Question about 2002 Ford F350 Super Duty DRW Reg. Cab

1 Answer

I have a mondeo 2.0 tdci 02,the glow plug light came on when i was driving and stalled,so i changed the camshaft censor and the car was fine,then a couple of days later,i went to start the car and the battery was flat,bought a new battery and was fine,then on motorway the glow plug light came on again and stalled,re-started the car and drove off,then started to loose power and ignition lights came on and car stalled,now it will not start at all????

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 3,187 Answers

That is limp mode there is a problem with the engine and you need a code reader to find the problem cam and crank sensors are prom to go over time but there are other sensors and to find the right problem the codes need reading. also i would recommend you check the diesel round seal on the intake as these can fail. ford want you to by a new unit and so do others, but the seal can be replaced and only cost a few pence. take old one into a bearing and seal supplier and they will locate one in stock, has this problem myself as it cause engine problems with weak fuel pressure.

Posted on Jun 23, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: mondeo tdci

hi there, you will need a diagnostic check carried out to locate the exact fault, most garages have the equipment to carry out these checks so you won't need to visit your ford agent, a common fault on the engines is the camshaft sensor these cost around £20 and are very easy to replace, however once you have it tested you will now your exact fault, hope this helps

Posted on Oct 24, 2008

alicantecoli
  • 22114 Answers

SOURCE: FORD MONDEO 130 TDCI CUT OUT AND WONT START

common rail injection or traditional injector pump

Posted on Nov 11, 2008

alicantecoli
  • 22114 Answers

SOURCE: fod mondeo cut out

ford only on the newer models ,software readers like scansoft or digisoft will not touch it if its a europeon model ,dont know about cars sold in america weither its the same coded software or not

Posted on Nov 17, 2008

MrScary66613
  • 1990 Answers

SOURCE: will a 2003 mondeo tdci engine fit into a 2002 mondeo tdci

They should be. The SVT Models stay Very Consistent on the Motors.

Posted on Jan 21, 2009

  • 184 Answers

SOURCE: mondeo clutch problem

yes it will fit.

Posted on Mar 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford mondeo faults


the flashing orange light is the glowplug light that telling you there is a engine managment problem. you need to get the fault code out of the engine control module with a obd code reader to determine the cause but the common cause of the flashing glow plug warning is a air leak after the turbo charger

Jun 04, 2017 | 2006 Ford Mondeo 1.8

2 Answers

I have a mondeo 53 plate 2.0 tdci that has a lack of power and running lumpy


I would be checking spark plugs and plug leads. Also could be petrol injectors, sorry about so much but this could be many things. Billy

Jun 05, 2014 | 2003 Ford Mondeo

1 Answer

Misfire po300


Error Code: P0300
Description:
Random/Multiple Cylinder(s) - Misfire Detected
Problem Area:
Air Intake System leaking.
Fuel Supply faulty.
Injector(s) faulty.
Ignition Cable(s) and/or Spark Plug(s) faulty.
Ignition coil(s).Exhaust Gas Recirculation (EGR) Valve stuck/open.
Camshaft Position Sensor faulty.
Low compression.
Wiring.

Solutions:
Check Misfire Recognition.
Check Air Intake System.
Check Fuel Supply.
Check Injector(s) and Injector Sealing.
Check Ignition Cable(s) and Spark Plug(s).
Check Ignition Coil(s).
Check Exhaust Gas Recirculation (EGR) Valve .
Check Camshaft Position Sensor.

Feb 25, 2014 | Chevrolet Cobalt Cars & Trucks

1 Answer

Glow plug replacement in a mk4 mondeo


This may help

http://www.talkford.com/community/topic/211008-glow-plugs-replacement-mk4-18-tdci/

Dec 31, 2013 | 2008 Ford Mondeo 2.0

1 Answer

Need cam timing spec for mondeo st220


For camshaft timing spec,click the link below :----Ford Mondeo ST220 camshaft Timing specifications? http://technoanswers.blogspot.in/2012/02/ford-mondeo-st220-camshaft-timing.html
-------This will help.
Also check this related help links:---

How test cam shaft? Testing Car Camshaft? http://repairhelpcenter.blogspot.in/2012/02/how-test-cam-shafttesting-car-camshaft.html
----------How to Inspect Camshaft? http://repairhelpcenter.blogspot.in/2012/02/how-to-inspect-camshaft.html
------------Crankshaft and camshafts timing marks? http://technoanswers.blogspot.in/2012/02/crankshaft-and-camshafts-timing-marks.html
----------Camshaft, Bearings & Lifters Replacing ? http://howtobyme.blogspot.com/2011/12/camshaft-bearings-lifters-replacing-on.html
---------Camshaft Position (CMP) Sensor replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-camshaft-position-cmp-sensor.html
------------How to replace Camshaft? Replacing Vehicles Cam Shaft Assembly? http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-camshaft-replacing.html
---------This will help too.Thanks.

Feb 13, 2012 | Cars & Trucks

3 Answers

Ford focus 1.8 tdci MY 2003 terrible cold start


only takes one glow plug out of order to cause problems . check them for proper volatge and resistance

Mar 30, 2010 | 2003 Ford Focus

1 Answer

Will a 2003 mondeo tdci engine fit into a 2002 mondeo tdci


They should be. The SVT Models stay Very Consistent on the Motors.

Jan 21, 2009 | 2002 Ford SVT Focus

1 Answer

FORD MONDEO 130 TDCI CUT OUT AND WONT START


common rail injection or traditional injector pump

Nov 11, 2008 | 2000 Ford Focus

1 Answer

Fod mondeo cut out


ford only on the newer models ,software readers like scansoft or digisoft will not touch it if its a europeon model ,dont know about cars sold in america weither its the same coded software or not

Nov 11, 2008 | 2000 Ford Focus

1 Answer

Mondeo tdci


hi there, you will need a diagnostic check carried out to locate the exact fault, most garages have the equipment to carry out these checks so you won't need to visit your ford agent, a common fault on the engines is the camshaft sensor these cost around £20 and are very easy to replace, however once you have it tested you will now your exact fault, hope this helps

Oct 23, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2002 Ford F350 Super Duty DRW Reg. Cab Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...