Question about 1999 Suzuki Grand Vitara

2 Answers

H20A suzuki spark plug gap

H20A suzuki engine - spark plug gap? Lack of power; engine diagnosis clean except for notification that engine is no longer connected to an automatic gearbox (it is a secondhand engine ex Japan). Lack of power was cured by changing plug gap - but what is the correct gap? Correct spark plugs as per bonnet sticker not available in Kenya.
Where can I get workshop manual & engine tuneup data? Chris

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 617 Answers

Gap is 0.039-0.043 [in] ngk bkr6e-11

Posted on Feb 04, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 2,019 Answers

In general, a smaller gap, like .032 inches will give you more power, better starting, especially in cold weather or with a turbo charger.
A larger gap, like .045 inchers will giver you better mileage and better reading on pollution tests.

While the oxygen sensor will pick up on any change in spark plug gap, you can compensate with a variable resistor in series with the oxygen sensor. So you can tweak the power vs mileage any way you want.

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the proper gap for spark plugs for a 2007 Suzuki forenza


open hood, see the sticker there on the hood (up and under)
it tells you 2 things, (at least) engine that is there. unstated
and the spark gap and my state correct plug to use.)
do no use wrong plugs. (magic gap plugs)
is car in usa, you never stated that or engine size.
2.0-liter four-cylinder D-TEC made by General Motors
vin code Z
hard facts from FSM. and from NGK.


26117060-e33baypcl3dkzrss4bzchukk-1-0.jpg

26117060-e33baypcl3dkzrss4bzchukk-1-1.jpg

Mar 04, 2016 | Suzuki Cars & Trucks

2 Answers

I just bought spark plugs, NGK G-Power Platinum alloy. Do I need to gap the plugs and if so how much?


should already be gapped but doesn't hurt to check all of them so all are the same

Aug 17, 2015 | 2007 Suzuki SX4

1 Answer

What is the spark plug gap 3.2 ltr engine


2001 really., that year? wrong year, you did that.
in the usa, (this is a usa forum)
posted 100s of times.
open hood, look up under hood, see that EPA sticker,
showing just that?
the 3.2L was introduced in 2008/9
depends on what plugs, some are not gap settable.
usa spec, 2010.
read this FSM page.
hen servicing an iridium spark plug, do not touch the center electrode. The center electrode on this type of spark plug is slender and can be damaged if a mechanical force is applied. Do not clean or adjust the gap for the iridium spark plugs.
IF NOT THAT THEN,
old technology spark plugs, not above.
The 3.2L engine spark plug air gap specification is: 0.043-0.047 inch (1.1-1.2mm).

Mar 11, 2015 | 2001 Suzuki Grand Vitara

1 Answer

Why would suzuki forenza stall at a stop


Turn the ignition and start the Suzuki Eiger. If the engine has difficulty starting or will not start at all, there may be a problem in the electrical or starting system. Remove the spark plug wire from the spark plug and remove the spark plug from the engine using a spark plug wrench. You can replace the spark plug or use a wire brush and gap tool to clean and re-gap the spark plug. Insert and tighten the spark plug, reattach the spark plug wire and try to restart the engine. Remove the battery cables from the battery and attach a battery meter to the battery. Observe the amount of charge the battery is holding and if the meter has a test feature, test the battery to see if it will dispense the correct amount of power. Clean the battery contacts with a wire brush and reconnect the battery cables. Check the oil, gas, transmission and brake fluid levels on the Suzuki Eiger. If there is not enough gas in the ATV, it will not start. Checking the fluids regularly to see if there are any leaks or if any of the fluids are dangerously low. Top up any fluids that may be low before you use the ATV. Adjust the fuel idle mixture screw on the Suzuki Eiger's carburetor if the engine is running rough. Inspect the air intake and exhaust pipe for the Suzuki Eiger. Any blockage in or on these components can affect engine performance. OBD2 PROMOTION FindOBD2 com

Aug 15, 2014 | Cars & Trucks

1 Answer

HAVE LOW POWER OUTPUT ON MY 2Y FOUR CYLINDER ENGINE WITH A CARBURATOR


I don't know this engine in detail, but we can make a few general statements. In that type of engine, lack of power can be caused by

- a bad spark (check spark plugs for gap and fouling, measure coil resistances, check plug leads)
- lack of fuel (weak fuel pump, blocked filter, blocked jets in carby)
- engine timing off spec (use a timing light to check this)
- lack of compression (use a compression gauge to check this)

Of all these, I'd start with engine timing, then look at a blocked jet in the carby.
-

Jan 01, 2012 | Toyota Pickup Cars & Trucks

1 Answer

My 1998 buick century custom when warm luggs like it has a miss. The electical on dash board are not on, still has power but luggs... please help !


first thing I would do is check all tune up components, distributor cap (worn out or cracked), rotor (worn out) , spark plugs if new check spark plug gap, spark plug wires, check engine timing. if that doesn't solve the problem check engine compression possible blown head gasket or leaking piston rings, check fuel pressure, change out fuel filter. also if your catalytic converter going bad can cause a lack of power.

Dec 17, 2011 | 1998 Buick Century

2 Answers

Battery good starter good but will not start


The two usual reasons a car won't start are either lack of fuel or lack of spark (ignition). Pull a spark plug (pull off the plug wire boot, then get a spark plug socket and a ratchet handle and unscrew the spark plug). Reconnect the plug wire to the spark plug and hold the metal base of the spark plug against the metal valve cover or the engine block (something grounded) while someone else cranks the engine over with the ignition switch for a few seconds. If you don't see a spark jump the gap in the plug, you have an ignition problem. If you do have a spark, it's probably either lack of fuel to the cylinders or a timing problem that is causing the problem.

Jan 30, 2011 | Chevrolet Avalanche Cars & Trucks

2 Answers

How to replace sparl plugs on a Jeep Cherokee?


Hello, I hope this info helps...(subytech1)...REMOVAL
In this engine, each individual spark plug is located under each ignition coil.

  1. Prior to removing spark plug, spray compressed air around base ofignition coil at cylinder head. This will help prevent foreign materialfrom entering combustion chamber.
  2. On this engine each individual ignition coil must be removedto gain access to each spark plug. Refer to Ignition CoilRemoval/Installation.
  3. Check condition of coil O-ring and replace as necessary.
  1. Inspect spark plug condition. Refer to Spark Plug Conditions.
CLEANING
Theplugs may be cleaned using commercially available spark plug cleaningequipment. After cleaning, file center electrode flat with a smallpoint file or jewelers file before adjusting gap.

CAUTION: Never use a motorized wire wheel brush to clean sparkplugs. Metallic deposits will remain on spark plug insulator and willcause plug misfire.

ADJUSTMENT

Setting Spark Plug Gap - Typical
Check spark plug gap with a gap gauge tool. If the gap is not correct,adjust it by bending ground electrode. Never attempt to adjust gap bybending center electrode.

INSTALLATION

CAUTION: This engine is equipped with copper core groundelectrode spark plugs. They must be replaced with the same type/numberspark plug as the original. If another spark plug is substituted,pre-ignition will result.

Special care should be taken when installing spark plugs into cylinderhead spark plug wells. Be sure plugs do not drop into plug wells asground straps may be bent resulting in a change in plug gap, orelectrodes can be damaged.

Always tighten spark plugs to specified torque. Over tightening cancause distortion resulting in a change in spark plug gap or a crackedporcelain insulator.

  1. Start spark plug into cylinder head by hand to avoid cross threading.
  2. Tighten spark plugs to 27 Nm (20 ft. lbs.) torque.
  3. Before installing coil(s), check condition of coil O-ring andreplace as necessary. To aid in coil installation, apply silicone tocoil O-ring.
  4. Install ignition coil(s). Refer to Ignition Coil Removal/Installation.

Aug 07, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Lack of power


These engines are pretty sensitive to the spark plug gap. Try replacing the plugs and making sure the gap is correct (even if they're pre-gapped. They're typically 0.055", but there should be a sticker under the hood that states the actual gap.

Jun 07, 2009 | 1995 Ford Mustang

1 Answer

I'm trying to locate the spark plugs in my suzuki 2008 sx4.


You remove the rectangular plastic cover on top of the engine(2 screws), under that is the plug wires and spark plugs. Pull wires straight up, remove plugs with proper spark plug socket, extension and ratchet, reverse to install.

Platinum plugs are not required but will allow longer change intervals. Check the gap but do not gap them, if they are not properly gapped. Bring them back and asked for new ones.

The metal's on the Platium plugs are harder then copper plugs and can break upon trying or break in your cylinder when in uses.

Good luck and hope this helps

Apr 13, 2009 | 2007 Suzuki SX4

Not finding what you are looking for?
1999 Suzuki Grand Vitara Logo

742 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...