Question about 1995 Ford Bronco

1 Answer

Replaced wheel cylinders and calipers - could not

Replaced wheel cylinders and calipers - could not get good pedal when bleeding brakes - replaced master cyl -- still same problem-- pedal will come up some after pumping 5 to 10 times and will hold pressure until you release it - then its right back to the floor. 1995 bronco abs

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 532 Answers

Alot of air in the lines,probably the rears,fill up the master cylinder and loosen the bleeder screws on the rear and let them drip for 10-15 minutes,may not drip at all so thats air in it,tighten them up and pump the brakes about 20 times and hold them,have someone release the bleeders 1 side at a time with the pedal still down,then pump again about 15 times,do the same process,what you want to do is compact the air as far down to the wheel cylinders as possible so when you loosen them more air comes out with the fluid.

Posted on Feb 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Put on new front calipers and hoses whenn bleeding i get fluid but no pedal not enough pressure to move piston in caliper


When you are bleeding brakes, the pressure from the pressed brake pedal is pushing the fluid out the bleeder screw. The caliper piston will not move until you close the bleeder valve and press the brake pedal.

Sep 19, 2017 | Cars & Trucks

1 Answer

I have replaced 3 disc brake calipers on my 2001 pt cruiser. after bleeding all 4 brakes 3 times, I started the car and brake pedal goes to floor. is my brake booster shot?


Michael:

You must start bleeding the brakes at the wheel farthest from the master cylinder (usually the right rear), then the next farthest from the master cylinder, then the next, then the closest. If your master cylinder is at the left front of the car, start with the right rear, then the left rear, then the right front, then the left front. If you don't bleed the brakes in the correct order, you are just shifting the air in the lines from one line to another. Make sure that you close the bleeder before letting the brake pedal up, and the engine should not be running when you bleed the brakes... Make sure that the emergency brake is off. Make sure that the master cylinder does not run out of brake fluid at any time that you are bleeding the brakes.

Jan 24, 2016 | 2001 Chrysler PT Cruiser

4 Answers

Why is my 2003 Chevy Trailblazer brake pedal not releasing?


See if the return spring on the brake pedal is connected or may be stretched. This is a pretty good sized spring that is attached to the pedal arm and connects to the body up under the dash.

Jan 12, 2015 | 2003 Chevrolet Chevrolet TrailBlazer

1 Answer

1999 Ford E350 van problem: brake pedal is soft; have replaced master cylinder, rear wheel cylinders, rear brake shoes and drums, front calipers, rotors and discs; have bled master cylinder before...


Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them.

Feb 23, 2011 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

I replaced the front rotors, calipers and pads. Bled the system but still have no pedal.


If you bleed them correctly,you would have pedal.

You need a helper & the engine running

Did you bleed all 4 wheels?

Feb 23, 2011 | Ford Ranger Cars & Trucks

1 Answer

How to bleed brakes on 1997 Saturn


The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.
  1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
    2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
    3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
    4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
    5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
    6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left front
    3. Left rear
    4. Right front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
    2. Submerge the other end in a transparent container of brake fluid.
    3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
    4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
  3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
zjlimited_349.jpg

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

zjlimited_350.jpg

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

zjlimited_351.jpg

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system





Hope this helps to solve it; remember to rate this answer.

Dec 29, 2010 | 1997 Saturn SL

1 Answer

How do you bleed the abs unit on a 1997 chevrolet truck


start by bleeding the master cylinder bleed the line closest to the fire wall, then proceed to the right rear wheel, left rear wheel, right front wheel, and then the left front wheel.

Sep 16, 2009 | 1997 Chevrolet Malibu

1 Answer

Bleed brakes on 2003 toyota corolla


i try to help you, firts refill brake fluid container,open purge valve in one wheel front only,wait few minutes when drops fluid, close this valve and open other wheel, same procedure, finally repeat this in each 4 wheels

Jul 14, 2009 | 2003 Toyota Corolla

2 Answers

I need to know how to bleed the brakes on a 1999 chevy blazer


Start from right rear, then, left rear, right front, left front. Fill master cylinder. Have helper sit in car, have helper hold brake pedal down. open bleed screw. fluid and air comes out. close screw. release brake pedal. Continue until no air comes out. Move to next wheel. Keep an eye on master cylinder fluid level after each wheel.

Mar 27, 2009 | 1999 Chevrolet Blazer

2 Answers

Just replaced the calipers and blead the brakes. Pedal still travels clear to the floor.


Did you bleed the wheel furthest away from the master cylinder? THen next furthest, to closest last. Did u make sure the master cylinder never got low enough to draw in air? To bleed, Pumo brakes 3x, holding pedal down 1/2 way, while bleeder is opened, let air/fluid flow, shut bleeder as flow diminishes so no air gets in the line. Is the car running when u bleed brakes? It should be. If u are doing all of this u should feel your pedal coming back (getting firm). Let me know how you make out. countrycurt0

Sep 21, 2008 | 1998 Mercury Mystique

Not finding what you are looking for?
1995 Ford Bronco Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...