Question about 1996 Honda Accord

1 Answer

Well my signal lights stopped working all of a sudden I changed the flasher relay and checked the fuses they are good i even tryed to swap a new signal lever switch and they still don't work i could use some help

Posted by on

  • mike watson
    mike watson May 11, 2010

    did you try checking the bulbs?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 435 Answers

Check the connection well there is a loose connection in.to current is passing through .

Posted on Feb 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of flasher relay in a 1998 GMC Sierra


There's always a box with relays black with clips you take off to check..

Mar 23, 2016 | 1998 GMC Sierra

1 Answer

New flasher relay good fuse no four way flasher no turn signals


you need to check the bulbs holders and wiring even a blown bulb will not blow the fuse and an damaged wire or bulb holder will as it will make earth and live go together. there are also fuses for left side and right side turning lights cannot remember rating think they are 10amp.

Mar 19, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Turn signals stopped working. Fuses are all ok,


sounds like the flasher can might have stopped working, you will need to get it replaced, it regulates the indicaters to blink, when it goes the circuit is gone, time for replacing id say. check the relays in the main fuse box under the bonnet first, try swapping the relay with another one like the horn relay just to test that first.

Jun 21, 2010 | 1999 Cadillac DeVille

2 Answers

My hazred lights come on but my tune signal will not


check the fuse first!! then check the flasher relay located in the fuse box under driverside of dash

Jan 22, 2010 | 1993 Ford Crown Victoria

1 Answer

Turning Lights Not Working


If you put a 2 element bulb in a single bulb elemet socket you would or could destroy the flasher unit. Especially if it is a electronic flasher try replaceing the flasher but get mechanicl flasher they last longer.

Jul 09, 2009 | 1998 Toyota Sienna

1 Answer

Turn Signals & Brake Lights Stopped Working


Check the flasher and brake light relays. Check relays under hood in electrical box to make sure they are seated properly and not loose.

Jun 02, 2009 | 1999 Chevrolet Cavalier

2 Answers

1993 Dodge Shadow...left turn signal won't flash


If the fuses are good and the front and rear bulbs are good, change the flasher for the turn signals, even tho the right is working. If that doesn't fix the problem, it might be in the turn sgnal switch on the steering column.
If both bulbs are good for the backup lights and fuses are good, then the backup light switch, which is screwed into the side of the transmission has to bad.

Apr 12, 2009 | 1993 Dodge Shadow

1 Answer

Turn signals and flashers


Hello I had the same problem on my 04 monte. After changing bulbs ,checking wires etc. I finally took it to the dealer and they found out it was the hazard switch. After swapping it with a new one all lights, dash etc started working again and have not had another problem

Aug 17, 2008 | 2004 Chevrolet Monte Carlo

1 Answer

2004 wrangler blinker problem


What other problem did you have before the signals quit? Something that stopped all functions from the signals has to be either a feed or ground IF the flasher is good. Signals feed. Hot wire from the flasher 1 and it should blink underload, but not with a test light or DVM. In other words using a test light the flasher wire should be powered steady. All the rest of the switch is switchable. You should also get a hot wire when the brake pedal is pushed. Check for power at the brake switch,key off.

May 14, 2008 | 2005 AMC Wrangler

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...