Question about 1990 Nissan Stanza

1 Answer

How to change out an ignition switch? any help would be appreciated

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 86 Answers

The bolts that hold it in place need to be removed with a punch or chisel. The heads break off during installation for security purposes.

Posted on Feb 04, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2001 Chrysler PT Cruiser no power to fuel pump changed PCM put power to relay still nothing any help would be appreciated thanks

I think there is a fuse that protects the relay, otherwise the ignition switch may be bad not allowing current to the relay.

Dec 19, 2017 | Chrysler Cars & Trucks

1 Answer

My 2007 Chevy Silverado lt new body I put my key in ,turned it key broke can't get key out how can I change the ignition switch if I can't put in on position any help I'd appreciate it

You could try a very tiny dot of super glue on both pieces of the key. If you get it just right, you should be able to pull that key back out, without having to replace the ignition.

Dec 24, 2016 | Cars & Trucks

1 Answer

Engine dies at random. Just replaced ignition switch!

i jest had the same problem chang out the 02 that fixed mine

Apr 10, 2012 | 1998 Honda Accord

1 Answer

When i turn the key off the switch wont go all the way to the lock position to get the key out

If your shifter is all the way up, your going to have to change the ignition switch and the lock cylinder. There is no other way around it. It sucks. I had to change mine a year ago. 320 for the ignition and 200 for the labor. If you have a question, just let me know. I am here to help. Sorry about the bad news my friend. 4 thumbs up is appreciated if you appreciate the reply. Your best bet is going to a junkyard and doing it yourself. It would save you hundreds. Take care.

Feb 25, 2011 | 2000 Pontiac Grand Prix

2 Answers

No spark

There's no emergence switch, if there was it would only be for fuel and not spark, there four thing to get spark,
ignition control module, ignition coil, distributor pick up assembly and spark plug wire's check for spark at coil, more then likely it's going to be your distributor pick up assembly, the pick up sit in side your ignition distributor, replace it and it will start, hope this was very helpful.

May 19, 2010 | 1985 Ford F 250

1 Answer

Changing the ignition in a 1995 Nissan 200SX

this is not a job a novice really should tackle as you can do a lot of damage to all the other switches located in the steering column. You should call a locksmith or have the car towed to an auto repair shop and have them change the switch.

May 04, 2009 | Mercury Cougar Cars & Trucks

2 Answers

Starts then dies imediately after starting.

It could be a defective ignition switch.

Apr 27, 2009 | 2000 Nissan Pathfinder

1 Answer

Ignition switch

Need to disconnect battery, then remove airbag, the steering wheel (mark before removal), then remove top and bottom sheering column covers, then the spiral spring. At this point you will have access to the housing where the ignition switch is mounted. there is a breakaway bolt that secures this to the steering wheel. Can use an air hammer and gently loosen. Then you disconnect the harnesses from behind. Continue by sliding the housing off and then you will have access to the screw that secures ignition switch in place.
Install is the reverse.

Jul 19, 2017 | 1994 Volkswagen Jetta

3 Answers

Won't start


Sep 11, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1990 Nissan Stanza Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

78267 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides