Question about Mazda B2600

1 Answer

I want to change pan gasket having problems removing pan steering column is in the way

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,857 Answers

Need to know the engine and year of truck to see if any removal procedures are in my information.

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change my oil pan gasket on my 95 ford Thunderbird, thank you first time car owner


Lift your car and place on jack stands. Then drain engine oil from pan. If there is/are any other steering or suspension components under oil pan, remove these first. Then, begin removing all bolts that hold pan in place. There should be a few bolts that come from the rear of the transmission section that also hold engine oil pan. Remove these. Once all bolts are removed, use a rubber mallet to tap oil pan until is breaks loose. If hard to remove, use a pry bar or flat head screw driver to pry oil pan off. Install in reverse order.

Dec 30, 2016 | Ford Cars & Trucks

1 Answer

Removing steering column shroud on a 2006 sierra 3500, no screws where videos show to remove them there's a recess area but no screws in the locations indicated


Steering Column Trim Cover Replacement

Important: You must check for 2 pan head tapping screws (1,2) in the lower trim cover before removal.
If necessary, remove the 2 pan head tapping screws (1,2) from the lower trim cover (3). Remove the lower trim cover (3).
If screws are not present in the lower trim cover, proceed to the next step.
Gently unsnap the lower trim cover from the upper trim cover.

Important: You must check for 1 TORX® head screw (1) in the upper trim cover (2) before removal.
If necessary, remove 1 TORX® head screw (1) from the upper trim cover (2).
If a screw is not present, remove the upper trim cover (2).

Dec 01, 2016 | 2006 GMC Sierra 3500

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

Im trying. To use a 91 ford t bird. 5.0 in to a 65 mustang but this engine. Has two humps in the oil pan and it hits the steering linkage can I che the pan for a one that has one hump?


OIL PAN WOULD BE HARD TO INTERCHANGE.PROBABLY WOULD HAVE TO CHANGE WHOLE STEERING COLUMN AND STEERING SYSTEM.OR BEST TO TRY A DIFFERENT ENGINE.YOU NEED TO LOOK AT OLDER ENGINE FROM 1965 TO 1970S MODELS.

Apr 26, 2011 | Ford Mustang Cars & Trucks

2 Answers

How can I change the transmision fluid in my 2005 chevy equinox?


Most transmission pans do not have a drain plug. To drain the transmission the velicle will have to be raised. I usually set a large drain pan-several quarts in size-under a rear corner of the transmission pan. I loosen about three bolts on the corner so the transmission fluid will drain. When drained, I remove the rest of the bolts-all 32 or more of them. With the pan off check the color of the fluid look for burnt looking fluid. See if the fluid smells burnt. If so you may have other transmission problems. Look for metal pieces in the transmission pan another indicator of other problems. Clean all the old gasket from the pan and transmission housing-be careful not to gouge either the pan or housing. I use my finger or thumbnail if possible. Gouging either of these places will cause leaks. If you're going to replace the screen do so now. Place the new pan gasket on the pan. Check with the manufacturer's specs before using any permatex or other silicones to hold the pan gasket. I always slide a bolt or two through the pan and gasket holes, lift the pan, and start the bolts. Go slow. Make sure each bolt is going through the gasket hole before tightening it to the transmission housing. Replace the bolts and tighten to a snug using a criss-cross pattern. Go back and forth across the pan tightening each bolt a few turns until all are tight. Don't overtighten the bolts. Doing so will damage the pan gasket, When all bolts are tight, refill the transmisson slowly checking for leaks. Fill the transmission to manufacturer's specifications.

Feb 26, 2011 | Chevrolet Equinox Cars & Trucks

1 Answer

I need to install my cruise control switch on my steering wheel . How do I go about removing the back cover on the steering wheel?


Removal & Installataion
  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
  4. Remove the air bag module from the steering wheel.
  5. Remove the steering wheel.
ca4e20e.gif
Exploded view of the shroud-type steering column showing shrouds, wiring and multifunction switch that includes the headlamp function

    1. Remove the upper and lower steering wheel trim covers using the following procedure.
    2. Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
    1. Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
    2. Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
    To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.
    1. Disable the SIR system.
    2. Remove the upper and lower trim covers.
    3. Remove the knee bolster.
      NOTE The abrasion sleeve located on the steering column wire harness assembly must be reinstalled. Make note of what connector is coming out of the abrasion sleeve for installation purposes.

    4. Remove the wire harness assembly from the wire harness strap.
    5. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector.
    6. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
    7. Remove the 2 pan head tapping screws and from the turn signal and multifunction switch assembly.
    8. Remove the turn signal and multifunction switch assembly from the steering column tilt head assembly.
    To install:
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    CAUTION Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.

    CAUTION The abrasion sleeve must be installed back onto the steering column wire harness assembly. The ignition lock cylinder case wires and connector must be hanging out of the middle of the abrasion sleeve.

    1. To install, reverse removal procedure.
    2. Tighten the following to specification.
      • Top pan head tapping screw: 27 inch lbs. (3 Nm).
      • Side pan head tapping screw: 62 inch lbs. (7 Nm).
    CAUTION When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling . Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

    Dec 08, 2009 | 2005 Chevrolet Impala

    2 Answers

    How do you change oil pan gasket


    have car jacked up and blocked for safety,drain oil from engine and remove the oil pan bolts,remove pan.

    Nov 23, 2009 | 1996 Honda Accord

    1 Answer

    Changing oil pan gasket on 1989 Ford Aerostar


    drain the oil from the pan and remove the filter.
    Lift the car up and secure it . So it will not roll or fall. Remove the bolts from the pan using a 10 mm or so and a rachet and small extension. There are several bolts all around the pan. Remove the pan and remove the gasket. Clean up the pan and remove all gasket material from the pan. Install the new gasket around the pan and replace back.

    Apr 05, 2009 | 1989 Ford Aerostar Cargo

    1 Answer

    Do you have pictures of the parts that need to be removed in order to change the oil pan gasket?


    Section 03-01: Engine, 4.6L (4V) 1997 Continental Workshop Manual IN-VEHICLE SERVICE Oil Pan/Oil Pump Screen Cover and Tube Removal
    1. Turn rear suspension leveler compressor switch (5K761) off (located in luggage compartment).
    1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    1. Remove oil level dipstick (6750).
    1. Raise vehicle on hoist.
    1. Remove dual converter Y pipe (5F250). Refer to Section 09-00 .
    1. Drain engine oil from crankcase.
    1. Disconnect engine control sensor wiring (12A581) from the low oil level sensor connector.
    1. Remove the power steering pressure hose retainer brackets from the engine front cover studs (two places). Position the power steering pressure hose (3A719) out of the way.
    1. Remove 16 bolts retaining oil pan (6675) to cylinder blocks (6010) and remove oil pan and oil pan gasket (6710).
    1. Remove two bolts retaining oil pump screen cover and tube (6622) to oil pump (6600).
    1. Remove bolt retaining oil pump screen and cover and tube support brace to main bearing stud spacer.
    1. Remove oil pump screen cover and tube. Discard O-ring.

    2. 02d437f.gif

        Item Part Number Description 1 W701240 Bolt (16 Req'd) 2 6675 Oil Pan 3 6622 Oil Pump Screen Cover and Tube 4 6010 Cylinder Blocks 5 6710 Oil Pan Gasket A — Tighten to 20 Nm (14 Lb-Ft), then rotate 60 degrees clockwise
          Installation
          1. Inspect oil pump screen cover and tube and replace if necessary.
          1. Position oil pump screen cover and tube on oil pump with a new O-ring and hand-start two bolts.
          1. Install bolt retaining oil pump screen cover and tube to main bearing stud spacer finger-tight.
          1. Tighten oil pump screen cover and tube-to-oil pump bolts to 8-12 Nm (71-106 lb-in). Tighten oil pump screen cover and tube to main bearing stud spacer bolt to 20-30 Nm (15-22 lb-ft).
          1. Clean oil pan and inspect for damage.
          1. Clean sealing surfaces of engine front cover (6019) and cylinder blocks with a clean cloth. If scraping is required, only use plastic-tipped scrapers to prevent damaging the aluminum sealing surfaces.
          1. Position new oil pan gasket on oil pan.
          1. Apply Silicone Gasket and Sealant F6AZ-19562-AA or equivalent meeting Ford specification WSE-M4G323-A6 where engine front cover meets cylinder blocks and crankshaft rear oil seal retainer meets cylinder blocks. Position oil pan on cylinder blocks and install 16 bolts. Tighten bolts in sequence to 20 Nm (14 lb-ft), then rotate an additional 60 degrees clockwise.

        Apr 03, 2009 | 1997 Lincoln Continental

        1 Answer

        How to take off steering wheel.


        1. Disconnect the negative battery cable.
        If necessary for access or service remove the steering wheel. Except for on 1967-69 simulated wood wheels, be sure to use a steering wheel puller.
        1. Remove the nut/bolt from the upper intermediate shaft coupling, then separate the coupling from the lower end of the steering column.
        2. If equipped with a column mounted shifter, disconnect the transmission control linkage from the column shift tube levers.
        3. If equipped with a floor shifter, disconnect the backdrive linkage.
        4. Disengage all of the electrical connectors from the steering column assembly.
        5. Remove the floor pan cover-to-floor screws, the floor seal, and the cover.
        6. Remove the steering column bracket-to-instrument panel nuts and carefully lower the column. If equipped with an automatic transmission, disconnect the shift position indictor pointer.
        Once the steering column has been removed from the vehicle, be careful not to drop it (especially on it's end), lean on it or damage it in any way; the column is very susceptible to damage.
        1. Remove the column from the vehicle.
        To install:
        1. Position the steering column in the vehicle. If equipped with an automatic transmission, connect the shift position indicator pointer.
        2. Raise the column into position, then install the column bracket-to-instrument panel nuts and tighten to 25 ft. lbs. (34 Nm).
        3. Install the floor pan seal and cover, then secure using the retaining screws.
        4. Engage all of the electrical connectors to the steering column assembly.
        5. If equipped with a floor shifter, connect the backdrive linkage.
        6. If equipped with a column mounted shifter, connect the transmission control linkage to the column shift tube levers.
        7. Connect the intermediate shaft coupling to the lower end of the steering column, then secure using the nut/bolt.
        8. If removed for access or service, align the matchmarks and install the steering wheel.
        9. Connect the negative battery cable.

        Good luck..

        Nov 23, 2008 | 1986 Chevrolet El Camino

        Not finding what you are looking for?
        Cars & Trucks Logo

        Related Topics:

        17 people viewed this question

        Ask a Question

        Usually answered in minutes!

        Top Mazda Experts

        yadayada
        yadayada

        Level 3 Expert

        76164 Answers

        Colin Stickland
        Colin Stickland

        Level 3 Expert

        22156 Answers

        Jeff Turcotte
        Jeff Turcotte

        Level 3 Expert

        8273 Answers

        Are you a Mazda Expert? Answer questions, earn points and help others

        Answer questions

        Manuals & User Guides

        Loading...