Question about 2002 Chevrolet TrailBlazer

1 Answer

2002 chevy blazer. Trying to swap out the water

Trying to swap out the water pump and can't figure out how to get the fan shroud off. And I can't get the water pump out w/o removing the fan shroud. How do I remove the fan shroud? Thanks-Jonas

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 102 Answers

The new chevys are a pain. There should be alot of little nuts on the top of the shroud possibly under a small piece of weather stripping. There should also be 2 or 4 small bolts halfway down the shroud on both sides. Then there are 2 or 4 bolts on the bottom of the shroud. It should end up in two pieces with one piece coming out the top and one out the bottom. Removing the shroud most of the time is not necessary but it helps.

Posted on Feb 03, 2010

  • shawn_mic413
    shawn_mic413 Dec 29, 2012

    I am having problems removing the shroud on my 2005 trailblazer

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace water pump on 4.2 liter 2004 trail blazer LS


4 bolts hold the shroud on. 2 on bottom,2 on top. Leave on in on the top until you remove the clutch fan. Clutch fans are a pain to get off with out the right tools. Once off, remove the bolt from the shroud and pull them out together. Remove the serpentine belt. Remove the pump.

Dec 16, 2015 | 2004 Chevrolet TrailBlazer

2 Answers

I need step by step instructions on how to replace a water pump on a 2002 Chevy Trailblazer LT


Go to www.trailvoy.com and do a search on "how to replace water pump". You will find a thread with a procedure and pictures for the work required.

Sep 30, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

I need to replace teh water pump on my 2002 chevy blazer. What is the easiest way of doing it? It looks like i need to disassemble the fan to get to it. Is there a way to work around that?


Forget easy. Easy, is when you have room to work on the water pump. Remove all things necessary to do the job. Take your time.
Good time to replace belts and free up alt,power steering,vac pump,etc,bolts and get them moving freely. Don't try to do less.Do more, and save time in the future,when your in there for something else.

Sep 29, 2010 | 2002 Chevrolet Blazer

1 Answer

I'm looking for torque specs on the water pump bolts to the block for 2000 chevy blazer 4.3 L


Fig. Exploded view of the water pump assembly mounting-4.3L engine

fdf58a9.jpg

To install:
  1. Clean the gasket mounting surfaces.
    NOTE The water pumps on some of the engines covered may have been installed using sealer only, no gasket, at the factory. If a gasket is supplied with the replacement part, it should be used. Otherwise, a 1 / 8 in. (3mm) bead of RTV sealer should be used around the sealing surface of the pump.
  2. Apply sealant to the water pump retainer threads.
  3. Install or connect the following:

    Water pump using a new gasket. Tighten the water pump retainers to 89 inch lbs. (10 Nm) for 4.2L engines, or to 30 ft. lbs. (41 Nm) for 4.3L engines. For 5.3L engines, tighten the bolts to 11 ft. lbs. (15 Nm), then to 22 ft. lbs. (30 Nm). Coolant hose(s) Water pump pulley. Tighten the pulley bolts to 18 ft. lbs. (25 Nm). Fan or fan and clutch assembly Serpentine drive belt (if equipped) by positioning the belt over the pulleys and carefully allow the tensioner back into contact with the belt. V-belts (if equipped) and adjust the tension Upper fan shroud Negative battery cable
  4. Refill the engine cooling system.
  5. Run the engine and check for leaks.

Hope this help to solve it; rebember rated this post. Good luck.

May 01, 2010 | 2000 Chevrolet Blazer

1 Answer

I need to change out a water pump on my 92 full size blazer.


u might be able to just remove alt and fan and maybe not. Only other things that might needed to removed is a/c compresser, power steering pump and fan shroud (((you dont have to remove shroud but makes it alot easier)))

look at water pump and look to see what all in way of getting to all the bolts

Apr 07, 2010 | 1992 Chevrolet S-10 Blazer

1 Answer

Replace water pump


u need a special wrench to remove the fan from old pump the rest is pretty much like old chevy 350

Mar 20, 2010 | 2002 Chevrolet Blazer

1 Answer

How do i get the fan off of a '99 chevy blazer so i can take the water pump out?


Well lets see.
Top radiator shroud has to come off.
A special tool is required to hold the pulley/waterpump from turning so the large nut on the front can be removed.
some guys leave the serpentine belt on to assist in this part since that large nut can be a real pain.
All in all it seems to take people about 4 hours to do this job of R&R the water pump. Shop might charge two hours labor for it.

Mar 20, 2010 | 1999 Chevrolet Blazer

1 Answer

How to change a water pump?


You will need to remove the upper fan shroud, remove the fan clutch that is threaded onto the water pump it is easiest to get the tool for this or you can use a bar between two of the pulley bolts and use a cresent wrench on the big nut. After you remove the fan clutch there is the small hoses on the top of the water pump and the lower hose on the bottom of pump. Then there are only four bolts holding the pump to the motor. Reinstall in reverse order. Let me know if you need more help.

Jan 06, 2009 | 1999 Chevrolet Blazer

1 Answer

2001chevy blazer


it is not to hard to change the pump but you will need a fan clutch tool. the water pump is on the front of the motor with the fan attached to it.

Dec 02, 2008 | 2001 Chevrolet Blazer

1 Answer

Water pump repair 1997 blazer v6


u may need to take thge fan shroud off, plastic cover.... look at the pulley, should be 4 bolts, take them off with a small wrench, and also u are gonna need to take off the surpentine belt, let me know how it goes

Oct 26, 2008 | 1997 Chevrolet Blazer

Not finding what you are looking for?
2002 Chevrolet TrailBlazer Logo

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...