Question about 1991 Peugeot 405

1 Answer

Fan not working on peugeot 307 02reg . works sometimes then goes off I think its just a loose wire but where is the wiring ? is it behind the central column ? could it be a wire from the fan under the bonnet ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,098 Answers

Hi I would check the wire under the bonnet, they sometimes touch the exhaust and melt. normally when a fan go's on for a short while then cuts out you would need a new fan, if it is staying on for longer than 1 to 2 minutes then it is most likely a wire. follow the wire back from the fan to check for any suspect bad connections.

Hope this helps

Regards

Dan

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

PEUGEOT 307 FUSE KEEPS BLOWING (abs faults, horn doesnt work)


i have a peugeot 307 number 8 fuse keeps blowing so i have to keep changing the 20 amp fuse please help me i am trying to find out what is causing this

Dec 07, 2012 | 2002 Peugeot 307

1 Answer

Peugeot 306 central locking fault, it goes up and down 7 times every 2-3mins. when you unlock with pid it locks down again straight away. please help?


These have a problem with the wires in the hinge area on the drivers door, click the latch so the door thinks it is shut, do what you do to get the problem and if you still get it then wiggle the rubber tube carrying the wires in the hinge area. If the problem is gone with the door open or you change it by wiggling then the wores have cracked and need fixing, peugeot used to sell a harness part.

Dec 24, 2010 | 1989 Peugeot 405

1 Answer

Where is the air con relay located - 2000 Peugeot 206 1.6 petrol


if you mean the one thay controls the cooling fan then there is 2 of them located at the front of the car next to the cooling fan. these are probably behind a cover and are green in colour and have 5 pins and the wiring usually corrodes where it goes in to the plugs

if this was any help let me know
cheers
mike

May 02, 2010 | 2005 Peugeot 405

1 Answer

Peugeot 306 diesel red stop light is on and both fans run


there are 2 relays inbetween the 2 fans behind the front grill the wiring to the relays tend to corrode.
what you need to do is replace both relays and the wiring conectors

Dec 02, 2009 | Peugeot 405 Cars & Trucks

1 Answer

I have a 1999 peugeot 306, the ventillation/


renew the whole unit ,the resistor in the motor unit is finished ,the thin wire is controling the feed into the motor via a earth resistance in the ballast resistor ,hence variable speed .But you should have a 12v supply via the red cable if you havent then thats your problem ,a loose connector ?? fuse ,fuse holder, broken wire

Sep 10, 2009 | 1991 Peugeot 405

1 Answer

All my lights at the front apart from one main beam are not working iv changed the bolbs still nothing checked the fuse box every think seems fine its for a peugeot 206 1.1 petrol x reg


Check the wiring for loose connections or bad wires etcthen tape them up check wiring for lights and coming off the lights. Good luck and be careful.

Apr 25, 2009 | 1991 Peugeot 405

1 Answer

I have got a peugeot 406 1.9 gldt on an n plate


check the wiring to the heater motor and the reostat, they are known for the connectors melting. also the reostat may be blown (the reostat is a number of resistors that control the fan speed)

Apr 09, 2009 | 1991 Peugeot 405

3 Answers

The electric windows on my peugeot 306 don't work


Hi,
It sounds like a power supply problem. I can't see all 4 motors broken.
First how does the switch "feel" No buttons loose?
Does it illuminate when you switch sidelights on?
If that's ok
I would gain access to the master switch on the drivers door.
I would think you have to remove the door panel and armrest I can't remember for sure, but it doesn't take a lot .
Check and make sure all the multiplugs are connected first of all.
Make sure all the terminals in the plugs are fully "home"
If there is nothing obvious i would follow the loom to where it exits the door and goes back into the car and check for damage.
Check for ANY other electrical equipment not working, if so go back to your handbook and re-check which fuse it goes through.
Also, if this problem has occurred after a recent repair, I suggest you return to the repairer.

Dec 28, 2008 | 1989 Peugeot 405

4 Answers

Heater blower motor sometimes works


where is the motor as i think its burnt out.

Nov 11, 2008 | 1999 GMC Jimmy

6 Answers

Peugeot 307 heater blower fault


Hi
i just had the same fault, but being in the trade it is normally only 1 of 2 problems.
the heater resitor packing up or the wiring loom.
both can be bought through peugeot.
try the heater resistor first (£40). to find it undo 7 star screws to remove glove box then look in behind centre conlsole near back of radio diconnect the black plug with a red and black cable. twist back of fan motor clockwise and remove fan(it's a bit of a tight squeeze to remove),then put your hand inside the hole you just made till you feel the flat resistor turn this anti-clockwise and disconnect green plug then reassemble as removed,

if this does not fix it then it is the loom, to remove this it is best to follow the wires from the back of fan motor up to where i think if i remember lead to 2 other plugs 1 green and 1 black on the way to another green plug up behind the drivers foot well, then thread the new loom back the same way.

on the 405 i think the resistor is in behind the fan motor accessed throgh the driver side footwell again you need to first take out the fan motor normally twisted anti-clockwise. it is un common for 405 to burn out heat resistors it is normally down to a wire fault.

hope this helps

Oct 04, 2008 | Peugeot 307 Cars & Trucks

Not finding what you are looking for?
1991 Peugeot 405 Logo

Related Topics:

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

scj103

Level 2 Expert

81 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...