Question about Jaguar XJ8

1 Answer

Try to start engine and enginesafe shutdown mode flashes on dash

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Check oil

Posted on Feb 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mechanics advised that gearbox needs replace after diagnostic Of codes . Dash light still on after codes being read , have had ecu replaced 2yrs ago ? What do you think it could be , thanks phil


didnt specify vehicle --generic answer--until repair is made the vehicle will show engine light and have codes --if gearbox is problem for limp mode /until repairs are made or gearbox replaced you will be in limp mode --and as to sensor find out what one it was --start problem may show back up if sensor was problem --and GET a 3rd opinion you have 2 mechanics with different opinions on your problem and i guess they are reading your trouble codes differently

Sep 20, 2016 | Cars & Trucks

1 Answer

A 2003 4-door Dodge Neon. With the heater on in the recirculate setting all dash lights flash on, car dies, all lights go out. Full tank of gas, good battery, alternator operating, no broken belts.


Your ASD automatic shutdown relay is triped do to a electric problem. Does it happens when you run heater on but not in recirculating mode if not it is either the switch or in recirculating system. If problem happen with heater just turned on you need to replace ?ontrol unit

Dec 27, 2015 | Cars & Trucks

1 Answer

Where is the computer test port on a 1995 isuzu rodeo


This is straight from Haynes Repair Manual for 1989-1997 Isuzu Amigo/Rodeo/Honda Passport (book # 47017:
The 12 pin Assembly Line Data Link (ALDAL) terminal is located under the dash on the driver's side on 3.1L engines. To retrieve the trouble codes, connect a jumper wire to terminals A and B. It may be covered with a plastic cover. They suggest using a paper clip to jumper the two terminals-then turn ignition switch to ON position (NOT ENGINE START). Check engine light on dash will flash-one flash-a pause-then two short flashes-indicating code 12-diagnostic mode. After self checking-if there are any trouble codes-the light will flash proper codes using mentioned method.Note the flash code then call a shop with your info for what ails your Rodeo.

Mar 31, 2010 | 1995 Isuzu Rodeo

1 Answer

1998 dodge caravan shutdown while driving flashing lights on dash .car wont start


When activate the shutdown sistem in Dodge, the power line of ECU is of, but the power line is generated from the ECU to all the control sistem, including the Transmition control module. That is the reason of the car don't start. The line of 12 volts of the injectors, and ignition coil is in the of moment, and when the temperature of the board of the ECU is down, it start again. Here in Chile, I repair the ECU, but in other countrys, you can buy an other new.
Good Luck.

Dec 21, 2009 | 1998 Dodge Caravan

1 Answer

MY 2000 XJ8 AFTER RUNNING FOR A WHILE, DASH BOARDLIGHTS GO CRAZY.


the ecu is damaged. take it to the dealer. you MUST be very careful when jumping these vehicles.

Nov 04, 2009 | Jaguar Xj Series Cars & Trucks

2 Answers

How do I reset my oil light on my 2004 Buick Rendezvous?


Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three time in five seconds. If the CHANGE OIL SOON’ indicator flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHANGE OIL SOON indicator comes on and stays on for five seconds, repeat the procedure.

Sep 07, 2009 | 2004 Buick Rendezvous

1 Answer

Lights on dash, drive,park, reverse, etc flash after starting car


check the transmision codes with obd1 tranny in safe mode. check droping resistor. Vitally

May 22, 2009 | 1995 Honda Accord

1 Answer

Check light is showing on my dash board,it comes off and on


I think when it starts flashing the car is in "limp home mode" which indicates there is a problem and limits the engine to minimise damage. Best get it to a garage and get it plugged into diognostics equipment.

Mar 04, 2009 | 2001 Audi A6

2 Answers

IDLE TIMER FOR 2008 F550


refer thge owner's manual of 450, u'll get these kinda details there.

Feb 27, 2009 | 2008 Ford F 450 Super Duty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...