Question about 1996 Nissan Maxima

1 Answer

Cant get light off replaced evap solenoid and absolute pressure sensor and everything related to emission control system it failed at inspection now i need to know how to reset the check engine light

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 122 Answers

Try removing the negative on the battery, wait a few minutes and re-install. If that won't work, you'll have to buy, rent or borrow someones code scanner that has the "code clearing" function. Though, if you clear it and 10 minutes late it comes back, then you still have a problem.

Hope this helps

Posted on Feb 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What hoses do I check for check engine light code Po455


DTC P0455 Evaporative Emissions (EVAP) System Large Leak
The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge solenoid valve OPEN and the EVAP canister vent solenoid valve CLOSED . This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. If the system is unable to achieve the calibrated vacuum level, or the vacuum level decreases too rapidly, this DTC sets.
There's more to it that just checking a hose ! Smoke testing the EVAP system is the best way to find leaks .
  1. Inspect the Evaporative Emission (EVAP) System for the following conditions:
  2. ?€¢
    A loose, missing, or damaged service port schrader valve


    ?€¢
    A loose, incorrect, missing, or damaged fuel fill cap


    ?€¢
    A damaged EVAP canister purge solenoid valve

  3. Raise the vehicle on a hoist. Refer to Lifting and Jacking the Vehicle in General Information.
  4. Inspect the EVAP system for the following conditions:
?€¢
Any disconnected, improperly routed, kinked, or damaged EVAP pipes and hoses


?€¢
A damaged EVAP canister vent solenoid valve or EVAP canister

Your best bet is take your vehicle to a ASE certified repair shop or the dealer , where they have the tools an knowledge .

Apr 16, 2016 | 2005 Chevrolet Chevrolet Classic Base

1 Answer

My 00 xterra had a code of po446


Trouble Code: P0446

EVAP Vent Control Solenoid Circuit Malfunction

Possible Causes:


Vent solenoid circuit open, shorted to ground or to power (B+).Vent control solenoid is damaged or has failed..PCM has failed.TSB 00-060 (7/00) contains information related to this code.Trouble Code: P0455

EVAP System Gross Leak (0.080") Detected

Possible Causes:


.EVAP control system pressure sensor is damaged or has failed.EVAP purge solenoid or canister vacuum line loose or off.EVAP purge solenoid is damaged or has failed.EVAP emission canister is dirty, restricted or full of water.EVAP canister vent control valve is damaged or has failed.Fuel tank cap loose, missing or it is the wrong part number.Fuel tank temperature sensor is damaged or has failed.Fuel tank vacuum relief valve is damaged or has failed.Large leak in the EVAP canister or in the fuel tank area.ORVR system is damaged or has a large leak in a component.Refueling control valve is damaged or has failed.Vacuum hose leaking between intake manifold and Purge valve.Here are the codes,take part back and get refund.

Dec 03, 2012 | Cars & Trucks

1 Answer

Emission failure on 2001 chevy blazer 4.3-


your vehicle has a vent valve solenoid located on the evap canister under the back end of the vehicle. You most likely have a bad vaccuum line going to the evap caniser. Have the vehicle smoke tested to verify. If no leaks are found replace the vent valve solenoid

Oct 25, 2012 | Chevrolet Blazer Cars & Trucks

2 Answers

2001 chevrolet sububban po446,452,and 453 how do i fix my check engine light is on and i cant pass in spection


DTC P0446 - Evaporative Emmission Control System Vent Control Circuit
Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test. A code P0446 could mean one or more of the following has happened:
  • Faulty vent valve
  • Open, short or excessive resistance on Vent valve control circuit
  • Blockage of vent valve
  • Bad PCM
Possible Solutions
  • Replace Vent valve
  • Repair open, short, or resistance problem in control circuit
  • Repair open, or short, or resistance problem in power circuit
  • Replace PCM

DTC P0452 - Evaporative emission control system, pressure sensor low imput
DTC P0453 - Evaporative emission control system, pressure sensor high imput

The PCM monitors the EVAP control system FTP sensor input signal to the PCM. The test fails when the signal average jumps above a minimum allowable calibrated parameter. If both codes are present, it sounds like your fuel tank pressure sensor has failed.

The sensor is on top of the tank and you will have to remove the tank. But your symptoms are pointing to more than just the sensor. You may have wiring problems.


Hope this helps (remember to rate and leave a comment about this free answer).

Sep 30, 2011 | 1998 Cadillac Seville

1 Answer

My 2004 Mazda 3 GT 2.3L is getting a P0446 DTC and is burning through a tank of gas in about 2-3 days depending on the amount of driving being done. My Mazda dealer believes that it may be the fuel pump,...


P0446- Evaporative Emissions Control System Vent Control Circuit Malfunction

Possible Causes:
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve

Code is detected when VSV for pressure switching valve is ON, ECM judges that there is no continuity between vapor pressure sensor, fuel tank and charcoal canister (2 trip detection logic)

The vapor pressure sensor, Voltage Solenoide Valve (VSV) for EVAP, Voltage Solenoide Valve (VSV) for canister closed valve (CCV) and Valve Solenoide Valve (VSV) for pressure switching valve are used to detect abnormalities in the evaporative emission control system.

The ECM decides whether there is an abnormality in the evaporative emission control system based on the vapor pressure sensor signal.

Diagnostic Trouble Code (DTC) P0446 is recorded by the ECM when there is a malfunction in either the VSV for EVAP, the VSV for pressure switching valve, or in the vapor pressure sensor itself, or when evaporative emissions leak from the components within the dotted line in Fig. 1 below.
evaporative_evap_system_toyota.gif
The ECM closes the CCV and opens the VSV for pressure switching valve causing vacuum to increase in the entire EVAP system.

The ECM continues to operate the VSV for EVAP until the vacuum is increased to a specified point at which time the ECM closes the VSV for EVAP.

If the vacuum did not increase, or if the vacuum increased beyond the specified limit, the ECM judges the VSV for EVAP and related components to be faulty.

Aug 26, 2011 | Mazda MAZDA3 Cars & Trucks

2 Answers

I have a code P1447 Evap purge flow monitor on my 97 Pathfinder. What is and how do I correct this issue?


P1447 - Evaporative Emission (EVAP) Control System, Purge Flow Monitor
In this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions. Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP canister purge volume control solenoid valve is open to admit purge flow. Purge flow exposes the EVAP control system pressure sensor to intake manifold vacuum.

Under normal conditions (non-closed throttle), sensor output voltage indicates if pressure drop and purge flow are adequate. If not, a fault is determined. Malfunction is detected when EVAP control system does not operate properly, EVAP control system has a leak between intake manifold and EVAP control system pressure sensor.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
* EVAP canister purge volume control solenoid valve stuck closed
* EVAP control system pressure sensor and the circuit
* Loose, disconnected or improper connection of rubber tube
* Blocked rubber tube
* Cracked EVAP canister
* EVAP canister purge volume control solenoid valve circuit
* Closed throttle position switch
* Blocked purge port
* Closed throttle position switch


Test is and send us your updated.

Jan 14, 2011 | 1998 Nissan Pathfinder

2 Answers

Codigo p1440


EVAP System Vent Circuit Malfunction

This diagnosis detects leaks in the Evaporative Emission (EVAP) purge line using of vapor pressure in the fuel tank. The EVAP canister vent control valve is closed to shut the EVAP purge line. The vacuum cut valve bypass valve will then be opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP control system pressure sensor can now monitor the pressure inside the fuel tank. If pressure increases, the Engine Control Module (ECM) will check for leaks in the line between the vacuum cut valve and EVAP canister purge volume control solenoid valve.

Possible causes
- Incorrect fuel tank vacuum relief valve
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Leak is in line between intake manifold and EVAP canister purge volume control solenoid valve
- Foreign matter caught in EVAP canister vent control valve
- EVAP canister or fuel tank leaks
- EVAP purge line (pipe and rubber tube) leaks
- EVAP purge line rubber tube bent
- Blocked or bent rubber tube to EVAP control system pressure sensor
- Loose or disconnected rubber tube
- EVAP canister vent control valve and the circuit
- O-ring of EVAP canister vent control valve is missing or damaged
- EVAP canister is saturated with water
- EVAP control system pressure sensor
- Absolute pressure sensor

Possible solution
- Loose fuel filler cap
- Leaking fuel filler cap


Hope helps (remember to rate this answer).

Jan 05, 2011 | 2000 Hyundai Sonata

1 Answer

I had an emission test done on my 98 bonneville and it failed because code P0440 evap control system what should i do ?


Here's list why your car is coming up with this code. It could be any of these things causing it.
DTC detecting condition:
  • EVAP control system has a leak.
  • EVAP control system does not operate properly.
Possible cause:
  • Incorrect fuel tank vacuum relief valve
  • Incorrect fuel filler cap used
  • Fuel filler cap remains open or fails to close.
  • Foreign matter caught in fuel filler cap.
  • Leak is in line between intake manifold and EVAP canister purge volume control solenoid valve.
  • Foreign matter caught in EVAP canister vent control valve.
  • EVAP canister or fuel tank leaks
  • EVAP purge line (pipe and rubber tube) leaks
  • EVAP purge line rubber tube bent
  • Blocked or bent rubber tube to EVAP control system pressure sensor
  • Loose or disconnected rubber tube
  • EVAP canister vent control valve and the circuit
  • EVAP canister purge volume control solenoid valve
  • EVAP canister purge volume control solenoid valve and the circuit
  • Absolute pressure sensor
  • Fuel tank temperature sensor
  • O-ring of EVAP canister vent control valve is missing or damaged
  • Water separator
  • EVAP canister is saturated with water
  • EVAP control system pressure sensor
  • Refueling control valve
  • ORVR system leaks
  • Fuel level sensor and the circuit

Apr 01, 2010 | 1998 Pontiac Bonneville

3 Answers

What is a p0440 problem?


Hi there,

Oldsmobile code P0440 refers to: Evaporative Emission System

This means there is a problem with the Evap System, and you will need to inspect the related components:

- Purge Solenoid:

Related Symptoms
  • Stalls after start with a hot engine
  • Poor Fuel economy
  • Emission related faults
- Evap Canistor: Check evap canistor for loose carbon.

- Evap Canistor Vent Valve:

Related Symptoms
  • Poor fuel economy
  • Stalls after start
  • Emissions related failure DTC codes
Hope this helps...

Cheers,

Nov 12, 2009 | 2001 Oldsmobile Alero

Not finding what you are looking for?
1996 Nissan Maxima Logo

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...