Question about 1991 Chevrolet K2500

1 Answer

When in reverse the trany shutters slightly. Is it serious?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Definately something to worry about:
torque converter, trans filter, U-joint(s), or your rear gears r going out

Posted on Aug 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is color of reverse wire on 2003 ram steering coloum


There should be no wires up there for the reverse of the trany just a cable and the switch on the trany controlls all the switching for the trany. It is called the nuetral saftwy switch mounted on the drivers side of the trany with a cable that moves it in and out of gear.

May 04, 2014 | 2004 Dodge Ram 1500

1 Answer

2000 blazer won't go into reverse. Loud whining noise.


This may be due to a bad pump, but first check the trany oil, with the engine running and warm check the level of trany oil in the trany, if its low that would be your problem but if full then i would say its time for a trany rebuild, hope this helps.

Nov 28, 2010 | Chevrolet Blazer Cars & Trucks

2 Answers

Reverse Gear does not work, Can this be repaired ? or replaced? So I do not use reverse.


This is very common, the reverse gears blows out, the reverse gear and some bushings need replacing, many trany shops wont do it, they rather sell you another trany, we had a retired vw tech that would repair them for us all you did was remove the trany, but anyway it can be repaired the parts cost about 150.00 then the rest is labor,

Sep 18, 2010 | 2003 Volkswagen Jetta TDI

1 Answer

My 2003 Pontiac Wont go in reverse when u put it in reverse...What could the problem be and How much can I estimate spending to fix it


This problem can be caused by two things low trany fluid or worn trany, warm engine and put car on level ground and check trany oil level, if the oil level is good then you may need a rebuild, this kinda job could run about $1,800.00 to $2,500.00 depending on where you live and what trany shop you go to. hope this is helpful.

Sep 13, 2010 | 2002 Pontiac Grand Am

1 Answer

1994 magna 2.6 L engine shutters slightly when idling in drive but ok when in park or reverse


Possibly when the radiator fan kicks on it robs a little power from the engine causing it to shutter a little.When the engine is in park the RPM is higher thus when the fan comes on it doesnt cause much of a load on the engine.Just open the hood as someone starts the car,puts it in park and feel for the fan to come on and see if it's causing the engine to shutter

Oct 23, 2009 | 1994 Mitsubishi Diamante

1 Answer

Trannie, no drive no od,no 2 will go in r low 1


if you drove it too far too fast in 4 wheel low. you could have done some serious damage to the trani. i have the same truck in a 1998 and the tachomiter goes nuts at 15 mph in 4 low. it was never meant to drive for any distance in 4 low. if your lucky. when your rearend went it didn't take out your drive shaft. if your not lucky. your drive shaft took some punishment and in turn damaged the trani.

Oct 07, 2009 | 1991 Chevrolet C1500

1 Answer

I only have reverse in my 1997 toyota camry i need


It might not be the pump.. If it works in reverse - the pump should be working.. There could be damage to the bands.. It also could be the modulator or electronic components inside the trani..

If you have not done trani work befor - I would avise taking it to a trani shop for diognosis.. Allot of them will give a free estimate..

Sep 23, 2009 | 1997 Toyota Camry

1 Answer

2000 ford ranger pulls in reverse but not in drive, whats the problem?


When you say "pull" I assume you mean it wont go foward..
1st thing -check the trani fluid while the engine is running in park..
The tranies in these trucks are known to give out.. Reverse is usually run on the 3rd gear band.. It could mean that the band for 1st gear is damaged.. Could also be a vacume & or modulator issue.. Some trani shops give free estimates..

Jul 08, 2009 | 2000 Ford Ranger SuperCab

1 Answer

2002 Sunfire No Reverse


the reverse is the first thing to go out in your transmition. Check trani fluid while car is hot and idling in park on level surface if needed add trani fluid. If problem persists sometimes replacing the transmision screen may enable the reverse usually and new trani is needed.

Nov 14, 2008 | 1997 Pontiac Sunfire

Not finding what you are looking for?
1991 Chevrolet K2500 Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...