Question about Lincoln Town Car

2 Answers

I am trying to use the keyless entry on this vehicle also I have purchased a second remot for this same vehicle and to program the remote Im told that I need to go through the keyless entry process

Posted by on

  • chertnt Feb 05, 2010

    I have recieved you comment, my original problem was that I do not have the permanent code it has been removed prior to me obtaining this vehicle is there any way to obtain the code for this vehicle thanks

    chertnt

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 17,970 Answers

F

To program a transmitter:

1. Enter the five-digit permanent code into keyless entry keypad. (Factory code found on the module).

  • Within five seconds, press 1/2 switch.
  • Within five seconds, press any button on the first transmitter. The locks will cycle to confirm successful programming.
  • Within five seconds, press any button on the second transmitter.
  • Repeat step c for each additional transmitter (up to four total).
  • Press 7/8 and 9/0 together to end the programming session or wait more than 7.5 seconds.

To program an alternate code:
1. Enter the five digit permanent entry code into keyless entry keypad.
2. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code. (Factory code found on the module).
3. Enter any alternate five digit code within five seconds of pressing 1/2 button.
* Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
9/0-- no memory recall
1/2-- memory seat position 1
314-- memory seat position 2
5/6-- memory seat position 3
* After successful programming, the doors will signal by locking and then unlocking.

The Keyless Entry Module is located inside the drivers side door.

Hope thats help.

Posted on Feb 05, 2010

  • ZJ Limited
    ZJ Limited Feb 05, 2010

    Hi chertnt

    Its not possible; I have the same problem with my Explorer, and the old owner lost the owners manual (in there, lasta page, have the code). The only solution for this problem is visit your dealer and take the factory code from they.


  • ZJ Limited
    ZJ Limited Feb 05, 2010

    Also, maybe can try with this, to program the Lincoln Town Car FOB (remote) you first need all the remotes you want to work with that car:
    1) Put the key in the ignition.

    2) Turn the key on till the dash gauges light up. Here's the trick: you
    need to turn the key from OFF to ON 3 times very quickly! You will know
    you done this correctly if your door locks lock and unlock by
    themselves.
    3) Once you hear the door locks cycle, you need to
    push the lock button on your remote or remotes if you have more than
    one. You should see the locks working from the remote at this time.


    Note: It is necessary to program all remotes to this vehicle at the
    same time, because any remotes that have been programed to this vehicle
    in the past will no longer work!

    You only have a short time before the program mode of the vehicle resets, so be ready.

    That's it, you just take out the key and you're done.


×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

To program a transmitter:

  1. Enter the five-digit permanent code into keyless entry keypad. (Factory code found on the module).
    • Within five seconds, press 1/2 switch.
    • Within five seconds, press any button on the first transmitter. The locks will cycle to confirm successful programming.
    • Within five seconds, press any button on the second transmitter.
    • Repeat step c for each additional transmitter (up to four total).
    • Press 7/8 and 9/0 together to end the programming session or wait more than 7.5 seconds.
To program an alternate code:
  1. Enter the five digit permanent entry code into keyless entry keypad.
  2. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code. (Factory code found on the module).
  3. Enter any alternate five digit code within five seconds of pressing 1/2 button.
    • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code: 9/0-- no memory recall
      1/2-- memory seat position 1
      314-- memory seat position 2
      5/6-- memory seat position 3
    • After successful programming, the doors will signal by locking and then unlocking.

The Keyless Entry Module is located inside the drivers side door.
http://www.lincolnsonline.com/tech/00068.html

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 crown vic keyfob only works with ignition in run position .keyless entry and door locks work fine.even tried new keyfob.no change


The keyless entry system consists of the following components:
  • driver door module (DDM)
  • keyless entry transmitter
  • keyless entry keypad
The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
  • Battery junction box (BJB) fuses:
    • circuit breaker 7 (20A)
  • Central junction box (CJB)
    • 4 (10A)
    • 6 (15A)
    • 8 (25A)
    • 13 (5A)
  • Keyless entry keypad switch
  • Power door lock actuator
  • Luggage compartment release switch
  • Luggage compartment release solenoid
  • Connectors or connections
  • Wiring harness
  • If fuse's good have checked for DTC'S - diagnostic trouble codes .
  • B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .
  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter not programmed.
  • Remote transmitter.
  • DDM.
  • Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.
  1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.
  1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
  1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

Feb 19, 2017 | Cars & Trucks

1 Answer

I went through programing as far as lock recycling but wont go any further


Remote Transmitter Programming NOTE: All keyless entry remote transmitters must be programmed at the same time.
NOTE: Programming (or reprogramming) the keyless entry remote transmitters into the central security module can be accomplished using a diagnostic tool or by carrying out the following steps.
  1. Turn the ignition switch from OFF to RUN eight times within 10 seconds, ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after Step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the doors will lock and unlock one last time to confirm.

Mar 18, 2016 | 2004 Ford F150

1 Answer

2004 Suzuki Gran Vitara Keyless entry


Try this

2004 XL7

1. Remove key from ignition switch.

2. Close all doors.

3. Open drivers door

4. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

5. Within 20 seconds Close and open drivers door 3 times.

6. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

7. Locks should now lock and unlock automatically to confirm you
have entered programming mode.

8. Press the UNLOCK button on remote and locks should cycle to
confirm programming.

9. Repeat step 8 on each additional remote.

10. Exit vehicle with keys and remote, close door test remote(s)

Jun 01, 2014 | 2007 Suzuki XL-7

1 Answer

How to program keyless entry remote for buick lacrosse?


I own a 2007 Buick Lacrosse, but I imported it to Paraguay, South America. Now I bought a new Engine Start Keyless Entry Remote from Amazon, but here we do not have any GM dealer to program the unit.
I really need help to program the keyless remote control, I will appreciate very much your help.

Jan 02, 2012 | 2005 Buick LaCrosse

1 Answer

How do you prgram remote keyless entry


Here are the instructions from the factory service manual:
1. Enter 5-digit permanent entry code into the keyless entry keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.

3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.

4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).

5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.

Sep 14, 2011 | 1995 Ford Crown Victoria

3 Answers

MY PT Cruiser Functional transmitter and the one to be programmed both have no "PANIC" Button . How I programme the spare Fob


If you don't have the Panic button then sorry, you can't program yourself, the dealer will have to program it to the RKE (Remote Keyless Entry) module in the vehicle, using their DRB scan tool.

Sep 05, 2010 | 2001 Chrysler PT Cruiser

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

2 Answers

Keyless entry remote quit working. Just purchased new battery. Now Spare remote does not work either.


Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Jun 17, 2009 | 2000 GMC Sierra

1 Answer

Can't program Second remote to my Ford Explorer 99


reading your post you mention to "open and close switch"..not sure what refering to...these are the instructions from your vehicles service manual...good luck!

Programming NOTE: All keyless entry remote transmitters (15K601) are programmable and must be set at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Diagnosis and Testing.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 08, 2009 | 1993 Ford Explorer Limited

1 Answer

We purchased a 03 lincoln lsand need to reset the keyless entry


1. Sit in the vehicle driver's seat.
2. Remove the ignition key from the ignition lock cylinder.
3. Close all of the vehicle's doors.
4. Remove the MALL PGM fuse from the fuse panel. Or reset the fuse which controls your keyless remote.
5. Turn the ignition lock cylinder to the ACC position.
6. Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
7. Open and then close any vehicle door. You will hear a chime when the
remote control door lock receiver enters the programming/diagnostic mode. If
you do not hear a chime, start again at step 1.

This is an important fact here:

After 7 seconds, you may hear a chime confirming successful synchronization.
After approximately 14 seconds, you will hear a chime confirming successful
programming.

8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for
14 seconds.
9. Repeat step 8 in order to program each additional transmitter.
10. Remove the ignition key from the ignition lock cylinder.
11. Install the MALL PGM fuse back into the fuse panel.

This is important as well:
Once the keyless entry receiver enters the programming/diagnostic mode, the
programming of the first transmitter erases all previous transmitter
programming information. You must then program all of the transmitters.
Program only 1 vehicle remote control door lock receiver at a time. If you
program multiple receivers simultaneously, the same transmitter could
possibly be programmed to more than 1 remote control door lock receiver

The fuse should be in your fuse block of your vehicle.

May 25, 2009 | 2003 Lincoln LS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...