Question about 2001 Dodge Caravan

1 Answer

ABS light is on . Locate ABS switch for change out

Posted by on

  • yadayada
    yadayada May 11, 2010

    what ABS switch?? there is no switch. what do u think ABS means??

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 84 Answers

If you know with sensor is bad, they are down at the wheel. If you take off the tire and look at the hub you will see it. It is held in with 1 bolt. Take out the bolt and wiggle it out and replace with the new one.

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need to locate the EBCM on a 1996 tahoe


Your brake light switch circuit also goes through the BLINKER SWITCH. Did you check that? (Most common culprit in GM vehicles.)

May 13, 2015 | 1996 Chevrolet Tahoe

2 Answers

HOW TO RESET ABS LIGHT ON 06 TACOMA


Locate the 16 pin Data Link Connector under the steering side.
To clear fault codes, switch off ignition, connect jumper wire between terminals TS (pin 12) and CG (pin 4). Switch the key on, then pump the brake pedal eight or more times in three seconds or less. When codes are erased, the ABS light should flash two times per second.
44e0be84-bb7c-4f67-9951-0595c3649f99.jpg
Switch off the ignition. Remove the jumper wire.
Hope that works.
If problem persists, contact a service personnel.

Jul 24, 2014 | 2006 Toyota Tacoma

1 Answer

I have a mitibushi lancer 1999 model.An the hand brake light wont go off ever.How can i fix this?


Are you sure it is due to the hand brake? the light will also come on for low brake fluid or due to low pressure in brake ssystem and also is the abs light on, if you have abs, a fast way to check this would be to locate the switch at the hand brake and remove the connector at the switch and if the light is still on then it is not due to hand brake.let me know, make sure the brake fluid is full and the sender in the master is good/

May 05, 2013 | Cars & Trucks

1 Answer

95 Regal Custom, ABS code #95 brake switch circuit and no brake lights. Replaced SLS still no change.


Check the brake light switch (location pedal) unplug the switch & bridge the wires & if the brake lights come on the switch is faulty. all you are doing by bridgeing the wires is bypassing the switch. What is SLS?

Oct 10, 2012 | Buick Regal Cars & Trucks

1 Answer

Abs light on 2004 gmc canyon


ABS light is on mean ur car have a AIR Bag mechanism have problems.Car might have a dying or a dead fuse problem in the main fuses box under the car hood.Change the fuse that link to the ABS mechanism should solved this problem,if not than ur car have a grounding problems,than it have a short somewhere.Must have the garage mechanic to trouble shoot and to locate the short.

Oct 28, 2011 | 2004 GMC Canyon

1 Answer

Break light is on as well as abs. Repair shop says they do not have access to the code to repair. Breaks work fine per two different shops. Is it just a switch that needs repair.


one of the sensors on the ABS system could be shorted, have the OBD codes read,, then cleared, that will help you see or limit what to check, once the codes have been cleared,, the lights should go off, if they come back on, then you need to locate the problem with the abs

Sep 06, 2011 | Ford Expedition Cars & Trucks

1 Answer

ABS light on fronm start up. Had problems witht he


just a guess on this but but have you tried resetting the computer for the switch?

Jun 27, 2009 | Jaguar XJ8 Cars & Trucks

1 Answer

ABS light, gear won't change


Sounds like he may have blown the brake light fuse while messing with the bulb. Make sure the correct bulb is installed. It should be a double filament bulb not a single.The wrong bulb will blow the fuse.
The shift lock solenoid uses the brake light switch to unlock.
The ABS code will be for the brake light system and will clear itself when the power is restored to the brake light switch.

Apr 05, 2009 | 2008 Toyota Sienna

1 Answer

ABS light won't turn off.


It could be that changing the switch told the ABS there was a fault. Try removing the fuse for the ABS and waiting 5 minutes for it to reset. ---I had a small ABS issue with my Volvo and the ABS fuse had blown. Good luck-- and if this helped can you give a rating?

Mar 27, 2009 | 1999 Ford Ranger SuperCab

Not finding what you are looking for?
2001 Dodge Caravan Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...