Question about 2001 Dodge Neon

1 Answer

WHEN I TURN ON MY HEAD LIGHTS MY BACK LIGHTS DONT WORK

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

Hi
The back lights have a seperate set of fuse.... please replace this with a new fuse.
Regards
Berry

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I change the switch because my hi bean dont work and know head lights dont work


you haven't wired the switch back up properly
after that the problem might have been a faulty relay for the high beam circuit

Dec 03, 2016 | Cars & Trucks

1 Answer

Head lights


You dont actually replace the headlight , just the bulb inside the headlight.. look inside the engine compartment at the back of the bulb , you just unplug the wire and either turn the bulb 1/4 turn to remove , or there will be a little spring clip.

Apr 14, 2010 | 2004 Chevrolet TrailBlazer

2 Answers

Tail lights and dash lights out


Check the head light switch and the ground of the fuses.

Oct 08, 2009 | 1995 Pontiac Grand Am

1 Answer

HOW DO I CAHNGE MY HEAD LIGHTS ON A 99 BUICK PARK AVENUE.


well u have to take out the head light clips which are on the sides of the head light then pull out the head light and uncover the second rubber cover i believe then reach in the head light and turn the socket to the left and and should come out the just change the bulb...when putting the bulb back just turn it to the right and put back the head light and rubber cover and the side clips and thats it...good luck

Jun 22, 2009 | 1988 Buick Century

1 Answer

Turn signals and back up lights dont work, bulbs and fuses good. Blinker lights only work in dash when emergency flashers are on.


Test the circuit board wires on the back side of your taillights where the bulbs go in to see if power is going there with the blinker on, if yes replace the circuit board (quite common with these trucks). If there is no power back there check your flasher relays for each turn signal, assuming they dont click off and on when you tip the turn lever. if all else fails, head for the multifunction switch behind your steering wheel inside the column that your turn signal/wiper/cruise control lever is connected to.

Mar 06, 2009 | 1991 Chevrolet C1500

4 Answers

Dash and tail lights on a '91 Lincoln Town Car - quit working


From what you just said i dont belive the mechanic checked your fuses correctly.

Check your self to confirm, But if no avial i belive the controller for your lighting may be fried.

Feb 25, 2009 | 1991 Lincoln Town Car

1 Answer

Break light dont work when head lights are on


This is most likely the multifunction switch.

Dec 13, 2008 | 1989 Ford Bronco II

Not finding what you are looking for?
2001 Dodge Neon Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...