Question about 2003 Nissan Murano

1 Answer

My murano was hard in starting after for at least three days. Is this an ignition or fuel problem .

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 204 Answers

Any weird clicking sounds? Could be battery or starter.

Posted on Feb 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 05 nissan murano and when i try to smash it, it starts jerking hard like the engine coming out


Could be a plugged up fuel filter not letting enough fuel to the engine at high RPMs

Jun 22, 2016 | 2005 Nissan Murano

1 Answer

What a fuel filter looks like in a 2004 Nissian Murano


LOOK UNDER AT BACK ON LEFT OR RIGHT SIDE,THREE LINE GOING TO BACK TO TANK.SHOULD SEE LIKE CAN.

May 22, 2016 | 2004 Nissan Murano

2 Answers

How do I fix a trouble code for Nissan Murano P0300?


DTC P0300: Random multiple misfire detected. Probable cause:
1. Vacuum leaks, damaged hoses and/or incorrect routing
2. Fuel contamination
3. Ignition system fault. Check ignition module, coil, spark plugs and wires
4. Fuel system problem

Jan 29, 2015 | 2003 Nissan Murano

1 Answer

2004 Nissan Murano SL periodically wont start.


Sounds like the camshaft sensor is on the way out , the computer needs this info. to set the correct timing. once found the engine starts and is ok till the next start.

May 04, 2017 | Nissan Murano Cars & Trucks

1 Answer

Beeping sound in 2005 nissan murano


Mine did the same thing. I had the battery replaced on the controller.and it still beeped. Then I took my key and put it in the ignition, without turning the key and took it out. Did this like 6 times and the long beep finally stopped.

Apr 07, 2013 | 2005 Nissan Murano

2 Answers

Whenever the murano is idle and the engine is in neutral after a time it shuts off and gives a hard start It alo does this in traffic and especially when it gets hot it just shuts off.


the next time it shuts down check to see if fuel pump is running. if not. check the fuel pump relay, it may be getting hot and shutting down pump. a malfunctioning temperature sensor will often send incorrect information to the vehicle's on-board computer. As a result, when the vehicle reaches a normal operating speed the sensor may relay an incorrect signal to the computer that the engine is overheating resulting in engine shutdown. The vehicle will not be able to start again until the engine has completely cooled and will need to have the sensor replaced in order to prevent the recurrence of the problem. in some cases a bad thermostat will cause this problem also. good-day !

Dec 10, 2011 | 2006 Nissan Murano

1 Answer

Intelkey will not start car ignition will not turn with intelkey or hard key


Sometimes the steering wheel gets torque locked. Try turning the steering wheel one way then another while trying to turn the ignition.

Jan 21, 2011 | 2007 Nissan Murano SE

2 Answers

I have a 93 Chevy G20 VAN G20 with a 4.3L engine that has TBI my van starts and runs for a few days. Then it will not start after sitting for a day or two it starts again and runs fine. What could be the...


There are three relays all grouped together on the firewall on the passengers side. All three are related to your situated. We can eliminate one of them because you stated that the fuel pump is operating fine. Now that leaves the relay for the ECM(engine control module) this tells the injectors, cold start and run, when and how much fuel to supply and also controls ignition timing and spark advance. The third controls the AC compressor. Now I've got to remind you that I started working on fuel injection systems the day they started failing here in the US around 1972.These were such vehicles as Mercedes, Saab and Volvo. I've worked on every configuration, TBI, MPI, diesel etc.etc. I may on occasion cross one fact with another or mispronounce certain aspect of a system however, These three injectors are where you want to concentrate your efforts. With some finnesse you can swap the harnesses from one to another. If your car runs fine and your AC suddenly does not, then you know that that relay is faulty. Do this until you get your answer. Best of luck my friend, Dana

Aug 31, 2009 | 1993 Chevrolet G20

1 Answer

No spark very intermittently


Ignition module. They tend to die an intermittent death.

Aug 08, 2009 | 1996 Ford Crown Victoria

2 Answers

Why car starts but stalls in seconds


Could be the idle air control valve, I have a 1993 Honda Civic Si, they cost about 200 on that to replace.

May 23, 2009 | 2004 Nissan Murano

Not finding what you are looking for?
2003 Nissan Murano Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...