Question about Hyundai Sonata

Open Question

How do I install a cargo net on 2010 sonata

Installation and placement of the cargo net on 2010 sonata

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost4548
  • 776 Answers

SOURCE: need to installation instructions on cargo net for 2008 elantra

Read your Owner's Manual... best solution

Posted on May 31, 2009

MayeresJnot
  • 74 Answers

SOURCE: how to install cargo net where to install last two

Unscrew all the net holders and relocate them further in the oposite direction. When you installed the net, you missed two holes on one side, installing the first screws in the "second" hole, as if you put your shirt on by putting the second button in the third hole. Search for holes on the opposite side of the net, uninstall the first screws and put them into the first hole and re-install each coordinating screws in each hole likewise. Contact you local Ford and Lincoln Mercury Dealer for exact installation hole locations.

Posted on Nov 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the knock sensor located on a 2011 2.4 engine hyundai sonata?


On-Line Service Manual is available on the following website:

http://www.hsguide.net/hyundai_sonata_yf_2011_year_service_manual-6.html

Hyundai Sonata: Knock Sensor (KS). Repair procedures:

Removal
1. Turn the ignition switch OFF and disconnect the battery negative (-) cable. 2. Remove the intake manifold (Refer to "Intake And Exhaust System" in EM group). 3. Disconnect the injector connector (A). 4. Remove the installation bolt (B), and then remove the sensor from the cylinder block. syffl0041n.gif

Installation
caution_icon_eng.gif • Install the component with the specified torques. • Note that internal damage may occur when the component is dropped. If the component has been dropped, inspect before installing. 1. Installation is reverse of removal. Knock sensor installation bolt: 18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)
knock sensor-m3h04eiq4trf45oprzz0vy4e-2-0.jpg

Knock Sensor/Parts are available on the following website:
http://www.partsgeek.com/ymm/2011/hyundai/sonata.html?category=engine_electrical&part=knock_sensor

May 22, 2017 | Hyundai Cars & Trucks

1 Answer

How to install a cargo net on Hyundai Sonata?


One would hope that the dealership would have installed it for you. Beautiful car by the way. They done everything nicely in these cars.

In the instruction manual that comes with the cargo net (Dealer accessory) it will show you how to remove 2 anchor bolts on the left and ride side of the trunk. The carge net should come with the replacement anchor hooks to allow you to hook the elastic straps to both sides to get maximum use of the net.

I would say since your car is as new as it is. Come into the dealer and get them to put it in for you.

Dec 25, 2014 | 2015 Hyundai Sonata

1 Answer

Need a diagram for a serpentine belt for a hyundai sonata 2000 204 engine with a/c.


The link below will take you to a diagram of the serpentine belt placement.

http://www.2carpros.com/diagrams/hyundai/sonata/2000

Aug 30, 2011 | 2000 Hyundai Sonata

1 Answer

How to install cargo net where to install last two plastic screw net holders


Unscrew all the net holders and relocate them further in the oposite direction. When you installed the net, you missed two holes on one side, installing the first screws in the "second" hole, as if you put your shirt on by putting the second button in the third hole. Search for holes on the opposite side of the net, uninstall the first screws and put them into the first hole and re-install each coordinating screws in each hole likewise. Contact you local Ford and Lincoln Mercury Dealer for exact installation hole locations.

Nov 15, 2010 | 2005 Lincoln LS

1 Answer

What do I need to unscrew in the trunk to change the reverse light in my 01 chevy impala


Tail Lamp Assembly Removal & Installation To Remove:
  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.
  8. Remove the side marker lamp socket by turning counterclockwise.
To Install:
  1. Install the side marker lamp socket by turning clockwise.
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
prev.gif next.gif

Oct 18, 2010 | 2001 Chevrolet Impala

2 Answers

Left rear turn signal bulb is burned out.


Tail Lamp Assembly
Removal & Installation
To Remove:

  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.

  1. To Install:
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
      Please don't forget to rate !!!!!!

    Mar 28, 2009 | 2002 Buick Century

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    71 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7710 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...