 Answers

Troubleshooting the cam and crank sensors


These are a well known failure point for this vehicle and engine. They are currently on there third redesign to help solve the frequent failures.

the first thing to do is see if there are any trouble codes in the computer. If you see P0340

Jan 18, 2012 | Nissan Sentra Cars & Trucks

2 Answers

1993 s10 4.3 starts fine, while idling it dies. sometimes i have a hard time restarting. the blazer died a couple of times while driving.fuel pump is good, tuned up, remanuf. injectors 1 yr ago,engine lite...


only half way there if you have a tbi check the crank sensor/ cam sensor that is the first line of business on that truck if the crankshaft sensor fails the truck stops dead when you wait a few minutes the sensor re energizes and the truck will work again for a bit antiknock can cause similer problems but not while the truck is running

Feb 24, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

My car wont start


It is located on the outside of the engine near the camshaft. It is basically a small electronic gadget that has to touch the cam shft to read info and feed it to the computer. Are you recieving any fuel ? There could be other things that can be the problem not nessesarily the camshft sensor.... ie. the idle position sensor, the egr valve, the crankshaft sensor ,etc.

Jan 01, 2010 | 1995 Chevrolet Cavalier

1 Answer

Car starts then instantly dies


there is an idle control valve and an air flow meter that should be checked.check all the wiring harness and connectors to the crank and cam sensors.

Sep 15, 2009 | 1994 Eagle Talon

3 Answers

95 Olds 88 dies


I would replace the crankshaft position sensor AKA CPS

Sep 21, 2008 | 1995 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1995 Mazda Millenia Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...