Question about 2002 Chevrolet Blazer

Open Question

Replace rear axle bearing 2002 chevy blazer - 2002 Chevrolet Blazer

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: rear axle bearing replacement


REAR WHEEL BEARING/ HUB

Removal Procedure

  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Posted on Feb 22, 2009

  • 1 Answer

SOURCE: rear axle bearings need replaceing I hear grinding

Go to Jeep and buy a bearings, seals, and collar. The bearing is held in place on the axle by a keeper collar. This must be cut off to get the old bearing and seal off. Use a wizz wheel to cut it and then whack it with a chisle

To get the axle out. Remove rear diff cover, and wheel and start taking apart. It's not a terrible job, but if you aren't very mechanically inclined, take it to a shop. Make sure you use the correct fluid in the differential.

Posted on Dec 01, 2008

Toyota Guy
  • 42 Answers

SOURCE: rear axle bearings

There are 4 bolts for each rear axle. They are located behind the rear brake drums. Remove e-brake cable from rear drum and take off brake line.(carefully). I recomend draining and changing your rear differential fluid too, because if the fluid by run out of axle housing. also you should replace the seals for the axles of if you are changing the bearings. When you are done don't forget to bleed your brakes, and hooking up e-brake cable. I hope this answers your question.

Posted on Mar 06, 2009

motor1258
  • 6674 Answers

SOURCE: Rear end wine - 2000 Chevy K1500. Sounds like the

First check level of oil in rear end housing, if low, pull drums & see if any axle seals are leaking.
If you want info on doing axle bearings, get back to us.

Posted on Aug 03, 2009

gh20s
  • 343 Answers

SOURCE: 96 chevy blazer rear axle bearing/seal r/r

No. Did you run some emery cloth along the race (bearing surface) to make sure it was smooth and clean? If you leave any part of the old seal or debris on the hub surface, damage the seal when installing it, not liberally packing the bearing with grease or the seal did not seat right you can have issues like yours. Make sure the seal is installed flush and if everything looked good as far as the axle and surfaces, pack more grease in the bearing. When you think there is enough grease in it, put more in. Put the grease in the palm of your hand and with the bearing held flat in the other hand repeatedly tap the bearing on your palm until grease comes out both sides. Then put more on it when you seat it.

Posted on May 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Chevy S10 2wd Rear Axle repair - what do I have to do to remove the carrier bearing?


In general you have to drain the rear end, remove the cover, remove the carrier pin, remove the axles, then remove the carrier from the main shaft and replace the bearings.

Feb 23, 2017 | 2002 Chevrolet S-10

1 Answer

Flat tow or dolly towing for an 2000 S10 Chevy Blazer


If you dolly it you put wear on the wheel bearings and ring and pinion in the differentials on the front or rear depending on what axle you raise.

Mar 14, 2015 | 2000 Chevrolet Blazer

1 Answer

No check/fill plug on my rear axle on my 2001 chevy blazer


Go to You Tube Video & see where the fill plug is

Watch people changing their rear axle fluids on a
2001 blazer

Mar 29, 2014 | 2001 Chevrolet Blazer

1 Answer

What is the rear wheel bearing gear ratio for a 2001 Chevy Blazer 4WD - 2 door?


I think you mean the rear end ratio. there is no gear ratio for the wheel bearing. If you look at the factory sticker on the drivers door, there will be an "axle code". write that down and then look here for the ratio.

http://www.drivetrain.com/parts_catalog/ring_and_pinions/what_gear_ratio_do_i_have_in_my_gm_or_chevrolet.html

Jan 05, 2011 | 2001 Chevrolet Blazer

1 Answer

Needto replace rear wheel bearing 2002 chev s10 blazer


Remove the brake drum, remove the plate that holds the axle to the brake backing plate. The nuts are under the hub flange (where the wheel studs are), there is a hole in this flange to insert a socket on an extension. (you will need to rotate the hub flange to reach all four nuts.) After you get these nuts off, attach an axle puller (slide hammer) to the hub and pop the axle half-shaft out. Take this to a machine shop and have them press the old bearing off and press the new bearing on. Slide the half-shaft back in, and reinstall the nuts.

Might as well replace both bearings (left and right sides) while you are at it. Mark which side the axles come out of, often they are not interchangeable.

Sometimes you can rent or borrow the axle puller from a major chain auto store such as Checker or Auto Zone. They should be able to recommend a machine shop also, if they don't have the correct press.

Oct 04, 2010 | 2002 Chevrolet Blazer

1 Answer

My rearend( I think ) is making a roaring noise and fills like it isn't getting power at times when I use the accelerater


Have the rear-end check out (3rd member) center part of rear-end housing, and your rear axle bearing's, axle bearing if bad can also damage rear axle shaft's and will also have to be replaced.

Jul 09, 2010 | 1999 Chevrolet Blazer

1 Answer

96 chevy blazer rear axle bearing/seal r/r


No. Did you run some emery cloth along the race (bearing surface) to make sure it was smooth and clean? If you leave any part of the old seal or debris on the hub surface, damage the seal when installing it, not liberally packing the bearing with grease or the seal did not seat right you can have issues like yours. Make sure the seal is installed flush and if everything looked good as far as the axle and surfaces, pack more grease in the bearing. When you think there is enough grease in it, put more in. Put the grease in the palm of your hand and with the bearing held flat in the other hand repeatedly tap the bearing on your palm until grease comes out both sides. Then put more on it when you seat it.

May 28, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

How to put wheel bearing on a chevy blazer rear


Pull axle and have auto part store install new bearing

Mar 27, 2010 | 2000 Chevrolet Blazer

1 Answer

Need to remove rear axle to replace bearing


Open the rear diff cover you will see what is holding the axle in place.

Nov 21, 2009 | 2002 GMC Safari

1 Answer

How do I replace the rear wheel bearing in a 2000 chevy blazer


I am sorry to tell you this, but you will have to take the Truck to a Rear End repair shop to do this. If you are very mechanically inclined and have all the specific tools like a slide hammer, bearing puller, bearing installation tool, etc. If you have tools like this, then I would get yourself the car manual. To replace the bearings you will have to remove the axles.

Oct 05, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2002 Chevrolet Blazer Logo

Related Topics:

492 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...