Question about 2002 Nissan Maxima

1 Answer

Need help getting the front hub assembly and bearing off

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 617 Answers

Undo wheel, axle nut, 2 or 3 bolts behind , most have to be pressed on/off

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a front wheel bearing on a 2007 toyota tacoma 2 wheel drive pickup truck


The bearing & hub is a whole assembly for this model, start by removing the brake calipers, the removing the rotors" a couple taps with the hammer should loosen it" , after removing the rotors the hub & bearing assembly is held on by 4 #17 bolts, after you get the hud and bearing assembly off you will need a tool called a bearing split plate ,to split the hub and bearing off each other. Now you should have the new bearing assembly ,inner wheel seal, and hub set together" this is when you need a press". Press the hub onto the new bearing assembly.And thats it! Its ready to go back on the way you took it off.

Mar 02, 2013 | Cars & Trucks

1 Answer

How do i pull the hub off my 2002 mazda , on drivers side front


REMOVAL & INSTALLATION Except Miata FRONT
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel

Jan 01, 2011 | 2002 Mazda Protege

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

I have a chrysler lhs 1994 with a bad front wheel bearing and i need instruction on repair


These are the steps you need to follow for this procedure if you have the proper tools.
  1. Remove front caliper assembly and rotor from the steering knuckle as outlined under "Caliper, Replace" in the "Disc Brake" unit repair section.
  2. Remove hub and bearing to stub axle retaining nut.
  3. Disconnect hub bolts then remove hub and bearing assembly from steering knuckle by sliding it straight off end of stub axle. If metal seal on hub and bearing assembly is seized to steering knuckle and becomes dislodged on hub and bearing assembly during removal, or when removing hub and bearing, the finger disc on hub becomes damaged, hub and bearing assembly must be replaced.
  4. If hub and bearing will not slide out of knuckle, insert a prybar between hub and steering knuckle and gently pry hub and bearing from knuckle.
  5. Tighten stub shaft nut, lower vehicle and with brakes applied, torque stub shaft nut to 70 - 90 ft. lbs.

Aug 27, 2010 | 1994 Chrysler LHS

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

1 Answer

Replace front hub assembly.


Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

May 19, 2010 | 2003 Chevrolet Impala

1 Answer

2004 silverado 4x4 2500 left front wheel bearing


  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Jan 19, 2010 | 2004 Chevrolet Silverado 2500 Crew Cab

1 Answer

NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING


Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

May 19, 2009 | 1996 Saturn SL

1 Answer

Need help replacing front hub


Here's the steps....getting some pics for you....hang on a minute or two.

Front Hub Removal & Installation To Remove:
  1. Remove steering knuckle.
  2. Using a suitable slap hammer, remove wheel hub assembly.
  3. Using a suitable bearing press, remove outer bearing, oil seal, outer bearing race and preload spacer.
  4. Remove inner oil seal, inner wheel bearing and inner bearing race.
NOTE: It is not necessary to remove dust cover (back plate).
To Install:
  1. Using a suitable bearing press, install bearing races in steering knuckle.
  2. Pack the bearings and hub area with lithium grease.
  3. Install inner bearing in steering knuckle.
  4. Lubricate lip of NEW inner seal and press seal into knuckle.
  5. Install preload spacer into bore.
  6. Install outer bearing into bore.
  7. Lubricate lip of NEW outer seal and press seal into knuckle.
  8. Using an appropriate tool, support inner wheel bearing and press wheel hub into knuckle with a force of 2500kg.
  9. Install NEW inner seal.
  10. Install knuckle assembly.

May 13, 2009 | 2004 Kia Rio

Not finding what you are looking for?
2002 Nissan Maxima Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...