Question about 2006 Chrysler PT Cruiser

1 Answer

Haw to remove stering will, it is loose - 2006 Chrysler PT Cruiser

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Look on the back of the steering wheel for 2 to 4 screws, those will remove the airbag/horn pad and you should see a 19-24 mm bolt also try SAE sizes too.

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a lock cylinder for a 1991 chevy caprice?


need same tool first remove horn pad then stering wheel remove stering lock ring remove direccional switch then remove cylinder

Oct 18, 2014 | 1991 Chevrolet Caprice

1 Answer

Power stering making roring nois


Low fluid level or loose, worn belt or internal pump parts, bearings worn.

Oct 04, 2014 | 2001 Chevrolet Cavalier

1 Answer

Haw to finde the colors of steree cables instalation for my terrano


The colours are not of importance as you can test for power and earth using a multimeter or test light. Those wires with low voltage or no light are probably speakers which can be randomly connected until you get sound then use the fader and balance controls to figure out which speakers are which.

May 01, 2014 | 1994 Nissan Pathfinder

2 Answers

How to change the power steering fluid on a 2003 carvan


remove the power stering return line and place the loose end in a bucket and start the engine then keep adding power stering fluid to the resavore intill clean fluid runs from the return line the reinstall the return line and top off the resavore

Nov 10, 2011 | 2003 Dodge Caravan

1 Answer

Loose tilt steering


if your not mechanicly inclined you may want to have someone do the job for you, remove stering wheel and turnsignal switch under all that are 4 boltz that need to be tightened. usualy a 7mm socket 1/4 in drive should do the job

Jan 22, 2011 | 1988 Dodge Dynasty

1 Answer

How do u remove the stering wheel from a dodge 15oo to replace the whipper control


Disarm the Supplemental RestraintSystem (SRS) (airbag) Remove the airbag assembly. Partially remove the steering wheel retaining bolt. Leave the bolt in the column to push on it. Install a steering wheel puller.(Available at almost any parts store) Remove steering wheel puller, steering wheel and bolt once steering wheel has popped loose from the steering shaft.

Dec 20, 2010 | 2004 Dodge Ram

1 Answer

How to remove CV Joints on a dodge stratus


REMOVE your whelland tire on the side that you want to make to fix, removed your brake caliper and attach it with a piece of wire to the suspention strut ,remove the part that hold the caliper,remove the bolt or the nut that hold the lower balljoint in your lower suspention arm to your stering kuckle,and separate those two parts with a long pry-bar or a suspention fork and hammer,remove your disc brake,loose the spindle nut from the axle(this big nut is in the center of whell and if you are not working witch an air impact tool loose it right after removing your whell cap before removing the whell this is a high torque on it be sure to tight it correcly when yuo ins tall it)and pull the suspension strut foward you to removed the axle from the stering kuckle take apry-bar put it betwen the transmission and axle and pry it out some trans mission fluid may leak installation is reverse.

Mar 08, 2010 | 1997 Dodge Stratus

1 Answer

The steering collum is loose.


you need to get a new steering column in there asap. i had one do that to me and it ended up breaking on me

Feb 21, 2009 | 1991 GMC Sonoma

1 Answer

Power Srering


I have the same problem, I will know what to do november 19 2008, after the Saturn dealer will troubleshoot what it's faulty exactly. So Stand by

Sep 15, 2008 | 2005 Saturn ION

1 Answer

Stering pump ? for 1993 jeep cherokee 4.0 .


Loosen 2 pivot bolts on back of pump, 13mm. then loose one bolt on bottom/front. Turn adjustment bolt on right side/bottom of pump to loosen belt. Once belt if off, remove all of the bolts connection pump to engine bracket. Remove hoses going to pump. Install new one, filled up with fluid. Now you have to bleed air out of sys. Move steering wheel left/right to the stops. Do this about 10 times either direction.

Aug 06, 2008 | 1993 Jeep Cherokee Country

Not finding what you are looking for?
2006 Chrysler PT Cruiser Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...