Question about 1992 Ford F250

3 Answers

We have no turn signals, hazard flashers, brake lights - fuses ok

We have no turn signals, hazard flashers, brake lights, or instrument lights. we need an electrical schematic with wire color to trouble shoot 1992 F250. If you could send one to my email it is reyount@gmail.com

Posted by on

  • reyount Feb 07, 2010

    I REALIZE THAT THE PROBLEMS ARE INVOLVING TWO DIFFERENT SYSTEMS BUT I WOULD STILL LIKE TO HAVE SCHEMATICS WITH WIRE COLORS. THE HEAD LIGHT SWITCH IS TESTING GOOD SO FAR

  • reyount Feb 08, 2010

    We have voltage at and through the peddle mounted brake switch, but the signal does not make it to the brake lights.

    I have also checked the head light switch and there is power for the panel lights that l is leaving the switch on a Blue with red stripe wire, Does it go directly to the Panel lights, or does it go through a other switch or in-line fuse. I will see if I can locate the in-line fuses under the hood. A schematic with color codes would help and if it would show the "Fire wall feed through connector" that would help also.

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Good day, just sent you a wiring diagram, hope this helps, have a nice day

Posted on Feb 08, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

Have you inspected all fusible links along fender area. Follow cable/wires from battery to that area, and they should be there.

Posted on Feb 07, 2010

  • Mike Butler
    Mike Butler Feb 08, 2010

    I wouldn't rule out a faulty multifunction switch either, as some, or most of them are run through that as well. Have you tried supplying an alternate ground to any, or to dash, or steering column, just to make sure it isn't loss of ground that's causing all this as well?

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

The turn signal switch is the problem,and the headlight switch is the problem for the dash lights.

Posted on Feb 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 02 kia sportage. my signal lights come on but dont blink outside. no lights for the signal lights come on on the dash at all. also, no hazard lights.


If the 15A HAZARD fuse in the passenger compartment fuse box is OK, power is getting to the hazard function of the flasher unit. Pressing the hzard switch should cause the hazard lights to flash. HOWEVER, there is an electronic time and warning indication system module connected to to the hazard switch lead and that may be affecting things. If the 10A TURN fuse is OK, power is applied to the turn switch (with the engine in START or RUN) and you state you can select a right or left turn. HOWEVER, the RED/WHT and RED/BLU outputs from the flasher unit connect directly to the front and rear turn lamps and the instrument cluster turn indicators so you are not getting any flasher output. Again, that electronic time & warning indication system module could be affecting things

Oct 26, 2012 | Cars & Trucks

1 Answer

I have Ford Explorer model 1998 but its indicator lights are not working meanwhile the hazzard lights are working


Your turn signal flasher is separate from the hazard flasher. Replace the turn flasher.

Both the turn signal flasher and the hazard warning flasher are mounted on the fuse panel on the truck. To gain access to the fuse panel, remove the cover from the lower edge of the instrument panel below the steering column. First remove the two fasteners from the lower edge of the cover. Then pull the cover downward until the spring clips disengage from the instrument panel.
The turn signal flasher unit is mounted on the front of the fuse panel, and the hazard warning flasher is mounted on the rear of the fuse panel.

Oct 02, 2010 | 1998 Ford Explorer

1 Answer

1193 plymouth voyager. Brake lighs don't work


Maybe a relay or fuse is bad or the wiring to it.

But you said that the third brake light works.

So the brake switch must be ok.
Turn signals would be the flasher or wiring to it.prev.gif next.gif
CIRCUIT PROTECTION Fuse Block Fig. 1: The fuse box is located under a cover at the lower left instrument panel — 1987 Voyager shown 85616099.jpg
The fuse block and relay bank is located on the driver's side under the lower instrument panel. The fuse block contains fuses for various circuits as well as circuit breakers, horn relay, ignition lamp thermal time delay, and the turn signal flasher. The hazard warning flasher is mounted into a bracket below the fuse block. The individual fuse and relay locations can be found in the wiring diagrams at the end of this section.
is bad.

Aug 01, 2010 | 1993 Plymouth Voyager

3 Answers

I have no brake lights or turn signals on my 95 gmc truck. I have replaced the boards but no luck. Also have checked fuses.


OK if the fuses are good , use a test light and check to be sure you have power at the fuse terminals. you'll check from ground to the terminal on top of the fuse. you should have 12vdc. then , check for power at your brake light switch on both terminals while the brake pedal is pressed, it is located located on the brake pedal assembly. also , check your hazard flasher switch to be sure it is not on. if it was on, check your flashers, both the turn signal and hazard flasher. If everything checks out , your problem is probably in your turn signal switch assembly located in your steering column.

Mar 14, 2010 | 1995 GMC Sierra

2 Answers

No brake lights, turn signals, or 4-ways.


Did you actually check the bulbs? I believe your brake lights, signal lights, hazards all use the same bulb for each side.

Your brake lights may be your brake switch just above your brake pedal.
The signals could be your electronic flasher module (EFM) located under the dash near the steering column.
Your hazards may be affected by the EFM, but not likely and the switch for your hazards may be faulty

Sep 10, 2009 | 1998 Chevrolet Blazer

3 Answers

Hazard flashers do not work. Turn signals do. Changed relay. Nothing. Ugh. 1992 oldsmobile cutlass supreme


You changed the hazard flasher or the turn signal flasher? It has two, one for the hazard and one for the turn signals

Aug 31, 2009 | 1992 Oldsmobile Cutlass Supreme

2 Answers

Location of flasher for turn signal


  1. Access the COMBINATION Turn Signal and Hazard INDICATOR FLASHER on the Left-Hand (drivers) side of the instrument panel in the fuse junction panel.
  1. Remove turn signal flasher/hazard indicator flasher by pulling indicator flasher straight out.
  1. To install, align the terminals of the flasher and press into place.
How about a picture--

388df46.gif

Oct 03, 2008 | 1996 Ford Thunderbird LX

Not finding what you are looking for?
1992 Ford F250 Logo

Related Topics:

397 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...