Question about 1993 Chevrolet Lumina

1 Answer

After the serpitine belt tensioner was replaced we are not getting any gas. We have checked the relay for power and the main connector power at the tank only getting .3vdc at any of the hot pins during the ignition switch to on and a short jog of the engine. Were not sure the pump is bad. did however get 12volts at the relay and chked crank sensor no mechanical damage noted pretty sure this is a non issue.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 58 Answers

Check the oil pressure sender/switch it controls the fuel pump Mabey the connector came off

Posted on Feb 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How To Put On Serpitine Belt For Alternator


place large ratchet on gray tensioner and pull it until tension releases from belt

Jul 15, 2012 | 1993 Plymouth Voyager

3 Answers

My girlfriend stuck out in mountains with broken fan belt . she picked up a belt but doesent know if she has the right one or how to put it on few tools and some help is available how do you replace it?


IT SHOULD BE SERPITINE BELT . SHOULD HAVE A TENSIONER PUT BELT AROUND PULLEYS THEN PULL UP ON TENSIONER TO GET BELT ON . JUST A WRENCH OR SOCKET TO FIT TENSIONER MAY BE A 15,17 MM.MAYBE UNDER HOOD A DIAGRAM HOW BELT GOES

Dec 26, 2010 | 2006 Dodge Ram 3500 Truck

2 Answers

I can't get my serpentine belt back on after changing my alternator. What do I do now?


Hi Friend:

#1) On your vehicle you have a Serpitine Belt tensioner ,your Serpitine Belt runs on this also;

#2) Locate your Belt Tensioner its (Aluminum) and is Spring Loaded to kep your Belt at the Proper Tension.

#3) On the front side of the Tensioner there is a Bolt Head, Get a Breaker Bar ,Correct size Socket or(Ratchet and Socket)

#4) With the tool on the bolt head the Tensioner will move by applying pressure to the Tension.It will only move 1-Way when applying Pressure with Your Tool.

#5) By Moving the Tensioner you will be getting enough Slack that you Can Put the Belt Back on.

#6) You should have a Belt Routing Diagram on your Cooling Fan Shruod or the Frame in Front of it.

#7) Just take a Good look at how the Belt HAS to Be Routed it will only work 1-Way.

#8) So Follow the Diagram for Routing and you should have no Problems. Don't Forget it Will not Go on Correctly until you Apply perssure to your Belt Tensioner.

Please let me Know how well i have Assited you.By voting .And a Testamony would be Appreciated.

Thanks for Using FIXYA from; d_hubbs

Jun 18, 2010 | 1991 Chevrolet Cavalier

1 Answer

Replacing serpitine belt tension pulley ? Is the center bolt left handed threads or right handed? What size is the head on that bolt?


Lefty Loosey, Righty Tighty. As you look at the bolt from the front of the engine. It should loosen when turned counter clockwise. Curios though, why are you removing and replacing the tensioner? If your having trouble with belt tension it is most likely the belt.

Jun 25, 2010 | 1993 Mercury Cougar

2 Answers

Tighten serpitine belt


if your belts loose it probably needs replacing.theres a tensioner pulley on those that automatically tighten as it stretches.unless your tensioner pulleyis getting weak which does happen

Nov 23, 2009 | 1993 Dodge Stealth

1 Answer

How do I get the tension off the serpitine belt to remove


on the bottom there is a tension pully u can adjust it from there

Jul 09, 2009 | 1997 Buick Skylark

1 Answer

Belts sqeeling on cold start up.


check your tensioner pulley and idler pulley by removing serpitine belt spin the pulleys inspect for roughness and endplay all so check harmonic vibration dampner pulley the one at crankshaft for seperation/endplay the rubber cracs and pulley walks on startup you could draw a metal file across the inner face of serpitine belt this will remove glazing or replace belt may be even better

Nov 30, 2008 | 2005 Pontiac GTO

1 Answer

How to change the serpitine belt


you most release the tension pully to take the belt off

Nov 15, 2008 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
1993 Chevrolet Lumina Logo

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...