I have removed caliper and pads, how do i remove caliper mounting bracket to replace rotor?

Front brakes are very simple to do:

• Pull off the front tires.
• Remove the brake pads by removing the slide pin bolts where the piston assembly attaches to the caliper mounting bracket. The slide pin bolts are usually a 12 or 14mm bolt. Once the piston assembly is free slide the old brake pads out.
• Compress the piston back into the caliper by using a large pair of channel lock pliers or a c-clamp. If you don't do this, you won't be able to get the new pads on.
• Before you put the new pads on, replace the rotor.
• Remove the two bolts for the caliper mounting bracket. They are in the back and are bigger than the slide pin bolts. Usually a 17 or 19mm bolt.
• Pull off the caliper mounting bracket.
• At this point the old rotor should slide right off. If it doesn't slide right off, look for a screw in the center of the rotor, some cars will have a screw there to hold the rotor on. If there's no screw and it still won't come off, try tapping it with a hammer. If you're replacing the rotor, don't be shy.
• Put the new rotor on. Make sure to clean off any grease with brake cleaner that may be on the braking surface from packaging.
• Put the caliper mounting bracket back on.
• Put the new brake pads on. Make sure to use some anti-squeal grease on the back of the pads.
• Put the caliper assembly back on with the slide pins. Grease up the slide pins as well.
• Put the wheels back on.
• Make sure to pump your brakes 10 - 15 times before you drive off. Because you compressed the piston back into the caliper, the piston will not be contacting the brake pads unless you pump the brakes.

Good Luck!
~Brandon

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

Front brake
Step 1: Identify Front Disc Brake Components

Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads

Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper

Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads

Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount

Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor

Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper

Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor

Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads

Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper

Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Removal & Installation Front To Remove:

1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
2. Remove the tire and wheel assembly.
3. Install 2 wheel nuts to secure the rotor on the hub.
4. Remove the bottom brake caliper pin bolt.
5. Pivot the brake caliper body upward and secure out of the way. Do NOT disconnect the hydraulic brake flexible hose from the caliper.
6. Compress the piston back into the bore using a C-clamp. Figure of brake assembly with caliper raised showing brake pads in mounting bracket
   
   
7. Remove the inboard and outboard brake pads from the brake caliper bracket.

To Install:

1. Install the brake pad retainers and both brake pads into the caliper bracket.
2. Pivot the brake caliper down over the brake pads and into the brake caliper bracket. Insert the lower brake caliper pin bolt and torque bolt to 70 ft-lb. (95 Nm).
3. Reinstall the tire and wheel assembly.
4. Lower the vehicle.
5. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
6. Check the master cylinder level and add fluid as necessary.

Rear To Remove:
Rear disc pads R&I

1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
2. Remove the tire and wheel assembly.
3. Install 2 wheel nuts to secure the rotor on the hub.
4. Remove the upper caliper mounting bolt.
5. Pivot the caliper down to access the pads.
6. Remove the inboard and outboard pads from the caliper bracket.
7. Remove the brake pad clips from the caliper bracket.
8. Compress the piston back into the bore using a C-clamp and the old inner pad.

To Install:

1. Install new brake clips in the caliper bracket.
2. Install the inboard and outboard pads in the caliper bracket.
3. Pivot the caliper up over the pads.
4. Reinstall the upper mounting bolt and tighten to 32 ft. lbs. (44 Nm).
5. Remove the 2 wheel nuts securing the rotor.
6. Reinstall the tire and wheel assembly.
7. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
8. Check the master cylinder level and add fluid as necessary.

Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket

1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
2. Raise and support the vehicle safely.
3. Remove the wheel and tire assembly.
4. Compress the brake piston back into its bore using a C-clamp.
5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
6. Remove the inboard and outboard pad.
7. Remove and discard the anti-rattle clips.

To Install:
Caliper bracket sleeves

1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
2. Install new anti-rattle clips.
3. Position the inboard and outboard pads into the support bracket
4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
7. Install the tire and wheel assembly. Lower the vehicle.
8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.

Rear To Remove:

1. Remove 2/3 of the brake fluid from the master cylinder.
2. Raise and safely support the vehicle.
3. Remove the wheel and tire assembly.
4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
5. Remove the brake pads from the caliper mounting bracket.
6. Remove and discard the anti-rattle clips.

Rear brake caliper

To Install:

1. Install new anti-rattle clips.
2. Position the brake pads to the caliper mounting bracket.
3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
5. Install the wheel and tire assembly.
6. Lower the vehicle.
7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.

To replace the rotors, remove the calipers and then just take the rotors off. If you don't open the hydraulic system (you should not need to) no bleeding is necessary, but you will need to retract the caliper pistons using a "c" clamp in order to get them back over the new rotors. Make sure the slide pins that the bolts go through to hold the calipers on are free and that the piston boots are in good condition to avoid any further problems there.

The pads are mounted to the caliper. The caliper is bolted to the spindle bracket. There is brake hardware which should be replaced with the pads.
Look behind the wheel at the backside of the spindle bracket. The spindle bracket is on the verticle shaft with coils on one end and an A shaped bracket on the other. There are usually 2 bolts that may have normal bolt ends or "Allen" bit fittings.

When you buy the brake hardware you can check for the proper socket for the mounting bolt. You unbolt the caliper, use a rope or wire to suspend it under the frame without disconnecting the brake line.

The pads come off with the hardware. You need to compress the caliper pistons to make the new pads fit. Use a C clamp and an old pad to squeeze the pistons back into the caliper. Remove the Master Cylinder cover so fluid can return.

Then use a bonding chemical like "brake quiet" to mount the rear pad to the caliper piston. Mount outside pad to caliper and then slide caliper over the rotor on the spindle bracket. Lube the slides of the new brake hardware and bolt into place.

You should have the rotors checked for thickness and whether they are warpped before you put on the new pads.

Removal & Installation


After removing the caliper body, unfasten the retaining bolts and remove the caliper mounting bracket, in order to remove the rotor

1. Use a siphon or clean turkey baster to remove about half of the brake fluid from the master cylinder.
   
2. Raise and safely support the vehicle and remove the tire/wheel assembly.
   
3. Remove the caliper mounting bolts, then lift the caliper assembly away from the brake rotor.
   
4. Use a suitable piece of wire to suspend the caliper assembly. This will prevent the weight of the caliper from being supported by the brake flex hose which will damage the hose.
   
5. Once the caliper body and brake pads are removed, unfasten the caliper bracket mounting bolts, then remove the bracket from the rotor.
   
6. Remove the rotor retaining screws.
   
7. Remove the brake rotor by pulling it straight off the wheel mounting studs or if seized in place, remove the stubborn brake rotor by threading in two 8 x 1.25mm bolts, two turns at a time until the brake rotor is released.
   

To install:

1. If necessary, completely retract the piston into the caliper using a large C-clamp or other suitable tool as provided in the front disc brake pad replacement procedures in this section.
   
2. Install the brake rotor onto the wheel hub and tighten the mounting screws.
   
3. Install the caliper mounting bracket and secure with the retaining bolts.
   
4. Install the caliper and pad assembly over the brake rotor and mounting bracket and install the mounting bolts.
   
5. Fill the master cylinder to the proper level with fresh brake fluid.
   
6. Install the tire/wheel assembly and lower the vehicle.
   
7. Pump the brake pedal until the brake pads are seated and a firm pedal is achieved before attempting to move the vehicle.
   

CAUTION Do not move the vehicle until a firm pedal is obtained.

1. Road test the vehicle to check for proper brake operation.
   

take the wheels off the front,,remove the 2 bolts holding the brakes caliper to the caliper mount and pull off the caliper,then remove the old pads by popping them out, and the remove the 2 bolts holding the caliper mounting bracket to the hub and then remove the rotor,,,to either resurface it,,or replace it with a new one,,,the put the rotor back on(new one) install the mounting bracket and pads and press the caliper piston in with a pliers and then put it back onto the mounting bracket and then tighten all bolts,and do the other side,,pump up brakes and youre good to go

Disc Brake Pads Removal & Installation Front To Remove:

1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
2. Raise and support the vehicle safely.
3. Remove the wheel and tire assembly.
4. Compress the brake piston back into its bore using a C-clamp.
5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
6. Remove the inboard and outboard brake pads.
7. Remove and discard the anti-rattle clips.

To Install:

1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
2. Install new anti-rattle clips.
3. Position the inboard and outboard pads into the support bracket
4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.

1. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
2. Tighten the mounting bolts to: 74 ft lb. (110 Nm) 1500 series

• 80 ft lb. (110 Nm) 25/3500 series.

1. Install the tire and wheel assembly. Lower the vehicle.
2. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
3. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.