Question about 1992 Honda Accord

1 Answer

What Would Make The Wire To A Gas Peddle Melt

The Wire For The Gas Peddle Melted Why Would It Do That

Posted by on

  • Shea Jones May 11, 2010

    is anything else melted? your tranny could be getting hot.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Shorted or old wiring

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001Mercedes E320. Drives fine until I take my foot off gas peddle the car is still running but gas peddle does not work turn off then on runs fine until I take my foot off the peddle what is happing


If you have drive by wire. I would check the TPS first. It's under the gas pedal. (bad location). Unplug it and plug it back it. (bad connection) see if it still does it. If so. Have the codes read. I replace a lot of these because of the location. Bad water and moisture source.

Jun 21, 2015 | Cars & Trucks

1 Answer

2000 escalade thin plume of smoke by steering wheel, smell of burning wire, car stalled and now rpm gauge doesn't work.


Disconnect neg battery terminal take column apart and look for melted wires and what caused them to melt.

May 07, 2015 | 2000 Cadillac Escalade

1 Answer

2005 nissan sentra brake lights not working blows fuse when brake peddle pressed. i put a fuse in and when i press the peddle the fuse blows is this the switch that needs to be replace or the ascd


have a look at the fuse. If its all black and you see small bits inside you have a dead short in the circuit. Check the wiring for any metal to wire contact, especially at any points where wires touch any metal. If its just melted in the middle but did not blow violently its overloads the circuit is drawing too much current for too long, look for fused contact or stuck relay etc.

Feb 18, 2015 | 2005 Nissan Sentra SE-R

1 Answer

Melted egr pressure transducer and blowing vaccume lines off


The hot exhaust gas is coming up thru the EGR valve.
It probably needs to be replaced with a new sensor.

Feb 16, 2013 | Cars & Trucks

2 Answers

Drive vehicle down the road for 20 minutes and come to a stoplight engine stops when you take foot off gas peddle and go to apply brake. To keep vehicle from dying you have to hold the gas peddle down


Have you changed the timing belt? or timing belt guides? How many miles? This does not necessarily have to do with fuel.... Could have to do with air intake or timing as well....

Jun 12, 2012 | 1996 Dodge Ram

2 Answers

I have a 2003 ford windstar and the wiper wire harness melted any ideas if the computer would cause this


No the computer would not cause this. Wires only melt when the power being forced through them is more than the wire can handle. The excessive power draw is caused by a short or a bad motor with improper fuse protection.

Feb 03, 2011 | Ford Windstar Cars & Trucks

1 Answer

I have 2005 colorado, fan motor is good, put a new motor resitor in and it still wont work.


Check the fan select switch and the wire harness that plugs into it,it may need to be replaced,they will melt down.Also if the resister wire harness has melted,replace it also,and check the relay and fuse.

Dec 22, 2010 | 2005 Chevrolet Colorado

1 Answer

Hi i have a 2000 1.6 astra van which melted a piston running on lpg i now have engine repaired but wondering why it done this! does the lpg unit need calibrated and does anybody know wat it would cost? any...


A melted piston can come from many different reasons. It could have been a (1) bad head gasket, and coolant being introduced into the cyl. (2) Low coolant and the piston being one of the center 2 pistons, in this case it will over heat. LPG gas usually runs cooler that reg. gas and would have to be running very lean to burn the top or cause a melt down. LPG systems are very easy to adjust, and the computer should handle most of the adj. alone. Did a shop repair your engine? They should have given you some reason for the melt down. If you suspect your fuel delivery system is out of calibration have it checked buy the best you can find, as for a cost I think you are looking at $180 to $240 depending on how proficient they are on the system. You may have to pay a bit for their learning curve.

Jan 17, 2010 | 2003 Volkswagen Eurovan

1 Answer

Switch and wire melted


you need to use a heavy gauge wire and a higher amp switch be prepared for a switch to cost you any were from $25-75

Apr 20, 2009 | 1987 Mercury Lynx

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...