Question about 2006 Pontiac Grand Prix

1 Answer

Check engine light on; code indicates secondary air injection system pump stuck on.

Posted by on

  • Thomas Johnson May 11, 2010

    What do you need help with

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

3.1 LTr or 3800 ? secondary air pump should be replaced. www.rockauto.com

Posted on Feb 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code p2445 - how to repair or bypass


P2445 code definition

Secondary Air Injection System Pump Stuck Off Bank 1

What the P2445 code means

The secondary air injection system is designed to pump outside air into the exhaust in order to help reduce harmful emissions. This trouble code indicates that the powertrain control module has detected a malfunction with this system on the bank 1 side of the engine.

What are the causes of the P2445 code?

The most common cause of this trouble code is a failed air injection pump. The air injection pump is designed with a check valve inside which only allows air to flow in one direction, preventing exhaust gases from escaping through the air pump and only allowing air to enter. When this check valve fails, moisture is able to get inside the air pump. During the winter months this moisture can freeze, causing the air pump to seize up and possibly break. Other possible causes of this issue would include damaged wiring or connectors associated with the air pump, blown fuses, or a broken serpentine belt

Oct 18, 2016 | 2005 Toyota Tundra SR5

1 Answer

I have a service engine soon light on and have hooked up an OBD11 reader to it and got code P0410 pertaining to a secondary air injection problem. hoses are fine, pump is new.


P0410 Oldsmobile - Secondary Air Injection System Malfunction

Possible causes: - Faulty Vacuum hoses damaged
- Faulty Air Pump inoperative
- Air bypass solenoid harness is open or shorted
- Air bypass solenoid circuit poor electrical connection
- Air bypass solenoid leaking/blocked or stuck open/closed
- Air diverter valve leaking/blocked or stuck open/closed

Tech notes: Visually inspect AIR pump and AIR bypass valve harness and connector, if connector are OK, then replaced AIR bypass valve.

When is the code detected? The secondary air injection system does not detect the presence of air in the exhaust when introduced by the secondary air injection system.

Possible symptoms: - Engine Light ON (or Service Engine Soon Warning Light)
- Engine hesitation

P0410 Oldsmobile Description An air pump is used on the vehicle to lower tail pipe emissions on start-up. The Powertrain Control Module (PCM) grounds the Air pump relay control circuit which energizes the Air pump. The PCM also grounds the Air combination valve vacuum control solenoid circuit, which energizes the Air vacuum control solenoid. Vacuum is then applied to both Air combination valve diaphragms which opens the shut off valves. The PCM enables both circuits simultaneously when Air system operations id desired. When the AIR system is active, then Air pump forces fresh air into the exhaust stream in order to accelerate catalyst operation. The AIR combination valves replace the conventional check valves. When the AIR system is inactive the shut off valves prevent air flow in either direction.
P0410 Oldsmobile Secondary Air Injection System Malfunction

May 30, 2015 | 2001 Oldsmobile Intrigue

1 Answer

P0410, p2101 and p0014 codes


Possible causes
- Faulty Vacuum hoses damaged
- Faulty Air Pump inoperative
- Air bypass solenoid harness is open or shorted
- Air bypass solenoid circuit poor electrical connection
- Air bypass solenoid leaking/blocked or stuck open/closed
- Air diverter valve leaking/blocked or stuck open/closed
help.jpg What does this mean? When is the code detected?
The secondary air injection system does not detect the presence of air in the exhaust when introduced by the secondary air injection system.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Engine hesitation
P0410 Description
An air pump is used on the vehicle to lower tail pipe emissions on start-up. The Powertrain Control Module (PCM) grounds the Air pump relay control circuit which energizes the Air pump. The PCM also grounds the Air combination valve vacuum control solenoid circuit, which energizes the Air vacuum control solenoid. Vacuum is then applied to both Air combination valve diaphragms which opens the shut off valves. The PCM enables both circuits simultaneously when Air system operations id desired. When the AIR system is active, then Air pump forces fresh air into the exhaust stream in order to accelerate catalyst operation. The AIR combination valves replace the conventional check valves. When the AIR system is inactive the shut off valves prevent air flow in either direction.

Read more: http://engine-codes.com/p0410.html#ixzz31FMsMMLJ

Mar 27, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

Mercedes Benz R 350, 2008 error P0411


Error Code: P0411
Description:
Secondary Air Injection (AIR) System - Incorrect Flow Detected
Indication:
Malfunction Indicator Lamp (MIL) ON.
Reasons:
Secondary air injection (AIR) pump.
Secondary air injection (AIR) valve.
Secondary air injection (AIR) hose(s).

Feb 21, 2014 | 2007 Mercedes-Benz C230 Sedan

1 Answer

I replaced my secondary air check valve on my 2001 chevy tahoe but code 1416 still comes up. what else can i check


here is what i found on p1416.



P1416 Chevrolet
P1416 Chevrolet - Secondary Air Injection System Bank 2
Possible causes
- Faulty Secondary Air Injection (AIR) pump
- Secondary Air Injection check valve bank 2
- Secondary Air Injection (AIR) pump electrical circuit fault
- Blocked Secondary Air Injection (AIR) system

When is the code detected?

The P1416 code is set when no O2 sensor voltage change is detected by the Engine Control Module (ECM).


Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)


P1416 Chevrolet Description
An Secondary Air Injection (AIR) pump is used on this vehicle to lower tail pipe emissions on start-up. The PCM supplies a ground to the AIR pump relay, which energizes the AIR pump. The Powertrain Control Module (PCM) monitors the HO2S voltages to diagnose the AIR system. During the AIR test the PCM activates the AIR pump during closed loop operation. When the AIR is activated, the PCM monitors the HO2S voltages and short term fuel trim values for both banks of the engine. If the AIR system is operating properly, the HO2S voltages should go low and the short term fuel trim should go high.

Jan 23, 2014 | 2001 Chevrolet Tahoe

2 Answers

What does this code mean? P0410


Diagnostic Test Code (DTC) P0410 indicates that your secondary air injection system is not functioning properly.
Not all 2001 Chevrolet Bazers are equipped with secondary air injection. The secondary air injection system was added to vehicles that were to be sold in certain areas where the emissions laws required it, like the State Of California.

The Powertrain Control Module (PCM) monitors the system by commanding the secondary air blower motor to run and the air injection solenoid to open. This causes additional oxygen to enter the exhaust system. The PCM then monitors the signal from the oxygen sensors to see if the commanded air has in fact, entered the exhaust system. Code P0410 sets when the PCM has commanded the blower motor on and the solenoid open and there is little or no change in the oxygen sensor signal.

GM has had some problems with these systems and there has been a Technical Service Bulletin (TSB) issued that addresses some of the known concers. Below is a brief description of the TSB and the issues involved.

Bulletin No.: 04-06-04-015A
Date: November 28, 2006
TECHNICAL
Subject:
LN2, L43 or L35 Engine SES/MIL Light Illuminated, AIR Pump Ingesting Water and DTC P0410 Set (Replace AIR Pump and Inlet Hose Assembly)
Models:
1999-2003 Chevrolet Blazer, S10
1999-2001 GMC Jimmy
1999-2003 GMC Sonoma
1999-2001 Oldsmobile Bravada
with Vortec 2.2L I4 or 4.3L V6 Engine (VINs 4, 5, W - RPOs LN2, L43, L35)
Condition
Some customers may comment on the SES/MIL light being illuminated. Upon investigation, the technician may find a DTC P0410 indicating that there is a concern in the secondary air injection system.
Cause
Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.
Correction
Replace the AIR pump and install a new inlet hose and solenoid tube assembly...

The bulletin goes on and gives detailed information on how to perform the repair and the part numbers of the replacement parts needed to do so. Your local dealer can provide the parts for you and you can probably get them to print out a complete copy of the bulletin for you. It is not really hard to do if you want to do this yourself.

Sep 01, 2011 | 2001 Chevrolet Blazer

2 Answers

Obd code of p0411 on a 1999 ford mustang 3.8 v-6 what do I check to correct


That's s failure of the secondary air pump. It'll have to be changed. It's an emissions component meant to help with cold start emissions. It won't cause engine running trouble but at inspection time you'll fail for smog. Change it before then and you'll be fine.

May 16, 2010 | 1999 Ford Mustang Cobra

2 Answers

Car is choking out and dying. Reads P 0411 code. How do I know if its the motor or just the solenoid valve? How can I check to narrow down what actually is causing the problem? It's on a 2000 VW jetta VR6


16795/P0411/001041


if (window.showTocToggle) { var tocShowText = "show"; var tocHideText = "hide"; showTocToggle(); } 16795/P0411/001041 - Secondary Air Injection System: Incorrect Flow Detected Possible Symptoms
  • Malfunction Indicator Light (MIL) ON
Possible Causes
  • Fuel Pump Relay (J17) faulty
  • Hoses/Pipes to/between Components faulty/clogged
  • Secondary Air Injection Pump (V101) faulty
  • Secondary Air Injection Pump Relay (J299) faulty
  • Secondary Air Injection Solenoid Valve (N112) faulty
Possible Solutions
  • Check Fuel Pump Relay (J17)
  • Check Hoses/Pipes to/between Components
    • Check Secondary Air Injection Hoses/Pipes for Carbonization
  • Check Secondary Air Injection Pump (V101)
  • Check Secondary Air Injection Pump Relay (J299)
  • Check Secondary Air Injection Solenoid Valve (N112)

Apr 28, 2010 | 2000 Volkswagen Jetta TDI

2 Answers

1998 328i.. Got a 1421 and 1423 code...not sure where to start...


1997 BMW 328I 2.8L Customer Concern: MIL is on with trouble codes P1421 and P1423, for incorrect secondary airflow on both cylinder banks. Tests/Procedures: 1. Perform a functional test of the Air Injection Reaction (AIR) system. Tee a vacuum gauge into the vacuum hose attached to the diverter valve, located on the cylinder head towards the front of the engine.

2. Allow the vehicle to sit over night. Start the engine (cold) while monitoring the amount of vacuum on the gauge at startup. At temperatures from -10 to 40 degrees Celsius, there should be at least 17 inches of vacuum. At the same time, the AIR pump should run and pump a large volume of air into the exhaust. Potential Causes: A.I.R. Pump
Air Pump Relay
Restricted Cylinder Head
Diverter Valve
Tech Tips: These codes are related to a problem detected in the Secondary Air Injection system. Scan tools with BMW software include a feature to command the AIR pump on and off. The pattern failures for these codes are the AIR pumps due to leaks in the diverter valve and moisture or condensation in the AIR pump.

Possible fix but not all items. Just areas to look at:
Confirmed Fix - A.I.R. Pump - A.I.R. Diverter - A.I.R. Pump, Air Injection Reaction Diverter (AIRD) Valve - Air Injection Reaction Diverter (AIRD) Valve - Check Valve, Secondary Air Pump - Diverter Valve Vacuum Lines

Jul 04, 2009 | 1997 BMW 328

1 Answer

Get diagnostic code of P0410


Secondary Air Intake System Fault code P0410 is set by a defective air injection pump, this pump is electric, on older cars it was called a "SMOG PUMP" and was belt driven by the engine. On cold start do you hear a hair dryer type noise from under the hood? if not the pump has failed, if you do the check valve is stuck closed, the only way to fix either issue is a new secondary air injection pump.

Aug 21, 2008 | Volvo XC70 Cars & Trucks

Not finding what you are looking for?
2006 Pontiac Grand Prix Logo

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...