Question about 1998 Chevrolet S-10 Pickup

1 Answer

I need a wire diagram for 1998 blazer fuel injection. I believe the injector ground wire might be corroded. Where is that ground wire?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 102 Answers

Haynes Manual 24071 includes wire diagrams for all components. On the injector you have a pink and dark blue wire both are hot and signal wires. The only ground in the system is on the fuel pump and sender unit. Diagram 12-26 in the haynes maual.

Posted on Feb 04, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1998 chevy blazer fuel pump is putting out 55 psi but no gas is getting to the cylinders

4.3 TBI (throttle body injector) You dont have a TBI you should be equipt with a CSFI people in the field call this the spider injector,they inject fuel into tubes for each cylinder , as for the fuel pressure it should be 54 psi to 60 psi,and this is for a 4.3, The CSFI system does plug up which causes rough idle due to the poppet valve or seat,to stick open or closed,Ive ran fuel injector cleaner that has been sucesfull maybe you can try that

Nov 08, 2012 | Cars & Trucks

2 Answers

I have a 94 s10 blazer 4x4 that has the 4.3 spider injection and its not get any fuel !

So, injectors are not firing, right? Is there power on the pink injector wire? If you put an ac voltmeter on any of the injector connectors while cranking, do you see ac voltage?

Jul 31, 2017 | 1994 Chevrolet S-10

1 Answer

93 vortec V6 4.3L No start. New CPI, New ECM,New Distributor,New Coil,

Right at the coil is the ICM (ignition control module) These wire are known for poor male to female connection have some one crank it and you wiggle it to make contact,Also where the battery is is a power ground if that ground is corroded it will give code P1355.

Mar 29, 2012 | 1993 Chevrolet S-10 Blazer

1 Answer

I need a wiring diagram for a 1998 Chevy Blazer fuel pump

The fuel pump assembly consists of fuel pump relay,fuel sensor,the fuel pump controlling fuse,its ECM B fuse. The fuel pump and oil pressure switch. ----------- For its wiring diagram, click the link below and refer the diagram:--- ----------- This should help.Thanks.Helpmech.

Oct 06, 2011 | 1998 Chevrolet Blazer

1 Answer

Hello - have a 1998 chevy blazer with a p0301 code. Know that cylinder 1 is the problem. New plug on cyl 1, and know it's not the wire. Also put new cap and rotor on. Any suggestions on what to do next?

If your Blazer has a "VORTEX" engine, the the fuel injection system will cause this DTC. Under the intake plenum ( that big plastic cover) is a spider legs injection system. that is one main body and up to eight legs that simply clip into the heads. Over time, crud gets into the passage that the injector goes into and causes the tip(s) to get dirty and the only way to clean it is to remove the system and clean all the tips.

Mar 24, 2011 | 1998 Chevrolet Blazer

2 Answers

My 1998 Chevy Blazer crank excessively when I try to start it. It always starts, and runs good when I get it started, but I would really like a smooth start. I have recently changed the fuel filter, spark...

leaky injector/s is flooding motor, mechanically clean or replace. And clean throttle body while you are at it with spray cleaner. Should be almost spotless where large throttle valve opens and closes.

Oct 21, 2010 | 1998 Chevrolet Blazer

1 Answer

We can not understand why it cant get fuel to the injectors

Have you tested out the fuel pump? check for plugged fuel filter?
plugged fuel lines to the fuel rail, injection pulse at the injectors? power to the fuel pump relay? grounds needed to make certain systems work must check those also. get a wiring diagram of the fuel supply system and back trace all the wiring and see if you have power and ground and signal.

Aug 28, 2010 | 1986 Cadillac DeVille

2 Answers

My 96 chevy blazer has a code ''random 4 misfire'' only misses when in park or idleing at a light. is this and injector issue?

my 96 blazer would have random missfires.... sometimes more than one cylinder at a time... there are a few things to try.... 96 vortecs still used distributor caps... but they had such a high intensity spark that they were well noted for frying distributor caps and ignition coils... i would start there... also a few times i had to replace the crankshaft timing sensor.... it could be something as small as a spark plug wire... i would start with the ignition before spending money to check the fuel system

Jun 13, 2009 | 1996 Chevrolet Blazer

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides