Question about 2001 Toyota Land Cruiser

1 Answer

I have the exact same problem with my HZJ75, have had injectors and pump reconditioned, checked glow pluga and pre-heater timer, all ok...yet still a struggle to start?? PLEASE CAN ANYONE HELP.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 119 Answers

I thing you repaired old injection pump and injectors
Have you check the pressure from the pump can open the injectors?
I-loose the all injector main pipe from the injection pump only injectors side
2-try to crank the engine just start while engine moving if you see diesel pressure where you loose means injection pump looks good, try to fixed all the pipes while engine cranking if the engine refuse to star injectors needs to resit correct opening pressure.
3-check the injectors pressure follow instruction manual book.
4-Check is any leaks all connections.
5-Check engine compression.

good luck

Posted on Mar 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BMW 320d e46 cranks but won't start.


check the cylinders compression, if below to 95 psi remove the spark plugs then check if wet with fuel ,
if this condition exist , It is very possible that you have to recondition the pistons, rings or cylinders

May 24, 2017 | BMW Cars & Trucks

1 Answer

Where is the glow plug timer relay located please?


PDF]STARTING SYSTEM

www.toyota4wd.dk/Teknik/1PZ-1HZ-1HDT/8-ST.pdf Fixed Delay Type (PZJ, HZJ75, HZB and HDB) ex. (Europe and Australia) . ... PlugRelay. To Alternator. Terminal L. Water. Temp. Sensor. Glow. Plug. Resistor. Glow Plug ... HINT: Refer to Diesel Electrical System Diagnosis for inspection ..

Jul 14, 2015 | 2000 Toyota Land Cruiser

1 Answer

1993 ford f250 7.3 liter diesel starting problems


It is worth ensuring the glow plugs are actually receiving current by attaching a test lamp during the starting process. Heater plug timer relays can cause problems.

A good cranking speed is necessary for good cold starting and also good injector spray patterns and break-off pressures. Bad spray patterns and low pressures, slow cranking and fuel drain-back are common problems.
Low compression pressures can also be a problem. If the other stuff has been checked and found to be ok it is worth having them tested.

Feb 25, 2015 | 1993 Ford F250

2 Answers

90 7.3 ford diesil cranks but wont start start


check for air in the system . Bleed out at all bleed screws . crack the injector lines at the injectors and continue cranking until diesel drips from the nut. tighten and continue cranking. Check for fast crank speed and glo-plug operation

Jan 11, 2014 | Cars & Trucks

1 Answer

Stalling when cold


Have you changed your fuel filter? Pump ok otherwise would be doing it all the time. Injector pump on some of these has a thermal advance solenoid on the side of the pump If so check power going to it Also check glow plugs and after timer

Jul 10, 2009 | 1994 Isuzu Rodeo

4 Answers

I have a Nissan Almera diesel 2,2 liter engine, year 2000. It stopped running just like that, without any pre-announcement. I could not start it (It swings but the engine does not start). The launch X431...


Solution #1 is not correct.. reason, why engine does not start when those codes are shown, is pump control unit (PCU), or electromagnetic valve. You should give PCU to fix (mostly it's broken transistor inside) or to change you current PCU to the new (need to be programed) or buy whole new VP44 PSG5 pump.
Sorry for my broken language :)

Nov 12, 2008 | 1994 Mercedes-Benz C-Class

1 Answer

Hard Start Toyota Landcruiser HZJ75


two first things to check fuel and spark ...fuel make sure your fuel pump is working its messy but the easiest way is to pull the fuel line "only one connection" and turn key to on then press gas pedal and gas should pump out if not fuel pump is bad... if thats not it you want to check for spark easiest way is to pull one of the spark plug wires and stick a screwdriver in the end then hold the screwdriver to where the metal shank is approx. 1/4" away from any metal surface ... hold the screwdriver without touching the metal shank!!! have someone crank the engine you should see a spark intermittently between the screwdriver and the metal youre holding it close to.. if thats ok the only other thing i can suggest is get a battery with more cca "cold cranking amps"..hope this helps..OH YA ON A SAFER NOTE!!!...DONT LOOK FOR SPARK WITH THE ENGINE WET WITH FUEL..

Sep 19, 2008 | 2001 Toyota Land Cruiser

Not finding what you are looking for?
2001 Toyota Land Cruiser Logo

468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...