Question about 2000 Dodge Caravan

1 Answer

How much is pads/oil pan and powe belts and trans mount

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 204 Answers

30-40 for the pads; 125-175 for pan; 40 belts; and 40-50 for mounts depends on where you shop.

Posted on Feb 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace motor mounts on a 1989 Honda Accord LXi 2dr? Am I suppose to support the engine with a jack by the oil pan and if so, should I put a piece of wood between the jack and the oil pan to not...


You got it
Wood under oil pan
May need a long pry bar also
Just don't pry on any aluminium items,trans case
& such.
Do all motor & trans axle mounts & be done with
not having to come back there ever again
Support the car with jack stands & be careful when
raising the engine some, that the sub frame stays
on the jack stands & only the motor moves just
enough to get the mounts out.

Jul 19, 2013 | Cars & Trucks

1 Answer

Oil Pan Removal


Disconnect the exhaust pipes, take the load of the mount bolts with a jack under the pan and remove the engine mounts, then remove the oil pan bolts and carefully raise the engine as high as you can off the mount pads, pry the Pan loose and reverse to put back together.

Feb 24, 2012 | 1994 Nissan Pickup

1 Answer

Have a oil leak on oil pan on my f350,got the oil pan lose,but cant get the oil pan out, trans is in the way, do i loosen the trans or motor mount on engine


Remove the motor mount bolts and raise the engine slowly. Don't dent the oil pan when raising the engine! After the engine is raised, you should have enough clearance to remove the pan.

Apr 06, 2011 | 1979 Ford F 350

1 Answer

Is there any way to replace the serpentine belt on a 97 oldsmobile achieva without removing the engine mount


If its the 3.1 liter with the upper engine mount on the passenger side of the motor than no. You will need to remove the mount.

The good news is is its not that hard to do. Place a jack under the oil pan with a block of would between the jack and the oil pan and the trans pan as far to the passenger side as you can and still be able to touch both pans with the block of wood.

Jack up the motor just enough so that it just start to push up on the motor mount. Remove the bolts that hold it to the bracket on the engine. Remove the retainer for the cruise, if equipped, unplug the cruise and set aside. Remove the nut from the mount on top and the two bolts from inner fender.

Jack up the motor just enough to remove the mount.

You'll then be able to replace the belt.

Dec 15, 2010 | Oldsmobile Achieva Cars & Trucks

1 Answer

How do u replace belt on 1996 buick rivera


REMOVE THE MOTOR MOUNT. MAKE SURE YOU HAVE A JACK AND A N OLD YELLOW OR WHITE PAGES. PLACE THE BOOK ON TOP OF THE JACK. PUT THAT UNDER THE OIL PAN. JACK THE JACK UP TILL IT MEETS UP WITH THE OIL PAN. YOU WONT TO USE SOMETHING SOFT BUT STRONG. THE OIL PAN IS MADE OF VERY VERY THIN ALUMINUM SO BE CAREFUL NOT TO CRUSH IT. NOW THAT THE JACK IS SNUG UNDER THE OIL PAND YOU CAN REMOVE THE MOTOR MOUNT . THEN REMOVE THE BELT. TAKE NOTE OF HOW THE BELT WRAPS THRU THE MOTOR MOUNT. I LIKE TO DRAW OUT A PIC OF IT SO I WILL NOT FORGET.
TO REMOVE THE BELT TAKE A 15MM WRENCH AND RELEASE TENSION OFF THE TENSIONER. WATCH YOUR FINGERS BECAUSE IF IT SLIPS YOU WILL BE SCREAMING YOUR **** OFF IN PAIN

Oct 17, 2010 | 1996 Buick Riviera

1 Answer

Where is the top oil pan located in the 2003 nissan altima 3.5? Need a diagram. This car has 2 oil pans.


Aluminum (upper) oil pan bolt loosening sequence—3.5L engine



dac3faf.gif

Position a suitable jack under the transaxle.
  • Crankshaft Position (CKP) sensors (REFERENCE and POSITION) from the oil pan
  • Front and rear engine mounting nuts and bolts
  • Center crossmember assembly
  • Engine drive belts
  • A/C compressor and mounting bracket
  • Rear cover plate and the lower transaxle bolts
  • Aluminum (upper) oil pan bolts in the reverse of the installation sequence

May 23, 2010 | 2003 Nissan Altima

1 Answer

1999 buick park avenue ultra motor mount and supercharger belt replacement


  1. Remove the engine mount to engine mount bracket nuts. Important: Ensure that the wood block extends past the width of the oil pan in order to avoid damage.
  2. Use a jack with a block of wood on the jack under the oil pan in order to support the engine.
  3. Remove the engine mount bracket front upper and lower nuts.
  4. Remove the engine mount bracket front upper and lower studs and spacer.
  5. Lower the engine as necessary and rotate the tensioner to remove the drive belt.Remove the supercharger belt.
  6. Reverse For INSTALATION

Dec 09, 2009 | 1999 Buick Park Avenue

3 Answers

The car is leaking oil and the mechanic said it was because there is a whole in the oil pan and it will cost 1800 to fix. can i buy another oil pan and put it on myself?


OIL PAN
REMOVAL
Drain engine oil.
Remove front engine mount bracket.
Remove power-train bending strut.
Remove structural collar from oil pan to trans-axle Structural Collar - Removal and Installation
Remove trans-axle lower dust cover.
If equipped with air conditioning, remove oil filter and adapter.
Remove oil pan.
Clean oil pan and all gasket surfaces.
INSTALLATION
Apply Mopar® Silicone Rubber Adhesive Sealant or equivalent at the oil pump to engine block parting line Oil Pan Sealing
Install a new oil pan gasket to pan.
Install pan and tighten screws to 12 N·m (105 in. lbs.)
Install oil filter and adapter.
Install trans-axle lower dust cover.
Install power-train bending strut.
Install front engine mount and bracket
CAUTION: The torque procedure for the structural collar must be followed, as damage to oil pan or collar could occur.

Install the structural collar Structural Collar - Removal and Installation using the following 3 step torque sequence:
Step 1: Install the collar to oil pan bolts and tighten to 3 N·m (30 in. lbs.)
Step 2: Install collar to trans-axle bolts and tighten to 108 N·m (80 ft. lbs.)
Step 3: Final torque the collar to oil pan bolts to 54 N·m (40 ft. lbs.)
Fill engine crankcase with proper oil to correct level.

Auto Zone carries the Oil pan you need for around $75.00 and they will have the step by step instructions for you to replace the oil pan. will take just over 2 hours for the average person. Good luck and keep me posted.

Nov 30, 2009 | 2002 Dodge Neon

1 Answer

Need to change oil pan


e
Cavalier, Sunfire 2001-2005

Oil Pan - Removal & Installation

2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Right front wheel Right inner fender splash shield Starter motor and bracket Engine mount strut bracket Oil pan
To install:


672c0b8.jpg

Fig. Exploded view of the oil pan mounting and related components-2.2L (VIN 4) engine
  1. Place a 2mm bead of RTV sealer to the oil pan sealing surface except at the rear seal mounting surface. Using a new oil pan rear seal, apply a thin coat of RTV sealer on the end down to the ears.
  2. Install or connect the following:
    Oil pan with a new gasket. Torque the nuts and bolts to 89 inch lbs. (10 Nm). Engine mount strut bracket. Torque the bolts to 49 ft. lbs. (66 Nm). Starter motor and bracket. Torque the bolts to 37 ft. lbs. (50 Nm). Right fender splash shield Right front wheel. Torque the nuts to 100 ft. lbs. (140 Nm). Negative battery cable
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.
2.2L (VIN F) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine mount strut bracket Drive belt Lower then upper AC compressor bolts Oil pan bolts Oil pan

    1c9e9c9.jpg

    Fig. Remove/Install the oil pan bolts in this sequence-2.2L (VIN F) engine
To install:
  1. Apply a 2 mm bead of RTV sealant around the perimeter of the oil pan and the oil suction port opening. Do not over apply the RTV. More than a 2 mm bead is not required.
  2. Install or connect the following:
    Oil pan and tighten the bolts to 18 ft. lbs. (25 Nm) AC compressor bolts Engine mount bracket Drive belt
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.

2.4L Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Flywheel/converter cover Right wheel Right wheel well splash shield Accessory drive belt Air conditioning compressor lower bolts Transmission-to-engine brace Engine mount strut bracket Radiator outlet pipe bolts Radiator outlet pipe from the oil pan Oil pan to the flywheel cover bolt and nut Flywheel cover stud for clearance Radiator outlet pipe from the lower radiator hose and oil pan Oil level sensor connector Oil pan
To install:
  1. Inspect the oil pan gasket; it is reusable if not damaged.
  2. Install or connect the following:
    Oil pan with the gasket. Torque the M8 bolts to 18 ft. lbs. (24 Nm) and the M6 bolts to 106 inch lbs. (12 Nm).

    2ffc5e9.jpg

    Fig. Oil pan fastener torque specifications-2.4L engine
    Oil pan to the transmission nut Oil level sensor connector Radiator outlet pipe to the lower radiator hose and oil pan Exhaust manifold brace Radiator outlet pipe. Torque the bolts to 124 inch lbs. (14 Nm). Engine mount strut bracket. Torque the bolts to 55 ft. lbs. (75 Nm). Transmission to the engine brace Air conditioning compressor lower bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Accessory drive belt Right splash shield Right front wheel Flywheel/converter cover Negative battery cable
  3. Refill the crankcase.
  4. Refill the cooling system.
  5. Start the vehicle and verify no leaks.

Hope helped (remember rated this help). Good luck.

Oct 22, 2009 | 2001 Chevrolet Cavalier

1 Answer

How can i get the oil pan out on a 2001 chevy malibu?


2.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan


  1. Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm).
  2. Accessory drive belt
  3. Negative battery cable

  4. Fill the engine with oil to the correct level.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan

To install:
  1. Apply a 0.13 inch (3.5mm) bead of the GM P/N 12378521 sealant around the perimeter of the oil pan and oil suction port opening.
  2. Install or connect the following:

    Oil pan. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).

    0900c1528024bb26.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Oil pan bolt sequence-2.2L engine
    Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm). Accessory drive belt Negative battery cable
  3. Fill the engine with oil to the correct level.
3.1L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Evacuate and recover the A/C system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    WARNING DO NOT disconnect the refrigerant lines or allow the compressor to hang unsupported.


    Negative battery cable Accessory drive belt Upper and lower radiator hoses Right front wheel Inner fender splash shield Antilock Brake System (ABS) Wheel Speed Sensor (WSS) electrical connector Right front ball joint from the steering knuckle Right side outer tie rod end A/C compressor bolts and move the compressor aside


    Evaporator-to-accumulator A/C line Flywheel cover Engine cradle bolts Crankshaft balancer Starter motor Oil pan

To install:

0900c1528024bb27.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the oil pan mounting-3.1L and 3.5L engines

  1. Install or connect the following:

Sep 02, 2009 | 2001 Chevrolet Malibu

Not finding what you are looking for?
2000 Dodge Caravan Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...