Question about 2001 Volkswagen Jetta TDI

1 Answer

The drivers window switch assembly doesn't operate the windows, but it does unlock and lock the passenger doors minus the driver door...using the switches on the passenger doors, the windows will only go up or down in 2 inch increments...When unlocking the car with the remote, the passenger doors will unlock, and i will have to unlock the drivers door with the key...I need to be able to open the drivers window to pass nj inspection...The fuses are good and i replaced the drivers window motor...

Posted by on

  • 1 more comment 
  • Anonymous Mar 11, 2014

    where is the signal flasher located

  • Anonymous Mar 11, 2014

    i am trying to install MFC-J6510DW Brother Printer. I put in the CD, and it said Install MFL-Pro Suite. Is that what I should be installing???
    Then it said, The following applications should be closed before continuing the application: Acresso Software Management Agent, Acresso Software Management,PDFProFiltSrvPP. What in the world is this all about?? :)I can't close what I do not know. I think that you have to be a tech brain to figure it all out. Or... do I have the wrong disc in? The other disc said Documentation, so I didn't figure that I needed to install that. I still have not been able to connect the printer after 2 days.

  • Anonymous Mar 12, 2014

    the temperature display is not working properly on the rear view mirror. The direction compass is working

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 75 Answers

If you say you have replaced the driver's window motor and the window still won't go down, have you tried manually jumping the wires to the window motor? Try this with a positive wire and a negative wire from the battery to the terminals to the window motor. If the window motor works, the window switch assembly is possibly bad. Also, with a test light check and make sure you are getting power out of the driver's window switch assembly. Disconnect the wires going to the driver's window motor, connect the test light to a known ground(make sure the test light works) actuate the switch while touching the test light to the connector that came off the motor. Check both positions up and down. If no power check and make sure you have power going to the master switch. If no power, check the power window relays under the dash. You have to remove the cover under the steering wheel. It is held in place with some torx screws.

Posted on Feb 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

1 Answer

2001 Pontiac Bonneville Power locks and power windows dont work


Your power windows an door locks are controlled by a door module .
The vehicle is equipped with power windows controlled by the door modules. Each passenger door power window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally on its associated door. The driver door power window can only be operated from the driver door window switch built into the driver door switch assembly (DDSA).
When the driver door module (DDM) receives a window switch request from the DDSA, the DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation to occur. If the status information is correct, the DDM, either supplies power and ground to its associated window motor, or, if the request is for one of the passenger windows, sends a command via the power door serial data circuit to the passenger door module (PDM, LRDM, or RRDM) controlling the window. The passenger door module (PDM, LRDM, or RRDM) controlling the window then supplies power and ground to its associated window motor to move the window as requested.
When one of the local window switches mounted on one of the passenger doors is operated, the associated door module examines the request and checks to see if there are any messages from the DDM prohibiting the movement. If conditions are correct, and no prohibitive messages have been received from the DDM, the associated door module then supplies power and ground to its associated window motor to move the window as requested.
Your best bet would be to take your vehicle to a qualified repair shop !

Aug 06, 2016 | Pontiac Cars & Trucks

1 Answer

Where is the power window relay located in 2004 bonneville pontiac? thanks


Are all the windows inoperative ? The power window system on this vehicle is very complex in nature . Door modules , serial data communication networks ,messaging commands between modules etc... Factory description
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.
I have heard of water on rear floor shorting the data bus bring down the system . no power window operation . There are bus wires under the carpet an a scotch lock connector that corrodes causing this problem . This may or may not be your problem but you can stop looking for relays because their are none involved in the control of the power windows on your vehicle .
I

Jun 23, 2016 | Cars & Trucks

2 Answers

Where is the power window relay located in a 2002 mercury villager?


Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Visual Inspection Chart Mechanical Electrical
  • Improperly aligned window
  • Damaged window mounting
  • Window frame interference
  • Central junction box (CJB) Fuses:
    • F30 (10A)
    • F32 (20A)
    • F34 (20A)
    • F59 (7.5A)
  • Battery junction box (BJB) Fuses:
    • F20 (30A)
    • F27 (45A)
  • Switches
  • Circuits
  • Connectors
  • Heated back light
  • Relays
Which window is not working ?
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .

Apr 07, 2015 | 2002 Mercury Villager

1 Answer

How dow I reprogram power windows and locks after battery change?


There is no reprogramming for the door modules and sorry you dislike the dealer so much ! I work at a GM dealer ,have for over twenty years . No one knows your GM vehicle better . Your messing with something you have no clue about . The dealer is exactly the place you should be taking it to . Do you know the doors all have computers inside ? door modules , and can set DTC'S .Do you know what they are ? diagnostic trouble codes ! Do you know what serial data communications are ?
DTC B1562, B1567, B1572, or B1577
DTC B1582, B1583, B1592, B1593, B1612, B1613, B1622, or B1623
DTC B3142, B3147, B3152, or B3157
DTC B3172, B3177, B3182, B3187, B3192, B3197, B3282, B3287, or B3292
DTC B3377, B3382, B3387, B3392, B3397, B3452, B3457, B3462, B3467, B3472, B3477, B3482, B3517, or B3522
DTC B3527
DTC U1161-U1163 or U1170
The power door lock system consists of the following components:
• Driver door lock switch
• Passenger door lock switch
• Driver door switch assembly (DDSA)
• Driver door module (DDM)
• Passenger door module (PDM)
• Left rear door module (LRDM)
• Right rear door module (RRDM)
• Driver door lock actuator
• Passenger door lock actuator
• Left rear door lock actuator
• Right rear door lock actuator
• Driver door cylinder unlock switch
• Class 2 serial data circuit
• Power door serial data circuit
• DRVMDL Fuse (10 amp)
Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation
• PASS MDL Fuse (10 amp)
Front Passenger Door Module logic and internal driver operation
• RRDR MDL Fuse (10 amp)
Left Rear Door Module and Right Rear Door Module logic and internal driver operation

Aug 17, 2017 | 2003 Pontiac Bonneville

1 Answer

I have an 02 pontiac boneeville My power windows and my poer locks will not work the lights inside my car will not turn on and my radio will not shut off when my car is turned off and the key removed. it...


Do you know what electronic control modules are ?
Power Windows System Components
The following components are used to control the power windows:
• Driver Door Module (DDM)
• Passenger Front Door Module (PDM)
• LH Rear Door Module (LRDM)
• RH Rear Door Module (RRDM)
• Driver Door Switch Assembly (DDSA)
• RH Front Power Window Switch
• LH Rear Power Window Switch
• RH Rear Power Window Switch
• LH Front Power Window Motor
• RH Front Power Window Motor
• LH Rear Power Window Motor
• RH Rear Power Window Motor
• PWR WDO 30 Amp Circuit Breaker
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door power window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally on its associated door. The driver door power window can only be operated from the driver door window switch built into the driver door switch assembly (DDSA).
When the driver door module (DDM) receives a window switch request from the DDSA, the DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation to occur. If the status information is correct, the DDM, either supplies power and ground to its associated window motor, or, if the request is for one of the passenger windows, sends a command via the power door serial data circuit to the passenger door module (PDM, LRDM, or RRDM) controlling the window. The passenger door module (PDM, LRDM, or RRDM) controlling the window then supplies power and ground to its associated window motor to move the window as requested.
When one of the local window switches mounted on one of the passenger doors is operated, the associated door module examines the request and checks to see if there are any messages from the DDM prohibiting the movement. If conditions are correct, and no prohibitive messages have been received from the DDM, the associated door module then supplies power and ground to its associated window motor to move the window as requested.

Your best bet , take it to a qualified repair shop that has the diagnostic tools to diagnose this . Do you know what DTC'S - diagnostic trouble codes are ? DTC B3377, B3382, B3387, B3392, B3397, B3452, B3457, B3462, B3467, B3472, B3477, B3482, B3517, or B3522.
Hooking up a factory scan tool checking codes and seeing if the door modules communicate .

Sep 03, 2017 | 2002 Pontiac Bonneville

1 Answer

2001 aurora power window/lock failure.


Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door power window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally on its associated door. The driver door power window can only be operated from the switch built into the DDSA.
If the driver door module (DDM) receives a window switch request from any of the window switches built into the DDSA, the DDM checks the Class 2 serial data to see if conditions are correct (i.e. ignition switch position) to permit window operation to occur. If conditions are correct, the DDM, either supplies power and ground to its associated window motor, or sends a command via the power door serial data line to the passenger door module controlling the window. The passenger door module controlling the window then supplies power and ground to its associated window motor to move the window as requested.
When one of the local window switches mounted on one of the passenger doors is operated, the associated passenger door module examines the request and checks to see if there are any messages from the DDM prohibiting the window operation. If conditions are correct, and no prohibitive messages have been received from the DDM, the associated passenger door module then supplies power and ground to its associated window motor to move the window as requested.


Class 2 data network wires under the carpet behind driver seat. Water shorts out the network an and it won't work .
your looking for tan/white wire's and a connector . This is where the problem is .

Aug 13, 2017 | 2001 Oldsmobile Aurora

1 Answer

Volvo V70 Driver Door switches do not work


the main ground for the switch assembly is open somewhere.

Sep 04, 2009 | 2002 Volvo V70

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

Not finding what you are looking for?
2001 Volkswagen Jetta TDI Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...