Question about 1995 Chevrolet Lumina

1 Answer

The starter connection bolt from battery to starter has strip how do i replace it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 617 Answers

Take a pair of vise grips to turn stripped bolt, is bolt stripped or threads where bolt just turns

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to put in a starter on a 1993 mercury marguis


get a lift
buy a new or rebuilt starter
drive the car onto the lift
disconnect the negative battery cable
put the car up in the air
disconnect the wiring from the starter, use your cell phone camera to take a picture before removing the wires
take the top and bottom bolts out which hold the starter to the bell housing
pull starter out and down
put new starter in and put bolts back in
look at cell phone picture and reconnect wiring the same way
let car down and reconnect battery
you are done

Jun 25, 2011 | 1993 Mercury Grand Marquis

2 Answers

2003 Kia RIO WHEN TURNED TO ON CAR starts and the starter will not stop turning


Replace the starter.



Removal & Installation

1.5L & 1.6L (VIN 5) Engines

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the 4 upper intake manifold stay bracket bolts.
  4. Disconnect the starter electrical connections.
  5. Remove the upper starter bolts.
  6. Remove the lower starter mounting bolt(s) and the starter.

    0996b43f80207fb6.jpg

    Fig. Starter mounting-1.5L and 1.6L engines


To install:
  1. Install the starter.
  2. Install the lower starter bolt and tighten to 27-38 ft. lbs. (37-52 Nm).
  3. Connect the starter electrical connections.
  4. Install the intake manifold support bracket and finger-tighten the 3 mounting bolts. Tighten the lower bolt to 27-38 ft. lbs. (37-52 Nm).
  5. Install the 4 upper intake manifold stay bracket bolts and tighten to 27-38 ft. lbs. (37-52 Nm).
  6. Install the upper starter bolts and tighten to 27-38 ft. lbs. (37-52 Nm).
  7. Connect the negative battery cable.

1.6L (VIN 3) Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Air intake assembly Shift cable and bracket Starter electrical connections Starter

To install:
  1. Install or connect the following:

    Starter Starter electrical connections Shift cable Air intake assembly Negative battery cable

May 04, 2011 | Kia Rio Cars & Trucks

1 Answer

When replacing the alternator on a 2003 VW Passat V6,how do you get the the alternator off of the car. There seems to be no room to get it out


NOTE On A1 and A2 platform vehicles equipped with 010 automatic transaxle, access to the starter motor is limited. Although not necessary, it is recommended that the intake and exhaust manifolds be removed to access the starter.
  1. For safety purposes, disconnect the battery ground cable.
  2. Raise and safely support the front of the vehicle with jackstands.
  3. For A3 vehicles, use a floor jack (with a block of wood on the chock) to support the engine by the oil pan. Do NOT jack the car by the oil pan under any circumstances! The floor jack is ONLY to support the engine while the starter is being removed. The bolts that secure the starter to the transaxle are also used to secure the front engine mount to the transaxle.
  4. If necessary, label the small wires before disconnecting them.
  5. Disconnect the large cable, which is the positive battery cable, from the solenoid.
  6. On 010 transaxle-equipped vehicles, remove the bracket that secures the starter to the engine.
  7. Remove the starter mounting bolts, while supporting the weight of the starter.
  8. Pull the starter straight out from the transaxle.
NOTE On vehicles with a manual transaxle, there is a bushing where the starter shaft fits into the bell housing. If the shaft or bushing are worn or if the starter has been jamming, the bushing should be replaced. There is a special bushing removal tool available but a small inside bearing removal tool is usually sufficient.
  1. Install the starter into the transaxle.
  2. Tighten the starter mounting bolts as follows:
    1. All vehicles except 010 transaxle:
      M8 nut: 89 inch lbs. (10 Nm) M10 nut and bolt: 44 ft. lbs. (60 Nm) M12 bolt: 33 ft. lbs. (45 Nm)
    2. 010 transaxle only:
      Mounting flange bolt: 15 ft. lbs. (20 Nm) Mounting bracket bolt: 18 ft. lbs. (25 Nm)
  3. Attach the electrical connections to the starter.
  4. NOTE: Be careful not to over tighten the battery cable connection. The metal is soft and the threads will strip easily.
  1. Lower the vehicle from the jackstands. Connect the negative battery cable.

Jan 08, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

How do i install a new starter in a 96 jetta GL


Instructions Things You'll Need:
  • Torque wrench, Floor jack, Safety stands, Common Hand tools
    Remove the Malfunctioning Starter
  1. Park your VW Jetta on a level surface, activate the emergency brake and place blocks behind the back tires for safety. Disconnect the negative battery cable with a terminal puller. Raise the front end of the car with a jack for easier access to the starter.

  2. Remove the intake and exhaust manifolds for easier access to the starter on Jettas with a 010 automatic transaxle, such as the A1 and A2 platform models.

  3. Place a floor jack under the engine, with a block of wood on the chock, for extra support on models such as the A3 platform. Only use this jack for added support, not to raise the vehicle.

  4. Label the starter electrical connections with masking tape and permanent marker to help you remember where the wires connect to the starter later. Disconnect the starter electrical connections, including the positive battery cable.

  5. Detach the bracket that helps to secure the starter to the engine, if necessary.

  6. Check the bushing on a vehicle with a manual transaxle (located where the starter shaft fits into the bell housing). If the bushing shows wear or the starter was jamming, you need to also replace the bushing.

  7. Support the weight of the starter and remove the starter mounting bolts. Place all nuts and bolts in a safe location to prevent loss, such as a baby food jar. Pull the starter straight away from the transaxle and remove it from the vehicle.

  8. Take your malfunctioning starter to the parts store with you. Aftermarket distributors remanufacture most of the starters they sell, so you can likely obtain a partial credit toward your new starter by exchanging your old one. Be sure that you take care not to damage the starter in transit, because the better condition it is in, the more you can get for it.

  9. Purchase a replacement starter that has the same or higher cranking capacity (power rating) as the original starter. Also, match the bolt patterns, drive gears and electrical connections. Your owner's manual may list specifications or the auto parts technician will help you determine them. Purchase an owner's manual on Volkswagen of America (see Resources).

  10. Install the New Starter
  11. Place the starter in the correct position next to the transaxle. Secure the starter in place with the starter mounting bolts. Torque the bolts to 33 foot pounds (45 Nm) on M12 vehicles and 44 foot pounds (66 Nm) on M10 vehicles.

  12. Tighten the mounting bolts differently on Volkswagen Jettas with a 010 transaxle. Torque the mounting flange bolt to 15 foot pounds (20 Nm) and the mounting bracket bolt to 18 foot pounds (25 Nm).

  13. Connect the wires to the starter. The metal on the battery cable is soft and strips easily, so refrain from over tightening the retaining nut.

  14. Lower your Jetta back to the ground. Reconnect the negative battery cable. Turn the key in the ignition to see if your new starter motor functions correctly.

Oct 29, 2010 | 1996 Volkswagen Jetta

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

1 Answer

How to replace starter 5.4l


The starter is bolted to the bell housing.
Is has a positive cable from starter solenoid.

1. Remove the negative battery cable at the battery.
2. remove the power cable from the starter.
3. remove the starter mounting bolts (typically only 2 bolts)
4. Install new starter. Hand tighten mounting bolts
5. Secure both bolts to about 35 Lbs of torque
6. Connect power cable.
7. Connect the negative battery cable at the battery.
8. Test (start the car).

Oct 15, 2009 | 1999 Ford Expedition

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

4 Answers

Changed the starter in a 97 jetta and it wont turn over just keeps setting off the alarm, is the fuel pump locked and if it is how do you unlock it?


When you changed the starter, you would've had to disconnect the battery. Disconnecting the battery most likely reset your alarm system so now it is not disarming properly. You'll need to have your alarm reprogrammed most likely

Sep 15, 2009 | 1997 Volkswagen Jetta

1 Answer

Car wont start; jumped successfully once; wont start again; battery fine


1. Start solenoid stuck: remove minus battery cable. Remove starter. Remove solenoid and clean and lightly grease the slide.
2. Go to most Auto Parts Stores for a free test.
3. If the battery connections and Block Ground connections are not clean, make them clean.
4. Only clean the positive connection at the starter After removing the battery minus connection.
5. Use 150 grit sand paper to clean the small solenoid lead. If you must remove the small bolt be very sensitive of your applied pressure, these small bolts break and strip easily.
SAFETY: The last connection made is always the negative/minus battery connection for all starter related repairs. These wires will burn you if the battery is not safely disconnected and best when wrapped by a rag or paper towel.
Good Luck.

Jun 28, 2009 | 1994 Acura Vigor

3 Answers

How to replace the starter for a 95 buick lesabre


Be sure to disconnect the battery first. There are HOT wires connected to the starter. Disconnect three wires and two mounting bolts. It can be difficult to reach a wrench in there.

The new starter will come with shims, thin strips of metal. These are for getting the right distance between the starter gear and the flywheel. Hopefully you won't need them. But if the new starter is noisy when mounted, shim it some.

Jun 02, 2009 | 1995 Buick LeSabre

Not finding what you are looking for?
1995 Chevrolet Lumina Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...