Question about 2002 Chevrolet Blazer

1 Answer

How many grease fitting are on a 2002 chev blazer, 4 wheel drive ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Will very. Alot of the parts on the new cars are sealed and wont have grease fittings but when parts of steering and suspension are replaced then the have grease fitting so honestly it can very from car to car.

Posted on Feb 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4 wheel drive on 2001 chev blazer won't kick in..lights flash, hear sound under floor board as if something moved/slid but won't go into 4 wheel


It sounds like the motor for engaging the 4wd isn't completely engaging, you're going to have to crawl under the truck and watch it while someone engages it. I cannot express enough how dangerous this could be to the person who climbs under the vehicle, take every precaution necessary even as far as lifting the truck up on jack stands on all 4 corners with all wheels off the ground.

Oct 25, 2016 | Cars & Trucks

1 Answer

2000 BLAZER SQUEAKS OVER BUMPS AND WHEN TURNING REAL BAD


I had the same problem with my 01 suburban. It was the struts. Replaced them and no more squeaks!!

Mar 16, 2009 | 2000 Chevrolet Blazer

1 Answer

Grease fittings front end


certain durangos, have the fittings on the ends of the tie rods, and the ball joints, but it is different for 2 wheel drive and 4 wheel drive models... if you do not see the grease fittings on the ball joints, or the tie rods that means they can not be greased... check the boots on them tho, if there is any tearing, or the boot is missing or broken in any way, that part will need to be taken out and replaced...if the suspension part has no grease fitting in place, this indicates it is sealed and doesn't require periodic lubrication

Mar 14, 2009 | 2000 Dodge Durango

3 Answers

My truck is stuck in 4 lo


pull atc 25 amp fuse in underhood fuse center and 10 amp 4wd fuse inside cars fuse box,your problem is in control box behind kick panel on pass. side ,corrosion build up,

Mar 06, 2009 | 2000 Chevrolet Blazer

1 Answer

4 wheel drive not working


Vacume lines or vacume switch on transfer case,or vacume pod to front axle.

Jan 05, 2009 | 1993 Chevrolet S-10 Blazer

1 Answer

4 Wheel drive not engaging.


After finding a vacuum line that was off from the auto body shop that never was reconnected , after they removed it when they replaced the left side fender from a crash. Reconnected it and now it works. It was hard to find. Due to it is located below some other componets and wires.

Dec 26, 2008 | 2001 Chevrolet Blazer

2 Answers

1999 chev blazer 4x4 system


I have a 1999 chevy blazer that stuck in 4 wheel drive. How do you get it out.

Nov 23, 2008 | 1999 Chevrolet Blazer

1 Answer

1998 Chev S10 Blazer Transfer Case not shifting into 4x4


Does the 4 hi light blink when you try to put it in 4 wheel drive? My did that and it was the module.

Nov 17, 2008 | 1998 Chevrolet Blazer

2 Answers

1999 Chev Blazer 6cyl 4.3L 4WD Rear Brake assy - I have replaced 2 Brake Pads and Rotor. After replacing and a test drive... Its making a scrapeing noise and now the rotor is extreamly hot and descolored....


I replaced the rotors and pads on my right hand drive Blazer and had the same problem ,dont worry in a couple of days normal running the pressure goes away and you dont get the heat problem.
Its just the new pads bedding in.

J.C.
U.K.

Jul 17, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2002 Chevrolet Blazer Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...