Question about 1991 Honda Civic

1 Answer

When i press the brakes i have no tension. we replaced the master cylander and the problems still there what else could cause this

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

Brokin line, or caliper shot or wheel cylinder shot

Posted on Feb 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My right front brake is locking up could this be caused by the master cylander booster? Lines calipers hoses all ok


no if it were the booster it would be all brakes not just one . daugher had one locking up and it was the hose had gone bad internally but looked fine outside .

Oct 05, 2015 | 2000 Chevrolet Chevrolet Cavalier Base

1 Answer

Brakes


It sounds to me as though it is the master cylinder. You can try bleeding the master cylinder itself, just to see if you have pressure there. But if you cannot pump them up, I'm betting on a bad master cylinder. I hope this helps you.

Mar 25, 2014 | 1995 Ford Explorer

1 Answer

Brake master cylander


Not mentioned about what the fault was but if this is leaking or is jammed then the master repair KIT has to be replaced which includes the brake bucket . If the piston is jammed then the brake cylinder or piston must be changed.

Mar 14, 2012 | 1993 Chevrolet Beretta

2 Answers

My brake pedal goes to the floor, and the brakes don't grab at all. i havebled them & it seems to have gotten worse, any suggestions?


Make sure you have good fluid on the resevoir then bleed each wheel out really good.A steady stream should shoot out of the bleeder valve when the brake pedal is pressed. If you have no pressure,then your vacumn diaphram maybe bad or the master cylinder itself.Bleed it at the resevoir also to make sure you have not gotten any trash or water in the system.If you still have no pressure I would suspect the master cylinder.

Aug 17, 2011 | 1996 Nissan 200SX

1 Answer

I drive a Chevy Venture 2004. in the mornings, when I start up the engine, the brake pedal goes down when I push it. Sometimes, when I am driving slow and I push the brake, it goes down, more than normal....


first check brake fluid level
if fluid is low, this is a good indication that pads or shoes need replacing
check brake lings for wear
check that pcv valve from engine to brake booster is not clogged
to check this pull it out of valve cover and shake it
if it rattles it is good
if it dont rattle it is clogged,replace it
if pads and linings are good and no obvious signs of brake fluid leaking anywhere,(wheels cylanders etc>then the brake master cylander or brake booster is bad
more likely to be booster

Dec 16, 2010 | 2000 Chevrolet Venture

2 Answers

Problem with brakes


the brake booster has a rubber diaphragm in it that sometimes goes out and causes that problem

Apr 21, 2009 | Dodge Ram 3500 Cars & Trucks

2 Answers

Ford Escape 2001 model - brake pedal sticking


What pushes the pedal back when you release the pedal is a strong spring inside the master cylander that pushes on the piston that moves the brake fluid to the calipers and wheel cyls. This spring should last the life of the master cyl. and replaceing the master cyl. is the only way I know of to replace your weak spring or a piston that is hanging up. Check all the linkage under the dash to be sure that there is not a problem with your pedal linkage that is causing your problem

Jun 23, 2008 | 2001 Ford Escape

Not finding what you are looking for?
1991 Honda Civic Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...