Question about 2005 Hyundai Elantra

1 Answer

Hi, My elantra has a rattle on front right wheel. it has done 150,000 km It appears to go away if put a light pressure on the brake pedal. Richard

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 583 Answers

Richard , i would think you have a wheel bearing gone or on the way out

Posted on Feb 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front end rattle that goes away when brakes applied


the squeaking sounds like a wheel bearing going bad. And the pulling to one side is cause by unequal braking pressure caused by plugged rubber brake hose, bad calipers or wheel cylinders. Check the bearings by lifting the car with a jack, block the wheels, and use a jack stand for safety. now wiggle the tire around. If it has any play, the bearing is bad. Replace it. I would replace your brakes as well. Good luck

Nov 08, 2013 | Cars & Trucks

1 Answer

Front end noise


front brake pad hardware is worn out , causing pads to move around when jarred , applying brakes tightens pads and noise will go away

Jul 18, 2013 | 2007 Chevrolet Impala LS Sedan New Cars

2 Answers

I have a 1994 buick and i have no brakes i bleed them and still nothing pedal goes all the way to the floor.


YOU NEED A TECH 1 SCANNER TO MOTOR REHOME FUNCTION PISTONS IN THE ABS BRAKE MODULATOR SHOULD BE RETURN TO THE UPPER MOST POSITION.BEFORE YOU CAN BLEED BRAKES.IF YOU DONT HAVE TECH 1 SCANNER SAFELY RAISE SUPPORT FRONT OF VECHICLE USING JACK STANDS. WITH FRONTS WHEELS OFF GROUND EMERGENCY BRAKE APPLIED WITH PUT VECHICLE IN DRIVE LET WHEELS SPIN AT 5 MILES PER HOUR THEN APPLY BRAKE PUT VECHICLE BACK IN PARK.TURN OFF CAR. THEN WAIT FEW MINUTES THEN START ENGINE AGAIN IF THE AMBER ABS LIGHT STILL FLASHES AND DONT TURN OFF HAVE VECHICLE TOWED IN LET DEALERSHIP PRESSURE BLEED AND USE THE TECH 1 SCANNER TO BLEED AND FIX YOU BRAKES FOR YOU.

Sep 27, 2011 | 1995 Buick LeSabre

1 Answer

Put front brakes on hj kingswood bleed brake line .now brake peddle wont work


you need to bleed the brakes,starting from the wheel that's the fartherest away from your master cylinder. if you opened a bleeder valve when you replaced the front brakes,you've let air into the whole brake system.you will need 2 people to bleed the air out of the brakes.1to pump the pedal up for pressure and you to release the pressure of air from the bleeder valves on each wheel.start from the wheel that's the fartherest away from the brake master cylinder. passenger rear wheel.have someone pump the brake pedal up [pump3times]and hold pressure on the brake pedal,you open bleeder valve on the wheel to let the air out,or until the brake pedal goes to the floorboard[never let the person who is pumping the brake pedal to take the pressure off the brake pedal until you've tightened the bleeder valve closed.or else,you're waisting your time. you may have to bleed each wheel twice,or until you see clear brake fluid come out with no bubbles or spurting from each wheel. after you're done with passenger rear wheel,move to driverside rear wheel,then go to passenger front,then drivers front,which is last.when you replaced the brakes,you made a common mistake,you opened the brake lines,which let air into the brake system.it's a very common mistake so don't feel bad.just go back and bleed the brake system.after you do this,you will not make the same mistake again,i guarantee it. thank you for choosing fixya.com and if you need further assistance,please repost your question to fixya.com i'm usually here at least 12 hours a day to assist people for free.that's just me thanks!

Jan 26, 2011 | GMC C3500 Cars & Trucks

1 Answer

2006 dodge ram 2500 4x4 diesel replace brake pads front and back


Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Apr 25, 2009 | 2004 Dodge Ram 2500

1 Answer

No brakes after changing brake caliper & bleeding system


Sounds like you still have air in your brake lines. Make sure all your brake lines are tight. Then bleed again. Bleed the trouble side first, meaning right side, then go to front left, back left then back right, make sure that your brake fluid is also full

Feb 11, 2009 | 2004 Toyota Tacoma

1 Answer

How do you get rotor off 2003 hyundia elantra


hi from uk not sure if same as uk hyundai's but here goes ? if you remove wheel do you see two countersunk posi screws between studs that appear to hold rotor ?? if so then you will have to first remove the brake caliper assy by unbolting from the rear of caliper two 13 mm spanner/socket ? then you remove the two bolts that secure the carrier that the caliper bolts to 17 mm spanner/socket now you can remove the two contersunk screws then you may have to tap the rotor off the hub from rearuse a wire brush to clean up/away all rust/dust from caliper and carrier assys b4 refitting (take precautions from breathing dust) i assume you are fitting new pads ?? reassemble carrier then b4 fitting pads smear a light coating of copper grease on the rear of pad (metal side ) this prevents squealing on brakes then fully reassemble then b4 fitting wheel? bleed the brakee caliper a couple of pumps should expel dirty fluid then fit wheel carry out same proceedure on other brake assy as above fully then b4 you move car pump brake to ensure pedal is firm you will find that bleeding brakes will make pedal firmer as the old fluid becomes compressable due to heat/moisture absorbsion over time and heat from brakes is transferred to fluid via caliper piston understand?? that is why alway policy to bleed/flush brake fluid at least two yr interval this reduces spongy brake pedal hope this is all clear 4 you to follow best wishes for new year and hope you update on how you go on??

Jan 10, 2009 | 2004 Hyundai Elantra

2 Answers

Hyundai 1998 Elantra Growling sound from front


You have a worn right front wheel bearing - all your symptoms are classic signs of wheel bearing failure. You'll likely need a 6-8 ton shop press to replace it. Dropping your car off for the work and picking it up completed can run you $250-300, but many places will charge only $30 or so if you remove the spindle (which houses the bearing) and bring it to them, so they only have to press out the bearing and install the new one.

Sep 17, 2008 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
2005 Hyundai Elantra Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...