Question about 1998 Isuzu Trooper

1 Answer

Cant take cv out of housing do i need to take the top and bottom ball joints off

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 85 Answers

Yes, sometimes just the bottom.

Posted on Feb 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rubber cv boot on 1999 Isuzu rodeo


how to , who can, what are all steps. are there special tools?
sure. if the boot is bad, so be the joint, Yah think?
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Halfshaft from the vehicle
    • Snapring and bearing
    • Snapring and oil seal
    • Mounting bracket
    • CV-joint boot
    • Circlip and inner joint housing
    • Snapring and spacer
    • Inner joint balls
    • Snapring and inner CV-joint
    • To install:
    • Install or connect the following:
      • Inner CV-joint and snapring
      • Inner joint balls
      • Spacer and snapring
      • Inner joint housing and circlip. Add 150 grams CV-joint grease.
      • CV-joint boot
      • Mounting bracket
      • Oil seal and snapring
      • Bearing and snapring
    • Install the halfshaft and mounting bracket to the vehicle.
    • Check the wheel alignment and adjust as necessary.

Jun 30, 2014 | 1999 Isuzu Rodeo

1 Answer

Front driver side cv joint?


could be top/bottom ball joint easy to check ,jack up so wheel off ground hold wheel at 12 o'clock and 6o'clock (the position not the time) and wobble back and forwards then do the same but holding at 3 an 9 if notice movement further investigation needed,while you wobble wheel get someone too look at top/ bottom ball joints ,track rod end if they dont appear to be moving then more than likely bearing this is best done with vehicle on a lift but should be able to carry out on the ground the cv joint could also be responsible but would need a garage to determine as a bit more complex

Apr 02, 2014 | 2007 Ford F-150 Super

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

1 Answer

How do i remove driveshafts


We'll do one side of the car and you can repeat the steps on the other side, before you remove the wheels you have to remove the large centre nut that holds on the cv joint. the nut is in the centre between the wheel nuts, its normal a 34'' or 36'' you'll have to us a power bar as they can be tight. once the nut is removed, jack the car up and remove the wheel, next you have to remove the nut holding the (bottom) ball joint, when the nut is off the ball joint will be hard to seperate hit the ball joint on all sides with a hammer if it still wont move you will have you use a ball joint seperater (fork shape) to brake the connection. once the ball joint is removed you can (tap) the the cv joint out of its housing in the centre of the wheel( where the big nut was ) be careful not to damage the treads. with the cv joint free the driveshaft will hand free some off them just pull out when you remove the clips on the rubber booth attached to the driveshaft and gearbox, others booths are bolted in with small 13mm bolts, repeat the process on the other side. good look I hope this helps (Rate me answer please)

Aug 30, 2010 | 2000 Volkswagen Golf

2 Answers

Left turns sometimes makes knockin noise seems left front, i see that the outside of that tire is worn too. I had front brakes/rotors replaced and seems since then it was happenin but not always


Could also be the upper ball joint, put a jack under the lower control arm and jack the left wheel off the ground, the trick is to try to get it at normal ride hight, grab the tire at the top and bottom and try to push and pull the top in and out inline with the ball joint. have a helper eye the ball joint and see if there is any motion(play) at the joint. If not, check the bottom the same way. if they are both good, try it side to side to check the tie rods for play, make sure the steering wheel is locked. if all checks good than it is probably the cv joint if the truck is four wheel drive, if it is not four wheel drive it's definately is not a cv joint because you don't have them. For the four wheel drive model, go to a large parking lot, put the truck in a tight left turn, this will stress the cv joint, making it click, you will hear the noise from the side with the bad joint. Then tru a hard right turn, then do the same things again, this time driving in reverse. That should allow you to isolate the noise, Please rate this four thumbs up if it helped, i appreciate your feedback. Thanks, Bob

Jan 20, 2010 | 1993 Dodge Dakota

1 Answer

Where can I find the rubber seals for the ball joints that houses the cv joints on the front axle for a nissan safari ldv '89 model


If you are refering to those corrugated rubber boots, it is highly recommended to replace those CV shafts as the dirt and moisture contamination is not a good thing in CV joints. Dirt and moisture are the leading causes of CV shaft failures. You can by the boots as a repair boot and those wrap around the CV shaft/joint area and bolt together. If you are talking about the little rubber boots on the ball jonts themselves at the end of a steering link, those boots are not sold individually. They only come with new Ball joint assemblies.

Aug 04, 2009 | 1987 Nissan Pickup

1 Answer

02yukon i cannot get the cv joint out from the wheel/brake assem


Remove steering joint.Then bottom ball joint then you should be ok.

Jul 13, 2009 | 2001 GMC Yukon

1 Answer

99 jeep gc need to replace cv joint


Not to bad you will need a ball joint spreader. some sockets wrench's.prybar.Remove the tire then loosen cv bolt. Remove brake caliber and bracket.re move ball joint nut.Remove steering rod nut.Get the ball joint spreader an remove steering rod then remove the ball-joint.Take the cv bolt off grab the strut and pull outward .With a rubber mallet knock cv out of housing.The remove from transmission.you my have pry a little.

Jan 16, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Cant get the cv joint to come out of the front housing


sometimes they are very hard to get out . it will need a large prey bar not a large screwdriver . it will take a little force between axle & trans mabe hammer to smack axle free. you will have to remove the outer caliper, rotor, spindle and bottom ball joint suspension befor e step one

Dec 24, 2008 | 1993 Isuzu Rodeo

1 Answer

CV joint replacement


Generally no tool is required. If you use a "pickle fork" you will risk damaging the dust boot.

Have you tried whacking the spindle right near where the ball joint stud comes through? This will take a few good shots to break it loose.

Be careful not to hit the threads!

Jun 25, 2008 | 2001 Honda Odyssey

Not finding what you are looking for?
1998 Isuzu Trooper Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...