Question about Toyota Camry

1 Answer

I need to know what fuse or relay is for the running lights ??????

Posted by on

  • 1 more comment 
  • jlb41461 Feb 04, 2010

    but what relay do I change ...... I have the lid to the fuse box, and cant figure what one to change

  • jlb41461 Feb 04, 2010

    no tail lights or running lights .... have head lights turn sigs and hazards .... no running lights

  • jlb41461 Feb 04, 2010

    is it the one that just says "Head" ???

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 19,396 Answers

Hi.


Check the tail lights. If the tail lights are OK, then check only the fuse.

If the tail lights are off , replace also the relay.

The relay is located in the engine compartment, in the box on one side.

The fuse is in the same box in US model , but in Canadian model you need to look in the box at the front.

See the diagram below:
I need to know what - 3025a81.gif

Posted on Feb 04, 2010

Testimonial: "sorry ..... I know where the fuse box is I need to know what one to change ???????"

  • Ginko
    Ginko Feb 04, 2010

    Yes it is. That was no reason for voting inappropriate.


    Sorry and goodbye.


    G.

  • Ginko
    Ginko Feb 04, 2010

    I will be grateful if you change the negative rating given. This was not a chat were we answer in real time, and you have it refunded.




    Thanks and goodbye.




    G.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse located for the daytime running lights on a 2005 Chev Siveraado?


It is located in the underhood fuse/relay box , marked DRL 10 amp fuse ! Also if that is good check the DRL relay in the same fuse/relay box .Your light sensor could also be bad .
The daytime running lamps (DRL) will operate when the ignition switch is in the RUN position, for automatic transmissions (A/T), the gear selector is not in the PARK position, the headlamp switch is in the AUTO position, and for manual transmissions (M/T), the park brake is released. When these conditions have been met and the ambient light sensor indicates daytime conditions, the DRL will illuminate. The ambient light sensor is a light sensitive transistor that varies its voltage signal to the body control module (BCM) in response to changes to the outside (ambient) light level. When the BCM receives this signal it will either turn on the DRL or the headlamps for auto headlamp operation. Any function or condition that turns on the headlights will cancel the daytime running lamps operation. The DRL can be manually turned OFF by depressing the AHL/DRL switch in the headlamp switch
Do you know that on inside of fuse box lid it shows what fuse is what .

Feb 01, 2016 | 2005 Chevrolet Silverado

1 Answer

Which fuse is for the daytime running lights for a 2005 Chevy Siverado?


The DRL 10-amp fuse in the underhood fuse block supplies battery positive voltage to the DRL relay switch contacts and relay coil. When the BCM energizes the DRL relay , the DRL receive voltage on the DRL supply voltage circuit.

Feb 01, 2016 | 2005 Chevrolet Silverado

1 Answer

I need a diagram for a 2001 VW Cabrio relay. I thought number 6 was for the blinkers/hazards but it's not and its empty. 413 is in there and blinkers and hazards just stopped one day. I don't know if I...


A2Resource
a great vw resource site
25345733-zc0klvszlbpkidh1d23fhked-5-0_0.gif
Relays:
Num.Relay Arrangement and Pinout (with control number stamped on relay)
1A/C Relay (13 or 140)
1A/C Switch
2Radiator Cooling Fan
3Fan Switch High Speed
4Battery, Fuse 23
5A/C Clutch (via pressure and temperature switches)
6Main Fusebox Battery Power, Fuse 19
7Main Fusebox Ground
8Fresh Air Fan
2Rear Wiper Relay (72)
1Main Fusebox Ground
2Main Fusebox Run Power, Fuse 4
3Rear Wiper Motor
4Wipe/Wash Signal from Switch
3Digifant Control Unit (30 or 32), Motronic OBD1 Control Unit (109)
1Main Fusebox Ground
2Tachometer
3Main Fusebox Start/Run Power
4Main Fusebox Battery Power
5To ECU (relay ) (1990 G60, ABA/VR6 OBD1 only)
6To ECU and Engine Electronics
4Load Reduction Relay (18)
1From Ignition Switch Run Power
2To Main Fuse Box Run Power
3Main Fusebox Battery Power
4Main Fusebox Ground
5Low Coolant Level Control Unit (43)
1Main Fusebox Start/Run Power
2Low Coolant Level Sensor
3Coolant Temperature Sensor, Gauge
4Main Fusebox Ground
6Flashers (21)
1Main Fusebox Ground
2Flasher Output
3Flasher Input/Power
4X/6 (Trailer Light)
7Headlight Washer (33)
1Main Fusebox Ground (B/4 to C/3 to Ground)
2Headlight Washer Pump
3Headlight Switch Pin 56 (headlights) (B3 to D4 to light power)
4Main Fusebox Battery Power (B/5 to Y/2)
5Windshield Washer Pump (B/1 to B/2 to washer pump power)
8Wash/Wipe/Intermittent Relay (19 for standard relay, 99 for variable intermittent module)
1Main Fusebox Ground
2Intermittent Switch
3Main Fusebox Run Power, Fuse 5
4Park/Low Signal (ground when parked, positive when on low speed)
5Wiper Motor Low Speed Output
6Wash Switch (positive for front wash)
9Seat Belt Warning Control Unit (4 or 29)
1Main Fusebox Ground
2Seat Belt Switch
3Door Switch
4Seatbelt Light
5"Key In" Power from Ignition Switch
6Main Fusebox Start/Run Power
7Automatic Shoulder Belt Controller
9Radio/Lights Buzzer (36)
1Main Fusebox Ground (not used)
2A1/4 (Left Parking Lights)
3Vehicle Speed Sensor
4Seatbelt Light (not used)
5"Key In" Power from Ignition Switch
6Main Fusebox Start/Run Power (not used)
7A2/2 (Right Parking Lights)
10Fog Light Relay (110 for fog lights with low beam headlights only, 53 for parking light/high beam fog lights)
1Parking Light Power
2Headlight Switch Headlight Power (Low/High)
3Fog Light Switch Power, Fuse 10
4Main Fusebox Battery Power
5Main Fusebox Ground
6Low Beam Headlight Power
11Horn (53)
1Main Fusebox Start/Run Power
2To Horns
3Main Fusebox Ground
4From Horn Button
12Fuel Pump Relay (80, 67 or 167)
1Main Fusebox Starter Power (not used)
2Main Fusebox Start/Run Power
3To ECU (Fuel Pump )
4To Fuse 18, Fuel Pump, Oxygen Sensor Heater
5G2/6 (not used)
6Main Fusebox Battery Power From 30B
7G2/7, T1 (not used)
8Main Fusebox Ground (not used)
9M/4, U1/8, G2/5 (not used)
12Glow Plug Relay (102 or 104)
1Main Fusebox Starter Power
2Main Fusebox Start/Run Power
3Engine Temp Sender (preheat)
4Glow Plugs (Z1)To Fuse 18 (not used)
5G2/6 (not used)
6Main Fusebox Battery Power From 30B
7G2/7, T1 (not used)
8Main Fusebox Ground
9Water Separator, Glow Plug Light

remember to check out the website below for more help
http://www.xjamiex.com/mk2resource/electrical/CE2.html

Dec 30, 2014 | Cars & Trucks

2 Answers

Nissan avenir dash lights


There is a fuse for the warning lights and gauges. Yes, you checked the fuses and relays, but you need to check if power is there at the fuse, with the key in the on position.

Here's how turning the key to on causes the warning lights and gauges to turn on: From your ignition switch the on or run wire out of it will have power with key on. The run wire will also send power to the part of the fuse panel that is of the category "hot in run or on", where your fuse for the dash warn. lts. & gauges is- it may be labeled "meter" or "gauges" or like that. From the fuse, a hot wire goes into the harness for the instrument cluster-for the warning lights and gauges. The wire, like the fuse, is only hot in on or run.

The ignition's run wire may splice with a direct connection to some fuses, or more likely there may be an "ignition relay" that powers the "hot in run or on" fuses, and the run wire is used to turn the relay on. You could look for this relay just above or around the fuse panel under the dash. But the easiest place to start is to see if the fuse for the gauges has power to it with the key in on. If it does, the problem is up further on at the cluster connection or a ground for the gauges and cluster. If the fuse has no power available, then the problem is between the ignition switch and the fuse panel. That could be a faulty ignition relay.

Jan 09, 2014 | Cars & Trucks

1 Answer

I need a fuse and relay diagram for a 1989 Fleetwood.


mmaybe go to an auto recking yard you may find a cover there, or try each fuse inavidualy,

Sep 20, 2012 | 1989 Cadillac Fleetwood

1 Answer

Installed a brake controller and the green light won't go on. I am told I need to add a fuse where is the fuse box to add the fuse so that the system recognizes the brake controller in a 2002 Eddie...


Hi, this may true if you connected the trailer brake to the connector on the factory wiring harness. There are several fuses that are needed for trailer towing. In the box by the battery, fuses 13, 25, 27, 53, and 54 are needed. You will need a relay in relay slot 19 for the trailer running lights, a relay in relay slot 20 to charge the trailer emergency battery; and, if your trailer has backup lights (6 or 7 wire connector), you will also need a relay in the relay slot 15. If you did not use the factory connector for your trailer brake controller, check to make sure you have connected the controller to an appropriate power source in the truck. Please let me know if you have questions, and thanks for using FixYa.

Jun 22, 2011 | Ford Explorer Cars & Trucks

1 Answer

I need to know were to find the DRL Module for a 2003 F-150 4x4. My hi and low beem lights work ok , and the auto light sencor works . Its that my Day time running lights do not come on .


The wiring diagram does not show a stand alone drl module for the 03 f150. However it shows 2 drl
relays located in aux. relay box #2 located behind the right side of the dash, left of the glove box.
Also there is the drl resistor located behind the grill, right of the left headlight. Relay #1 is fused at
fuse #5-15a in the fuse block under the left dash. Relay #2 uses fuse #26-10a under left of dash.
Hope this helps.

Nov 17, 2010 | Ford F-150 Cars & Trucks

1 Answer

Need to know what fuse or relay is for the running lights


Hello! Under hood...located in front of the air filter housing...Left front of vehicle is the fuse box...DRL fuse #2 (5amp) powers the running lights...


Guru...............saailer

Feb 04, 2010 | 1999 Toyota Camry

2 Answers

1998 olds were is the light relay found


Your day time running lamp relay is located in the fuse box under the hood. Remove the fuse box cover and on the bottom of the cover you will see a fuse and relay diagram.
Good luck, let me know.
Regards,

May 08, 2009 | 1998 Oldsmobile Achieva

3 Answers

Cruise control


Under the hood is a relay box and after you take the lid off of this relay box it will tell you inside the lid which relay is for what thanks jerry holler if you need more.

Feb 07, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...