Question about 2001 Toyota Camry

1 Answer

2001 toyota camry

How does the shaft remove from tranny..doesnt pop out like it should

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 51 Answers

Some are harder to remove than others, but should pop out of there. try a ladies foot pry bar/ get the curved edge behind the cv axle and pry it out , I found this works best. hope this helps and god bless.

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know the marker settings on my motor balance shafts


I use a manual. You really need to get one.Timing is a critical part of engines... Especially if it an interference engine.

Oct 07, 2016 | 2001 Toyota Camry

1 Answer

Airbag warning light doesnt come on 2001 toyota camry


bulb could be burned out.if you have any problems with airbags.let dealership check it out.could be bulb.

Dec 24, 2012 | 2001 Toyota Camry

1 Answer

Can I replace the trans-axle through an access on the outside of the transmission? Or is it necessary to remove the transmission in order to change the trans-axle on a 1998 Camry?


the trans axle is the tranny...but if you meen the c.v axles you can take off the axle nut ..then remove the tie rod and lower ball joint and change the axle shaft with out tranny removal.. the tranny is called a transaxle on a front wheel drive car cause the differential and the tranny is one unit where as on rear drive car you have the tranny and then a rear diff connected bt a drive shaft where there is 3 seprate units

Feb 21, 2011 | 1998 Toyota Camry

3 Answers

I need to remove my front axel on my 1989 toyota camry


Jack up car and apply e-brake. car will roll if one of the front tires leaves the ground. remove tire , spindal nut and lower ball joint bolts. remove axle from hub then use a prybar to pop it out of trans. the passenger side will have a braket holding axle to engine , remove bolts from braket or squeeze snap-ring to rmove axle from braket.

Jan 11, 2011 | 1989 Toyota Camry

1 Answer

I'm replacing the passenger side cv half shaft on my 89 Camry wagon, 4 cyl, fwd. We got the wheel assembly out of the way. Got the snap ring off that's about half way up the shaft around the bracket that...


Welcome to FIxYa.com



raise the car higher and use two pry bars in a V of each other when you use one the shaft will bind.





leedavidian_36.jpg


Thank you for using FixYa.com

Regards, Lee Davidian

Nov 21, 2010 | 1989 Toyota Camry

1 Answer

Removing oil pan on 2001 2.2 litre camry


You will actually have to remove the tranny to access the 3 bolts

Jun 18, 2009 | 1997 Toyota Camry

1 Answer

1991 toyota camry, starts fine but will not shift out of park, i can move the shifter into different positions but it doesnt change the gears, the transmision fluid stick/rod says the tranny fluid is hot,...


I would check to see if the shifting rod is connected to the tranny, you shouldn't be able to shift the car unless you had your foot on the break. IF the rod is connected then there is something inside the tranny that isn't right.

Sep 30, 2017 | 1991 Toyota Camry

1 Answer

Can not remove CVjoint on the drivers side of my toyota camry


no just put a good sized flathead screwdriver in between the end of the cv joint and where it goes into the transmission and pop it out

Mar 22, 2009 | 1990 Toyota Camry

1 Answer

1987 Toyota Celica ST half shaft


pull wheel, remove nut on half shaft, calaber, brakes, roader, tie rod, lower control arm, pop out half shaft from knuckle reinsert shaft to tranny and put back together easy looking about an half hour to an hour

Feb 23, 2009 | 1987 Toyota Celica

1 Answer

06 camry 2.4 engine removal


Its a front wheel drive just separate the transmission. Loosen all the bolts around the transmission bell housing and loosed the converter from the flywheel. The engine will come out and leave the tranny in the car. very easy. Good luck

Dec 12, 2008 | 2006 Toyota Camry

Not finding what you are looking for?
2001 Toyota Camry Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...