Question about 1987 Toyota Pickup

1 Answer

Engine dose not turn over-no spark from coil. replaced cap,rotor, plugs & coil

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

If it's not turning over, it sounds like a battery or starter issue. are you sure it's not cranking? since you're referencing the spark issue, i assume maybe you mean it's cranking, just not firing.

Posted on Feb 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is there no spark from spark plug 1995 k1500 silveraldo


1995 silverado has a distributor, remove the the distributor cap, make sure the distributor spins with the engine. also make sure the ignition rotor is not burned out or have a hole were it makes contact with the cap. also make sure the cap has a good carbon inside to make contact with the rotor, at this time get a screw driver, put it on the end of the wire from the coil to the cap, don't touch the metal part of the screwdriver, it will shock you if good, so put it at 5/16 from any metal on the engine, bracket, alternator , thermostat housing no matter, some one turns the engine over, check to see if the coil produces a spark, if the rotor turns, if ok it should have spark on all the wires, if it has no spark, remove the wire from the ignition coil and check if you have spak at the coil, if you have no spark, try getting a wire lead, connect it from the battery ground on one end, a screw driver on the coil to check for spark, and the other end of the wire with the key on, touch the - negative plug on the coil, that should produce a spark, if not spark yet, make sure you do have power at the coil with key on, if you do and it doesn't produce spark, replace coil. if it does spark but it is weak or yellow in color, replace coil. if coil is fine, replace distributor module,

Jul 10, 2014 | 1995 Chevrolet K1500

3 Answers

No spark


First does the rotor turn when cranking engine?? possible timing chain is out or stripped gear..are you sure it has no spark??did you verify this with a high output spark tester ? did you spray starting fluid in the tbi unit ?

Mar 23, 2012 | 2000 Chevrolet Astro

2 Answers

I have a 1998 durango, I have no spark from disturbtor but have spark from coil


Replace the distributor cap and rotor. If you have fire from the coil but not from the distributor cap, you have a bad contact point between the cap and rotor. Replace both and you should be good to go,, if the information that you have supplied is correct.

Aug 21, 2011 | 1998 Dodge Durango

1 Answer

On a 1992 chevy 1500- 350 engine, I can not get this thing to get a spark- i have replaced the plugs and wire, distributor cap and rotor, but you still don't even get a spark, it's getting fuel... Please...


Hi, Hope I can help you.
I do not know how you have checked for spark, but lets start from the beginning.
Lets start with an ignition systems check.
1. I want you to remove the high voltage coil wire. ( That's the wire in the center of the distributor cap.) Using a good pair of insulated pliers. I want you to hold it about 1/4 inch from a good engine ground. Now you will need a bit of help from a partner. Get them to turn the key and crank the engine. You should see a bright blue and well defined spark. Ok, If you have spark I want you to slowly move the coil wire away from the engine ground. As you do this I want you to pay attention to the coil tower. (The coil tower is where the other end of the coil wire is attached.) What your looking for is arcing and sparking at the coil tower. If this happens then you need to replace the coil with a new one. If this does not happen then your coil is working fine, and we will have to move on.
Note if you do not get spark from the coil wire replace the coil.

2. Ok if you have spark now we have find out if the spark is making it to the spark plugs. How are we going to do this? By checking the rotor, distributor cap, spark plug wires and spark plugs.First lets remove the distributor cap. This will allow use to inspected the rotor and the distributor cap. What your looking for is, cracks, carbon tracks and wear at the tip of the rotor. On the distributor ,look inside the cap for cracks, carbon tracks and wear on the terminals. If you find any of this replace the distributor cap and rotor. ( Note if you have any doubt of the condition of the rotor or the cap replace them.) Next lets check your spark plug wires. Lets pull off one of the spark plug wires from the spark plug side. Now inspect the wire connection for a white crusty powder. If you find crust replace your wires. Now you should check all of them the same way, but if even one has corrosion replace them all. You are going to have to inspect the wire its self . Going down the whole length of the wire. Holes cracks burn Marks and other damage. Once again if you find any damage replace them all.
I hope this will help you and good luck to all the read this FixYa
leave feedback thank you

Feb 21, 2011 | 1992 Chevrolet C1500

1 Answer

Can't get a spark


Hi, Hope I can help you.
I do not know how you have checked for spark, but lets start from the beginning.
Lets start with an ignition systems check.
1. I want you to remove the the high voltage coil wire. ( That's the wire in the center of the distributor cap.) Useing a good pair of insulated pliers. I want you to hold it about 1/4 inch from a good engine ground. Now you will need a bit of help from a partner. Get them to turn the key and crank the engine. You should see a bright blue and well defined spark. Ok,If you have spark I want you to slowly move the coil wire away from the engine ground. As you do this I want you to pay attention to the coil tower. (The coil tower is where the other end of the coil wire is attached.) What your looking for is arcing and sparking at the coil tower. If this happens then you need to replace the coil with a new one. If this does not happen then your coil is working fine, and we will have to move on.
Note if you do not get spark from the coil wire replace the coil.

2. Ok if you have spark now we have find out if the spark is making it to the spark plugs. How are we going to do this? By checking ower rotor, distributor cap, spark plug wires and spark plugs.First lets remove the distributor cap. This will alow use to inspected the rotor and the distributor cap. What your looking for is, cracks, carbon tracks and wear at the tip of the rotor.On the distributor ,look inside the cap for cracks, carbon tracks and wear on the terminals.If you find any of this replace the distributor cap and rotor. ( Note if you have any doubt of the condition of the rotor or the cap replace them.) Next lets check your spark plug wires. Lets pull off one of the spark plug wires from the spark plug side. Now inspect the wire connection for a white crusty powder. If you find crust replace your wires. Now you should check all of them the same way, but if even one has corrosion replace them all.You are going to have to inspect the wire its self . Going down the whole length of the wire. Holes cracks burn Marks and other damage.Once again if you find any damage replace them all.
I hope this will help you and good luck to all the read this FixYa

Feb 04, 2011 | 1991 Dodge Dakota

1 Answer

I have a 96 dodge avenger es, but there is no spark going to the engine's sparkplugs?


Hi, Hope I can help you.
I do not know how you have checked for spark, but lets start from the beginning.
Lets start with an ignition systems check.
1. I want you to remove the high voltage coil wire. ( That's the wire in the center of the distributor cap.) Using a good pair of insulated pliers. I want you to hold it about 1/4 inch from a good engine ground. Now you will need a bit of help from a partner. Get them to turn the key and crank the engine. You should see a bright blue and well defined spark. Ok, If you have spark I want you to slowly move the coil wire away from the engine ground. As you do this I want you to pay attention to the coil tower. (The coil tower is where the other end of the coil wire is attached.) What your looking for is arcing and sparking at the coil tower. If this happens then you need to replace the coil with a new one. If this does not happen then your coil is working fine, and we will have to move on.
Note if you do not get spark from the coil wire replace the coil.

2. Ok if you have spark now we have find out if the spark is making it to the spark plugs. How are we going to do this? By checking the rotor, distributor cap, spark plug wires and spark plugs.First lets remove the distributor cap. This will allow use to inspected the rotor and the distributor cap. What your looking for is, cracks, carbon tracks and wear at the tip of the rotor. On the distributor ,look inside the cap for cracks, carbon tracks and wear on the terminals. If you find any of this replace the distributor cap and rotor. ( Note if you have any doubt of the condition of the rotor or the cap replace them.) Next lets check your spark plug wires. Lets pull off one of the spark plug wires from the spark plug side. Now inspect the wire connection for a white crusty powder. If you find crust replace your wires. Now you should check all of them the same way, but if even one has corrosion replace them all. You are going to have to inspect the wire its self . Going down the whole length of the wire. Holes cracks burn Marks and other damage. Once again if you find any damage replace them all.
I hope this will help you and good luck to all the read this FixYa

Dec 04, 2010 | 1996 Dodge Avenger

2 Answers

My 99' dodge 1500 5.2 , turns over fine but no spark to start ?????


Hi, Hope I can help you.
I do not know how you have checked for spark, but lets start from the beginning.
Lets start with an ignition systems check.
1. I want you to remove the high voltage coil wire. ( That's the wire in the center of the distributor cap.) Using a good pair of insulated pliers. I want you to hold it about 1/4 inch from a good engine ground. Now you will need a bit of help from a partner. Get them to turn the key and crank the engine. You should see a bright blue and well defined spark. Ok, If you have spark I want you to slowly move the coil wire away from the engine ground. As you do this I want you to pay attention to the coil tower. (The coil tower is where the other end of the coil wire is attached.) What your looking for is arcing and sparking at the coil tower. If this happens then you need to replace the coil with a new one. If this does not happen then your coil is working fine, and we will have to move on.
Note if you do not get spark from the coil wire replace the coil.

2. Ok if you have spark now we have find out if the spark is making it to the spark plugs. How are we going to do this? By checking the rotor, distributor cap, spark plug wires and spark plugs.First lets remove the distributor cap. This will allow use to inspected the rotor and the distributor cap. What your looking for is, cracks, carbon tracks and wear at the tip of the rotor. On the distributor ,look inside the cap for cracks, carbon tracks and wear on the terminals. If you find any of this replace the distributor cap and rotor. ( Note if you have any doubt of the condition of the rotor or the cap replace them.) Next lets check your spark plug wires. Lets pull off one of the spark plug wires from the spark plug side. Now inspect the wire connection for a white crusty powder. If you find crust replace your wires. Now you should check all of them the same way, but if even one has corrosion replace them all. You are going to have to inspect the wire its self . Going down the whole length of the wire. Holes cracks burn Marks and other damage. Once again if you find any damage replace them all.
I hope this will help you and good luck to all the read this FixYa

Aug 15, 2010 | 1994 Dodge Ram

5 Answers

1995 dodge dakota 2wd 3.9 no spark to plugs,or coil,orfuelpump


First of all let's explain how the spark gets to the plugs. There is a crankshaft position sensor and a cam sensor. They are what determines when to fire the coils and injectors. The crank sensor is located on the passenger side on top of the bellhousing, the cam sensor is the pickup plate in the distributor. As the engin turns the send refernece pulses to the computer which grounds and ungrounds the ignition coil causing it to discharge and send voltager from the secondary coil wire to the center tower in the distributor cap. The rotor button recieves the voltage and distributes it to the 6 towers (1 for each cylinder) If you say you're getting spark from the rotor that tells me the primary side of the ignition system is working, and the secondary side is working into the distributor cap. I'd check for spark out of the plug wires at the plugs. Pull a wire and insert a #2 phillips screwdriver into it, hol the shaft of the screwdriver aprox 1/8"(no more) from the exaust manifold and observe the spark as someone turns over the engine. You should see a nice blue spark. If theres spark, spray a little gum cutter in the throttle body an crank it, if it fires you have a fuel problem. Install a fuel pressure gauge on the schrader valve on the fuel rail and observe it as you crank it. If theres no fuel pressure maks sure there's fuel in the tank, if so climb underneath and beat on the bottom of the tank with a rubber hammer, the pump may be going bad, sometimes you can jar them and make them run.

Aug 24, 2009 | 1995 Dodge Dakota

1 Answer

Im not getting spark to my spark plugs


Remove the distributor cap, so that the rotor is visible. Have an assistant turn the ignition to crank the engine over. If the rotor does not turn when the engine is cranking, then you need a timing belt or chain.

If the rotor does turn, then replace the coil.

Jun 15, 2009 | 1998 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...